APEX CUSTOMS Sensei Plus 5-6 Inch DA RO Polisher Premium Pack Instruction Manual
- October 31, 2023
- APEX CUSTOMS
Table of Contents
APEX CUSTOMS Sensei Plus 5-6 Inch DA RO Polisher Premium Pack
Product Information
- Brand: Apex Customs
- Product Name: The Sensei 15mm / 21mm Dual Action Random Orbital Polisher
- Pad Size Compatibility: 125mm / 5 or 150mm / 6
- Max Power: 1000 Watts
- Variable Speeds: 2000 – 5000 OPM
- Max Noise Levels: 65dB @1m
- Orbit Size: 15mm or 21mm
- Weight: 2.6kg
- Voltage: 220 – 240V AC
Product Usage Instructions
- NEVER start the machine before the backing pad is installed.
- Make sure the fastener on the backing pad fits the spindle on the machine well and use the Hex wrench to install the backing pad tightly. If the backing pad becomes difficult to remove, use a longer Hex key as leverage.
- Align the backing pad with the foam pad’s center. Otherwise, vibration may be excessive.
- Generally, lower speeds are recommended for tight work areas while higher speeds are ideal for larger surface areas.
- To prevent burning through paint, use very light pressure and keep the polisher moving constantly.
- Use the polisher at low speeds while polishing rough surfaces.
- For tricky or tight areas, use coast-down to polish. To do so, turn the machine on for a few seconds to enable it to oscillate, then turn it off and use the residual oscillations to polish.
- The shaft lock button is for removing or installing the counter weight set. NEVER press it while the machine is running.
Troubleshooting
- If large sparks are visible from the side vents of the machine, the carbon brushes may need to be replaced. Kindly contact the Apex Customs customer support team for further information on how to replace these.
- If the machines become noticeably noisier over time, stop using immediately and inspect if the bearings or counter weight are damaged / misaligned.
Key Features
- Non-slip rubberized grip
- Optional U-shaped ambidextrous handle mount
- Constant speed controller with 6 speed settings
- 4-meter cord
- 5/6 backing plate
- Switch self-locking button
- Progressive switch for a soft start
- Precision engineered counterweight for optimal balance
Best practice
- NEVER start the machine before the backing pad is installed.
- Make sure the fastener on the backing pad fits the spindle on the machine well and use the Hex wrench to install the backing pad tightly. If the backing pad becomes difficult to remove, use a longer Hex key as leverage.
- Align the backing pad with the foam pad’s center. Otherwise, vibration may be excessive.
- Generally, lower speeds are recommended for tight work areas while higher speeds are ideal for larger surface areas.
- To prevent burning through paint, use very light pressure and keep the polisher moving constantly.
- Use the polisher at low speeds while polishing rough surfaces.
- For tricky or tight areas, use “coast-down” to polish. To do so, turn the machine on for a few seconds to enable it to oscillate, then turn it off and use the residual oscillations to polish.
- The shaft lock button is for removing or installing the counter weight set. NEVER press it while the machine is running.
Troubleshooting
- If the polisher does not start, check the following:
- Is the power source active?
- Is the power cable on the the machine damaged?
- Are any screws on the switch loose?
- Is the switch or the speed controller damaged?
- Is the armature or stator damaged?
- If large sparks are visible from the side vents of the machine, the carbon brushes may need to be replaced. Kindly contact the Apex Customs customer support team for further information on how to replace these.
- If the machines become noticeably noisier over time, stop using immediately and inspect if the bearings or counter weight are damaged / misaligned.
Key features
Stay safe
To reduce risks associated with the use of the polisher, please carefully read
the following instructions.
Work area
- Do not operate the polisher while near or exposed to flammable liquids or gases.
- Keep a safe distance from bystanders while operating the polisher.
Electrical safety
- There should be no modification of the polisher in any way.
- Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators.
- Do not expose the polisher to water or leave it in an area where it may become wet.
- Do not use the polisher in any wet weather conditions.
- Keep the cord away from any heat, oil, sharp edges or moving parts
Personal safety
- Do not use the polisher while you are tired or under the influence of drugs, alcohol or medication.
- Use personal protective equipment such as safety glasses and gloves.
- Ensure the switch is in the off position before connecting to a power source.
- Remove any adjusting key or wrench before turning the polisher on.
Polisher use and care
- Do not use the polisher if any of the parts are broken, misaligned or showing signs of excessive wear.
- Disconnect the plug from the power source before making any adjustments, change in accessories or when storing the polisher.
- Keep the polisher clean and well maintained to prolong its intended life cycle. If damaged, have the polisher repaired by an authorised repairer or contact the Apex Customs customer support team for further information.
Service
- Please note that the standard 12 month warranty from date of purchase will be void if your polisher has been tampered with or serviced by a non qualified Apex Customs repairer. Only use original parts supplied by Apex Customs.
specifications
The Sensei Plus specifications
-
Pad size compatibility
125mm / 5” or 150mm / 6” -
Max power
1000 Watts -
Variable speeds
2000 – 5000 OPM -
Max noise levels
65dB @1m -
Orbit size
15mm or 21mm -
Weight
2.6kg -
Voltage
220 – 240V AC
Warranty
Register your Apex Customs polisher online, and we will keep track of the paperwork for you. Visit apexcustoms.online/warranty. or scan the QR code. 15mm / 21mm Dual Action Random Orbital Polisher apexcustoms.com.au. Bringing back that showroom shine
References
Read User Manual Online (PDF format)
Loading......