Satellite Electronic 18018 Ceiling Fan Remote Controller Instruction Manual
- June 5, 2024
- Satellite Electronic
Table of Contents
Electronic 18018 Ceiling Fan Remote Controller
Instruction Manual
IMPORTANT
YOU MUST SET THE CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHT KIT (IF
ANY) TO ON POSITION BEFORE OPERATING THE REMOTE CONTROL.
IMPORTANT POINTS TO REMEMBER
- Read and save these instructions.
- Please note that all fixed wiring appliances should be installed by a qualified electrician.
- The supply to the remote control receiver should be connected through a mains switch, i.e. existing wall switch.
- Disconnect from the power supply at wall switch before working on the remote control receiver or ceiling fan.
- Install the receiver into the ceiling fan canopy of the fan to ensure proper protection.
- This unit is to be used for the control of the ceiling fan and in an AC120V 60Hz power supply only. Load: fan motor 1.0A Max and 190 W Tungsten load and Electronic Ballast Load (or LED for Light).
- Do not install in damp locations or immerse into water. (For indoor use only.)
- Do not pull on or cut leads shorter.
- Do not drop or bump the unit.
- PLEASE NOTE: The battery will weaken with age and should be replaced before leaking takes place as this will damage the transmitter. Dispose of used battery properly, and keep the battery out of reach of children.
- CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with any variable (rheostat) wall control.
INSTALLATION INSTRUCTIONS
CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
- The ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the “Pull Switch” after installation.
- Once the connection has been made, the receiver inserts into the drop rod hanging bracket. The canopy comes up to cover the receiver and bracket.
LEARNING PROCESS
After installing the unit and power on, open the battery cover (with
batteries, DC12V/1pcs, installed), and press the remote’s key to control the
ceiling fan for the learning process. Please note that press any button within
1 minute after power on. If just replace batteries, no need to re-learn.
Please note that the transmitter can learn in multiple receivers, when doing
the learning process please make sure not to learn in another receiver.
FUNCTIONS OF TRANSMITTER
| : Turn on the fan at high speed
---|---
| : Turn on the fan at medium speed
| : Turn on the fan at low speed
| : Turn off the ceiling fan.
| Press and turn the light on or off.
DIMMER-Press and hold to dim or brighten light to the desired level and
release.
(Tungsten or dimmer-able LED.)
To assure continued FCC compliance:
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18018
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>