Sylvox OT65A1KAGC Outdoor TV User Manual

Outdoor TV
User Manual

Designed in California, Assembled in China

Note: The product and illustrations in this user’s manual is only for explanation purposes and may vary depending on model

This manual covers models
OT43A1 KAGB
OT43A1 KAGC
OT43A1 KAGE
OT55A1 KAGB
OT55A1 KAGC
OT55A1 KAGE
OT65A1 KAGB
OT65A1 KAGC
OT65A1 KAGE

General Information

To avoid damaging the television set please observe the following safety instructions during setup and use.

Cleaning the television set| Before cleaning, disconnect the television set. Use only a soft damp cloth or a special cleaning product for flat screens.
---|---
LED Display Heat/damp/humidity| Too much pressure on the screen can damage the television set.
The television set should not be exposed to high temperatures (radiators, open fire).
The television set should not be used in areas with high humidity.
Condensation| If moving from a cool area to one with a higher temperature, the television set should be left for at least an hour before plugging it in. A rapid change of temperature can lead to the formation of condensation in the television set itself. This can lead to damage if the television set is in use.
Air Circulation| To prevent overheating of the television set the ventilation slots at the rear should always be clear.
Small Objects| It is important to ensure that no small objects or liquids enter the television set. They can cause damage or even fire.
Liquids/Candles| Do not place anything holding a liquid or any candles on the television set.
Crushing| Take care to avoid crushing fingers or other objects when turning the television set in any direction.
Electric Supply Moving the Television Set| Use the television set only with the voltage indicated in the specifications.
Ensure that there is easy access to the plug and that the television set can always be disconnected from the electricity supply.
Do not disconnect the television set by pulling the power cable. Always take hold of the plug. The power cable must not be kinked or placed over sharp edges.
When moving the television set, hold only the casing.

In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains. The main plug is used to disconnect the TV set from the mains and therefore it must remain readily operable. If the TV set is not disconnected electrically from the mains, the device will still draw power for all situations even if the TV is in standby mode or switched off.

IMPORTANT – Please read these instructions fully before installing or operating
WARNING: Never let people (including children) with reduced physical, sensory or mental capabilities or lack of experience and/or knowledge use electrical devices unsupervised.

• The TV set is intended for Outdoor and similar general use but may also be used in public places.
• For ventilation purposes, leave at least 5cm of free space around the TV.
• The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.
• The power cord plug should be easily accessible. Do not place the TV, furniture, etc. on
• the power cord. A damaged power cord/plug can cause fire or give you an electric shock. Handle the power cord by the plug, do not unplug the TV by pulling the power cord. Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock. Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced, this should only be done by qualified personnel.
• Do not expose the TV to dripping or splashing of liquids and do not place objects filled with liquids, such as vases, cups, etc. on or over the TV (e.g., on shelves above the unit). • Do not do not place open flames such as lit candles on the top of or near the TV.
• Do not place any heat sources such as electric heaters, radiators, etc. near the TV set.
• Do not place the TV on the floor and inclined surfaces.
• To avoid the danger of suffocation, keep plastic bags out of the reach of babies, children, and domestic animals.
• Do not dispose of the batteries in fire or with hazardous or flammable materials.
• Warning: Batteries must not be exposed to excessive heat such as sunshine, fire, or the like
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

WARNING Never place a television set in unstable or inclined locations. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such, Educating children about the dangers of climbing on furniture to reach the television set or its controls.
WALL MOUNTING WARNINGS
Read the instructions before mounting your TV on the wall. The wall mount kit is optional. Do not install the TV on a ceiling or on an inclined wall. Use the specified wall mounting screws and other accessories. Tighten the wall mounting screws firmly to prevent the TV from fall. Do not over-tighten the screws.
WARNING
This is not a recessed installable TV, Do not insert TV into the wall.

Accessories

Please make sure the following items are included with your TV. If any items are missing, please contact us.

TV Specification

Note: Design and specification modification may be made at any time without prior notice, all data and dimensions are approximations.

Installation

Waning – Please read before installation (Mounting Brackets are not supplied with TV)
Please thoroughly read the instructions before attempting installation The only suitable for the 43–65″Outdoor TVs. We advise that 2 people install the screen due to the heavy load of the screens. Please be sure the mounting surface is strong enough to hold the weight of the screen.
Step—Mounting Bracket to Wall Fix the horizontal bracket into the wall with screws.

Step2—Mounting bracket to TV Fix the vertical bracket on the back of TV with screws.
Step 3—Mounting TV to Bracket Attach TV with brackets on the wall.

Overview

Auto-brightness control sensor (1500cdfm’ Series only) Automatically adjusts the screen brightness according to the ambient light.

