BRANDSON 301770 Calendar Desk Lamp User Manual

BRANDSON 301770 Calendar Desk Lamp

Thank you for choosing a Brandson product. Please read the following user manual carefully to have an enjoyable experience with your purchased product. Before using the delivered product, check that it is complete, faultless and undamaged.

Scope of delivery

• LED lamp
• DC coaxial power connector (3.5mm)
•  User manual

Technical data

•  Temperature and calendar function

•  Alarm function

•  Touch-controlled and dimmable

Product details

Initial use

When the device is put into operation for the first time, check the intactness of the product or components and their function again. Take the device out of the package and remove all the packaging material. Place the lamp on a flat and even surface, so that it does not fall over. Remove the battery safeguard on the rear of the lamp by turning the battery compartment anticlockwise and removing the plastic washer between the battery and the contact. Then close the battery compartment properly again.
Then insert the supplied DC coaxial power connector into a properly installed power socket and connect it to the lamp in order to start using it.
You can switch the lamp on or off by touching “ON / OFF”.
Touch the “Mode” button to select one of the three light modes (natural, white and yellow light). To adjust the brightness of the lamp, touch the “increase” or “decrease” button (with the lamp switched on) until you get the desired brightness.

Display functions

First, set the current time and the current date. To do this, press the “SET” button on the back of the lamp. The time starts flashing. Set the desired time using the “UP” and “DOWN” buttons. Confirm your entry using the “SET”   utton. The setting sequence is as follows: Hour -> Minutes -> Year -> Month -> Day. Press the “UP” button to change between the 12-hour and 24-hour display. Press the “DOWN” button to change between °C and °F.  Press and  old the “ON/OFF” button for 3 seconds in order switch on or off the display light.

Alarm function:
Press the “MODE” button to display the currently set alarm. Press the “SET” button once the display shows the alarm time. Now you can enter the desired alarm time. Confirm the settings by pressing the “SET” button.

The setting sequence here is as follows: Hours - > Minutes -> Snooze time -> Alarm.
Press any button on the rear of the device to stop the alarm and to turn off the alarm completely.
Press the “MODE” button to turn on the alarm, so that you are in alarm mode. You can turn the alarm on or off using the “UP” and “DOWN” buttons. The alarm is turned on when the symbol ” ” appears in the display.

The setting sequence of the alarm is as follows: Alarm On - > Alarm and Snooze function On -> **Alarm Off.
** The alarm rings for one minute. If you do not press any button during this time and the alarm is thus turned off, the previously set snooze mode is enabled. The alarm goes off once again after the set snooze time, till a button is pressed on the rear of the device and the alarm is completely turned off.

Safety instructions and liability disclaimer

Never try to open the device to carry out repairs or conversions. Avoid contact with mains voltages. Do not short-circuit the product. The device is not certified for use in the open air; only use it in dry conditions. Protect it from high humidity, water and snow. Keep it away from high temperatures. Do not subject the de-vice to sudden changes in temperature or heavy vibration as this might damage electronic components. Examine the device for damage before using it. The unit should not be used if it has received an impact or has been damaged in any other way. Please observe national regulations and restrictions. Do not use the device for purposes other than those described in the instructions. This product is not a toy. Keep it out of the reach of children or mentally impaired persons. Any repair or alteration to the device not carried out by the original supplier will invalidate the warranty or guarantee. The product may only be used by persons who have read and understood these instructions. The device specifications may change without any separate prior notice to this effect.

Disposal instructions

Electrical and electronic devices may only be disposed of in accordance with the European WEEE Directive and not with household rubbish. Components must be disposed of or recycled separately as dangerous, toxic elements can inflict sustained damage on the environment if they are disposed of incorrectly. As a consumer, you are bound by the Electrical and Electronic Devices Act (ElektroG) to return electrical and electronic goods free of charge at the end of their useful life to the manufacturer, the place of purchase or to specially set up, public collection points. The details in each case are governed by national law. The symbol on the product, the operating instructions, and/or the packaging refers to these regulations. By separating materials in this way, recycling and disposing of old devices, you are making an important contribution towards protecting our environment.

Instructions on the disposal of batteries

With regard to the sale of batteries or the supply of devices containing batteries, the supplier is obliged to draw the customer’s attention to the following:
As the end-user, the customer has a statutory obligation to return used batteries. He can return old batteries stocked or previously stocked by the supplier in the form of new batteries to the supplier’s despatch warehouse (despatch address) free of charge. The symbols shown on the batteries have the following meanings: Pb = battery contains more than 0.004 percent by mass of lead, Cd = battery contains more than 0.002 percent by mass of cadmium, Hg = battery contains more than 0.0005 percent by mass of quicksilver.

The symbol of the rubbish bin with a cross-through it indicates that the battery may not be put in household waste.

References

• WD Plus - WD Plus
• WD Plus - WD Plus

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>