BRANDSON 304257 Digital Irrigation Computer User Manual

User Manual

Mod.-Nr.: 304257/20191212NB128

The latest information, drivers, user manuals, and data sheets can be found at www.ganzeinfach.de in our download area.

Thank you for choosing a Brandson product. Please read the following user manual carefully so as to get the most from the product you have purchased. Before using the product, first check that the delivered item is complete, accurate, and undamaged.

Scope of delivery

• Watering control system
• 1/2″ plug for hose connector
• 1/2″ connection adapter
• User manual

Technical data

• Water discharge 3/4″ (outlet / without adapter)
Dimensions (H x W x D)| 150mm x 120mm x 90mm
Features| • Manual operation
• Adjustable watering program

Product details

Replacing/inserting batteries

The display shows when the batteries are empty. The battery indicator flashes on the display.
Open the battery compartment lid at the back of the removable panel. Remove the cap and insert two AA 1.5V batteries. Particularly make sure the polarity of the contacts is correct. Then close the battery compartment cover. Replace the control panel with the watering system computer.

Caution! Use only new batteries. Do NOT use rechargeable batteries.

Initial use

Time and day

1. Press the menu (Menu) button to adjust the time. The TIME starts flashing in the display. Press the OK button to access the setting.

2. The hour display then starts flashing. Use the dial to adjust the hours. Turn it left to reduce the value or turn it right to increase the value. Once you reach the desired hour,
   confirm by pressing the OK button.

3. Then the minute display starts flashing. Using the dial, adjust the minutes desired and confirm by pressing the OK button.

4. Next, the current day is highlighted. Select the current day using the dial and confirm it using the OK button.

Note: The menu items of the hour, minute, and day can also be navigated using the “Increase value” and “Decrease Value” buttons.

Connecting

1. Connect the water tap connection of the watering system computer directly to the desired water tap.
2. Connect the hose of the desired watering system to the water outlet (hose connection) using a suitable connector.
3. The device is now ready for use.

Initial use

Defining the start time
Adjust the start time for watering after connecting the watering system computer to the tap and the hose of the watering system.

1. Press the Menu button twice. START flashes on the display. Open the settings by pressing the OK button.
2. Use the dial to set the value for the start time. First set the hours. Confirm using the OK button. Then set the minutes. Turn it left to reduce the value or turn it right to increase the value. Confirm using the OK button.

Defining the watering duration
After setting the start time, the hour display of watering duration (Run-Time) starts flashing.

1. Adjust the watering duration using the dial. Turn it left to reduce the value or turn it right to increase the value. First, select the hours. Confirm using the OK button.
2. Then adjust the minutes of run time. Confirm using the OK button.
   Note: The run time can be set to a maximum of 240 minutes (4 hours).

Defining the watering cycle
After adjusting the start time and watering duration, you can define the watering cycle.
The following watering cycles are available:

• every 6 hours,
• every 12 hours
• on any selected days of the week.

The display shows a water drop symbol on the right side ( ) after the watering time (Run-Time) is set.
You can adjust the watering cycle using the two “Increase value” and “Decrease value” arrow keys. The current setting is shown in the display using the water drop symbol.
You can also select multiple days by selecting the day using the “Increase value” and “Decrease value” arrow keys and confirming by pressing the OK button. The water drop symbol ( ) is shown for the selected days.

Enabling the program
The display shows “PROG” once the watering cycle is configured. You have the option of enabling the program (On) or disabling it (Off).
Use the dial to choose between the two options and confirm by pressing the OK button.

• When enabled, the display shows the water drop symbol ( ) of the previously configured cycle. The symbol disappears once the program is disabled.

Rain Delay function
This feature is not supported by this device. If you accidentally set a Rain Delay (which is shown at the bottom of the screen), press the “Increase value” and “Decrease value” arrow keys simultaneously to disable the Rain Delay function.

Manual operation

You can override the automatic watering cycle with the manual operation.