1. REMOTE CONTROL SENSOR
2. POWER INDICATOR
3. Green: In power-on mode.
4. Red: In standby mode.

Remote-Control unit

Loading batteries:

1. Remove the lid of the battery compartment.
2. Insert 2 size AAA batteries with polarities as indicated inside the compartment.
3. Replace the lid.

Note

1. A loading of batteries should be last one year under normal use.
2. If you don’t intend to use the remote control for a long period of time, remove batteries to avoid damage due to leakage.
3. Do not mix old and new batteries or different types.
4. Do not throw batteries into fire or water.
5. The batteries (battery pack or batteries installed) should not be exposed to excessive heat such as sunshine, fire or the like.

Remote-Control unit

1. POWER: Turn the TV on and off.
2. INPUT: This button is used to switch among different sources, Select a source and press ENTER button to confirm.
3. Digital Buttons(0-9, •): Directly select channels with digital buttons.
4. CHRTN: Switch to the previous program.
5. YouTube: If the network connects, press this key to view YouTube directly.
6. LIST: Press it to show channel list and favorite list on the screen.
7. HOME: Press it to go to the App home page.
8. NETFLIX: If the network connects, press this key to view NETFLIX directly.
9. Q.MENU: Press this key to go to the quick menu.
10. MENU: Display the main menu or exit the current menu.
11. ENTER: Validation key.
12. Arrow buttons Use to select on-screen menu items and change menu values.
13. BACK: Return.
14. EXIT: Exit the menu.
15. COLOR BUTTONS: It’s used as it’s shown in the EPG or Program Edit menu.
16. VOL+/-: Press these buttons to adjust the volume.
17. MUTE: Press this button to cut off the sound of the TV set temporarily, press again to resume.
18. ZOOM: Press this button to select the aspect ratio of the screen.
19. CH •l• : Press these buttons to change the channel upward or downward.
20. DIGITAL MEDIA PLAYER CONTROL BUTTON: Include play/pause, stop, previous, next, backward, forward is used in USB mode. No record function. Please refer to relevant instructions in the section of multimedia player.
21. INFO: Display the program information.
22. MTS/AUDIO: In USB mode, press this button to switch the audio track when the movie is playing. In TV mode, press this button to switch MTS or Audio Language.
23. PICTURE: Press this button to select among Sports, Normal, Mild, User.
24. SOUND: Press this button to select among Standard, Sports, Movie, Music, User.
25. CC: Display the CC function menu in TV/AV mode.

Main Menu User Guide

Input Setup
Press the INPUT key on the remote control to enter the “INPUT SOURCE menu. Use ► the key to select an input source and press ENTER key to confirm.
Channels Selection
There are four ways to select a channel:

1. Use number keys, and “ENTER” keys on the remote control to select a channel directly. To select channel 90, press 0C) -•(;) . When you use the number buttons, you can directly select channels that were either erased or not memorized.
2. Use CH /► key on the remote control or on your TV to select a channel. When you press the CH /► key, the TV changes channels in sequence. You will see all the channels that the TV has memorized. You will not see channels that were either erased or not memorized.
3. Press the CH RTN key to return to the previous channel, press it again to return to the current channel. To quickly switch between two channels that are far apart, tune to one channel, then use the number keys to select the second channel. Then use the CH RTN button to quickly alternate between them. CH RTN is not activated if no channel has been changed after the TV turning on.
4.  Select channels from “Channels List” or “Favorite List”. Press the “ENTER” key to choose from the “Channel List” menu.

Volume Adjustment and Mute Setup
Volume adjustment Press VOL+ I – key on the remote control or the TV to display the “Volume” menu, adjust the volume of TV between 0 to 100 by using VOL+ / -key:
To increase the volume, press VOL + key: ( To decrease the volume, press VOL – key;
Mute Press “MUTE° and the sound cuts off. The MUTE icon will appear in the lower-right corner of the screen. To resume sound, press the “MUTE° button again, or simply press the VOL+ key.
4 Current Channel Information
Press the “INFO” key on the remote control to view current channel information, the indications of channel information are listed in the following table.
Press the “EXIT” key on the remote control to exit this OSD.
Picture

1. Press the MENU key to display the main menu on the screen.
2. Press the /► key to select the “Picture” option.
3. Press /► the key to enter the “Picture’ submenu.

Sharpness
Adjusts the outline of objects to either sharpen them or make them dull.
Tint
Adjusts the Tint of the picture.
Backlight
Automatic brightness adjustment does not support manual brightness adjustment.
Color Temperature
You can change the color of the entire screen according to your preference.

