Satellite Electronic 18033 Ceiling Fan Remote Controller User Manual
- June 3, 2024
- Satellite Electronic
Table of Contents
Satellite Electronic 18033 Ceiling Fan Remote Controller
LEARNING PROCESS
The Hand Held Remote Control is equipped with a learning ID function which has
code combinations to prevent potential interference from other remote units.
Step: 1. Install the batteries AAA 1.5V*2 PCS in transmitter. Within 30
seconds of turning the Receiver AC power ON, press the transmitter LEARN
button
Step: 2. Hold LEARN button about 3 seconds, once the receiver has
detected the ID, the light of ceiling fan will be blinking twice and the fan
turn on low speed. This will indicate the receiver has learned the ID that was
previously selected on the transmitter.( The 0/1 switch on the back of the
transmitter is in the “0” state, and it can be directly controlled without
pairing. The 0/1 switch is in the “1” state, need to proceed learning.)
Note:
After the AC power is on, do not press any other buttons on the transmitter before learning ok. Because doing so will cause the procedure to fail. After completing the steps above, you should be able to operate the ceiling fan and light. If the ceiling fan is not responding to the transmitter, please turn the power off to the receiver and repeat step 1 and 2.
Remove the batteries if not used for long periods of time to prevent damage to the hand held remote. The batteries must be removed from the transmitter before it is scrapped and the batteries shall be disposed of safety.
Light function select switch
Slide the D/O switch, located in the battery compartment, to match the bulb type in your fan. “D”(DIMMER) for incandescent bulbs and “O”(ON/OFF) indicates compact fluorescent bulbs (CFL). Use a small screwdriver or ballpoint pen to slide firmly left or right.
FUCNCTIONS OF TRANSMITTER
- Turn on/off ceiling fan
- FAN SPEED(1~9 SPEED)
- Press button to increase speed and LED bar will show at same time. All
- LED is brighten for the highest speed. Press button to decrease speed.
- FAN TIME Setting up that the ceiling fan and light will turn off after 2, 4 or 8 hours automatically.
- For setting natural wind that the fan speeds turn and change at random. It’s three modes for choose. Hold the button about 3 seconds can cancel the natural setting.
- Press and hold this button about 3 seconds for setting forward/reverse airflow of ceiling fan.
To assure continued FCC compliance
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC complianc e:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18033
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF exposure statement
This equipment complies with the FCC and ISED radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>