1.  Press the manual button (Man.) to access manual operation.
2. Adjust the watering duration (Run-Time) using the dial. The run time can be configured to a maximum of 240 minutes.
3. Then press the OK button to confirm.
4. To turn off the manual operation and switch to automatic mode, press the manual (Man.) button.

Additional safety instructions

• The timer is water-resistant, NOT waterproof. The timer has to be installed above ground and vertically to the tap. Do not immerse the device in the water!
• DO NOT pull the hose when it is connected to the watering control system to avoid damage to the timer.
• This timer is intended for outdoor use, to control watering systems.
• The device should not be used for industrial purposes
• The water pressure is between 0.2 bar and 8 bar (0 psi to 116 psi). Use only with clean water and freshwater, the water temperature has to be above 1°C and below 60°C.
• Protect the timer during the winter season or from frost. Disassemble the device from the tap and drain all the water from it. Remove the batteries and keep the device and the batteries safely at home.
• Always keep the cover closed to prevent water from entering.
• Do not use the device if it has fallen down or has been subject to impact.
• Ensure that you clean the filter regularly if it is dirty.

Cleaning

Clean the filter in the water tap connection regularly to prevent your watering system computer from clogging.

Safety instructions and disclaimer

Never try to open the device to repair or make modifications. Avoid contact with the mains voltage. Do not short-circuit the product. The device is not approved for outdoor use. Therefore please use it only in dry surroundings. Protect it from high humidity, water, and snow. Keep the device away from high temperatures. Do not expose the device to sudden changes in temperature or strong vibrations, as this could damage the electronic components. Check the device for any damage before using it.
The device should not be used if it was subject to impact or has been damaged in some other manner. Please comply with the local regulations and restrictions. Do not use the device for purposes other than those described in the user manual. This product is not a toy. Keep it out of the reach of children or mentally disabled persons. Any repair or modification to the device, which is not carried out by the original supplier, will void any warranty and guarantee claims. The product should be used only by persons who have read and understood this user manual. The specifications of the device may be changed without any special prior notice.

Disposal instructions

In line with the European WEEE directive, electrical and electronic devices should not be disposed of along with domestic waste. Their components have to be separately sent for recycling or disposal, because improper disposal of toxic and dangerous components may permanently damage the environment. According to the electrical and electronic equipment act (ElektroG), you are obliged (as a consumer) to return (free of charge) all electrical and electronic devices to the manufacturer, the point of sale, or public collection points at the end of their service life. The relevant local laws regulate the details in this regard. The symbol displayed on the product, in the user manual, or/and on the packaging refers to these regulations. With this manner of sorting, recycling, and disposal of used devices, you make an important contribution towards protecting our environment.

Instructions for battery disposal

In conjunction with the sale of batteries along with the supply of devices that include batteries, the supplier is obliged to point out the following to the customer: The customer is legally obliged to return used batteries. He can return used batteries which the supplier offers or has offered as new batteries in his assortment free of charge to the supplier’s dispatch warehouse (shipping address). The symbols shown on the batteries indicate the following: Pb = battery contains more than 0.004 percent lead by weight, Cd = battery contains more than 0.002 percent cadmium by weight, Hg = battery contains more than 0.0005 percent mercury by weight.

The symbol of the crossed-out dustbin means that the battery may not be disposed of in the household waste.

WEEE directive: 2012/19/EU
WEEE Register no.: DE 67896761

The company WD Plus GmbH hereby certifies that the device 304257/20191212NB128 complies with the fundamental requirements and all other relevant stipulations. A  complete conformity statement can be obtained from WD Plus GmbH, Wohlenbergstraße 16, 30179 Hanover

WD Plus GmbH
Wohlenbergstraße 16 · 30179 Hannover
Germany

Documents / Resources

| BRANDSON 304257 Digital Irrigation Computer [pdf] User Manual
304257, Digital Irrigation Computer
---|---

References

• WD Plus - WD Plus
• WD Plus - WD Plus

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>