1. Press the /►key to select the “Color Temperature’ option.
2. Press the /► key to select one color temp.

Aspect Ratio

1. Press the /►key to select the ‘Aspect Ratio” option.
2. Press the /► key to change the size of the picture on the screen.
   Noise Reduction Press the p/q key to select the Noise Reduction mode. You can select the right model to match the pictures.

Open HDR

1.  Press /► key to select the “Open HDR’ option.
2. Press /► key to select “On” or ‘Or

Sound

1. Press the MENU key to display the main menu on the screen.
2. Press /► key to select the “Sound” option.
3. Press ► the key to enter the “Sound” submenu.

Sound Mode
You can select the type of special sound effect to be used when watching a given broadcast. Your TV has five sound settings (“Standard”, “Music”, “Movie”, “Sport”, “User”) that are preset at the factory.

1. Press the p/q key to select the “Sound Mode” option.
2. Press the Vu key to select one sound mode.

Standard: Selects the normal sound mode.
Music: Provides clear and live sound for music.
Movie: Provides live and full sound for movies.
Sports: Emphasizes bass over other sounds.
User: Selects your custom sound settings.
Equalizer Set sound equalizer mode.
Balance If the volumes of the left speaker and the right speaker are not the same, you can adjust the ‘Balance” to suit your personal preference.

1. Press /►key to select the “Balance” option.
2. Press /► key to decrease or increase the value of the item.

Auto Volume Limit
Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the volume every time the channel is changed. “AVL” automatically adjusts the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

1. Press the /► key to select the “AVL” option.
2. Press /►key to select “On” or “Off.

Surround sound
This is used to turn on surround sound to gain better sound effects.

1. Press the /► key to select the “Surround sound” option.
2. Press the /► key to select “Surround” or “Off”.

Dolby Audio Process
This is used to set DAP.

1. Press /► key to select the “Dolby Audio Process” option.
2. Press /► key to select “On” or “Off.

Sound
Digital Output Type
This is used to set digital audio output.

1. Press /►key to select the ‘Digital Output Type” option.
2. Press /► key to select a digital output type in DTV or HDM I mode.

Audio Delay
This used to set audio type

1. Press /► key to select “Audio Delay”, then press Enter or u button to enter the sub-menu.
2. Press /► key to decrease or increase the value of the item.

Setting

1. Press the MENU key to display the main menu on the screen.
2. Press the /► key to select the “Setting” option.
3. Press ► the key to enter the “Setting” submenu.

Language

1. Press /► key to select “OSD Language” setting
2. Press ENTER or ► key to select a proper language for OSD.

OSD Time Set the preferred amount of time for the OSD to be displayed on the screen.
Close Caption

1. Press /► key to select the “Closed Caption” option
2. Press /► to select Closed Caption mode.

Link Setup

1. Press /► key to select the “Link Setup” option.
2. Press ► the key to enter the “Link Setup’ submenu.

Link-CEC
Turn on or turn off the Link-CEC function.
HDMI ARC
Turn on or turn off the HDMI ARC function.
Auto Power
Turn on or turn off the Auto Power function.
Auto Standby
Turn on or turn off the Auto Standby function.
Time

1. Press the MENU key to display the main menu on the screen.
2. Press /► key to select the “Time” option.
3. Press ► the key to enter the ‘Time” submenu.

Auto Sync
You can modify the time of your TV set in Manual mode. In Auto Mode, the “clock” is decided by the DTV signal. few minutes and don’t turn off the power, it will turn off automatically when updating finish.
Clock– :–
When Auto Sync is on, the clock is got from DTV streams: Set the clock when Auto Sync is off.
Off Time
In the “Off Time” item, press ► the button or ENTER button to enter the submenu, set the day & time to turn off the TV set.
On-Time
In the “On Time” item, press ► the button or ENTER button to enter the submenu, set the time to turn on the TV set when the TV set is in standby mode. You can also choose which day to control your TV set in a week.
Sleep Timer

1. Press /►key to select the “Sleep Timer” option.
2. Press /► key repeatedly until the desired time appears (Off, 10mins, 20mins, 30mins, 60mins, 90mins, 120mins, 180mins, 240mins).

Notes: The sleep timer you have set will be canceled when the TV turns off or if a power failure occurs.
Notes: When the time is less than 60 seconds, reminder information will be displayed on the screen. Press any key button to cancel the timer function.
Auto Sleep
Press /►key to select whether to open the No signal Power off features. If this function is opened, the TV will power off when there is no signal.
Time Zone
You can choose to modify your time zone in the TV set.

1. Press /► key to select the “Time Zone” option.
2. Press /► key to select a time zone.

Reset

1. Press the “ /►” key to select the “Reset” option.
2. Press the /►ENTER” key to confirm.
3. Press “Yes” to confirm again, the TV will turn off auto mastic and change all settings to factory settings.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>