SYWaterproof TV LVOX WT24A0KAGA 24-inch User Manual

SYWaterproof TV LVOX WT24A0KAGA 24-inch

General Information

To avoid damaging the television set please observe the following safety instructions during setup and use.

Cleaning the television set

| Before cleaning, disconnect the television set. Use only a soft damp cloth or a special cleaning product for flat screens.
---|---
LED Display Heat/damp/humidity| Too much pressure on the screen can damage the television set.
The television set should not be exposed to high temperatures (radiators, open fire).
The television set should not be used in areas with high humidity.
Condensation| If moving from a cool area to one with a higher temperature, the television set should be left for at least an hour before plugging it in. A rapid change of temperature can lead to the formation of
condensation in the television set itself. This can lead to damage if the television set is in use.
Air Circulation| To prevent overheating of the television set the ventilation slots at the rear should always be clear.
Small Objects| It is important to ensure that no small objects or liquids enter the television set. They can cause damage or even fire.
Liquids/Candles| Do not place anything holding a liquid or any candles on the television set.
Crushing| Take care to avoid crushing fingers or other objects when turning the television set in any direction.
Electric Supply| Use the television set only with the voltage indicated in the specifications.
Ensure that there is easy access to the plug and that the television set can always be disconnected from the electricity supply.
Do not disconnect the television set by pulling the power cable. Always take hold of the plug. The power cable must not be kinked or placed over sharp edges.
Moving the Television Set Repairs/Accessories| When moving the television set, hold only the casing.
Repairs and servicing must be undertaken only by authorized and trained personnel.
| In accordance with the Batteries Regulation, batteries are to be disposed of only in containers provided for this purpose.

In extreme weather (storms, lightning) and long inactivity periods (going on holiday) disconnect the TV set from the mains. The main plug is used to disconnect the TV set from the mains and therefore it must remain readily operable. If the TV set is not disconnected electrically from the mains, the device will still draw power for all situations even if the  TV is in standby mode or switched off.

IMPORTANT Please read these instructions fully before installing or operating WARNING: Never let people (including children) with reduced physical, sensory or mental capabilities or lack of experience and/ or knowledge use electrical devices unsupervised.

• The TV set is intended for Waterproof and similar general use but may also be used in public places.

• For ventilation purposes, leave at least 5cm of free space around the TV.

• The ventilation should not be impeded by covering or blocking the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.

• The power cord plug should be easily accessible. Do not place the TV, furniture, etc. on

• the power cord. A damaged power cord/plug can cause fire or give you an electric shock.
  Handle the power cord by the plug, do not unplug the TV by pulling the power cord. Never touch the power cord/plug with wet hands as this could cause a short circuit or electric shock. Never make a knot in the power cord or tie it with other cords. When damaged it must be replaced, this should only be done by qualified personnel.

• Do not expose the TV to dripping or splashing of liquids and do not place objects filled with liquids, such as vases, cups, etc. on or over the TV (e.g., on shelves above the unit).

• Do not place open flames such as lit candles on the top of or near the TV.

• Do not place any heat sources such as electric heaters, radiators, etc. near the TV set.

• Do not place the TV on the floor and inclined surfaces.

• To avoid the danger of suffocation, keep plastic bags out of the reach of the babies, children and domestic animals.

• Do not dispose of the batteries in fire or with hazardous or flammable materials.

• Warning: Batteries must not be exposed to excessive heat such as sunshine, fire or the like.

• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

WARNING
Never place a television set in unstable or inclined locations. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such, Educating children about the dangers of climbing on furniture to reach the television set or its controls.

WALL MOUNTING WARNINGS
Read the instructions before mounting your TV on the wall. Do not install the TV on a ceiling or on an inclined wall.
Use the specified wall mounting screws and other accessories.
Tighten the wall mounting screws firmly to prevent the TV from falling. Do not over-tighten the screws.

Accessories

Please make sure the following items are included with your TV. If any items are missing, please contact us.

TV Specifications

Note:
Design specification and modification may be made at any time without prior notice, all data and dimensions are approximations.

Installation

Note:
Ensure that you get the correct viewing position when installing your mounting plate. Once you have got the correct position check that there are no hazards around the area of installation, for example, cables or pipes.

Step 1
Please use our Mounting plate TV sizes below to cut out a recess in the wall to fit into the wall depending on what TV size you have.

Step 2
Unscrew the plate at the back of the TV and connect all required wire connections from the wall, through the square cable hole to the TV, then screw back the plate securely to ensure all the connected wires are going through the square cabling hole are not pinched or broken.

Step 3
Fix your mounting plate into place with the screws provided.

Step 4
Once you have checked that the TV is functioning correctly and all cables are fitted, apply an unbroken bead of silicon to the inside of the TV bezel at least 5 mm thick.

Step 5
Please ensure the bezel is firmly sealed to the wall surface to complete the waterproof properties of the installation. If it is not sealed correctly this will void your warranty.

Illustration of the Interface

24″/32″

1. DC 12V
   DC input.

2. OPTICAL
   Connecting for the OPTICAL signal.

3. RJ45
   Connecting for RJ45 signal.

4. HDMl1
   Connecting for HDMI signal.

5. COMPONENT/AV IN(YIV)IPBIPR
   Connecting for the COMPONENT/AV IN(Y/V)/PBIPR Input in Component mode.

6. RILAUDIO IN
   Connecting for the audio output jacks on your Camcorder or DVD.

7. TV
   Connected to an external antenna to receive the ATV/DTV program in ATV/DTV mode.

8. HDMl2
   Connecting for HDMI signal.

9. USB
   Connecting for USS signal.

10. EARPHONE
    Connecting for headphones.

Note: The product and illustrations in this user’s manual is only for explanation purposes and may vary depending on the model.

Remote Control Unit

1. POWER: Turn the TV on and off.

2. INPUT: This button is used to switch among different sources, Select a source and press ENTER button to confirm.

3. Digital Buttons(0-9, •): Directly select channels with digital buttons.

4. CH RTN: Switch to the previous program.

5. YouTube: If the network connects, press this key to view YouTube directly.

6. LIST: Press it to show channel list and favorite list on the screen.

7. HOME: Press it to go to the App home page.

8. NETFLIX: If the network connects, press this key to view NETFLIX directly.

9. Q.MENU: Press this key to go to the quick menu.

10. MENU: Display the main menu or exit the current menu.

11. ENTER: Validation key.

12. Arrow buttons : Use to select on-screen menu items and change menu values.

13. BACK: Return.

14. EXIT: Exit the menu.

15. COLOR BUTTONS: It’s used as it’s shown in the EPG or Program Edit menu.

16. VOL+/-: Press these buttons to adjust the volume.

17. MUTE: Press this button to cut off the sound of the TV set temporarily, press again to resume.

18. ZOOM: Press this button to select the aspect ratio of the screen.

19. CH T: Press these buttons to change the channel upward or downward.

20. DIGITAL MEDIA PLAYER CONTROL BUTTON: Include play/pause, stop, previous, next, backward, forward is used in USB mode.
    No record function. Please refer to relevant instructions in the section of multimedia player.

21. INFO: Display the program information.

22. MTS/AUDIO: In USB mode, press this button to switch the audio track when the movie is playing. In TV mode, press this button to switch MTS or Audio Language.

23. PICTURE: Press this button to select among Sports, Normal, Mild, User.

24. SOUND: Press this button to select among Standard, Sports, Movie, Music, User.

25. CC: Display CC function menu in TV/AV mode.

Menu Operation

1. Input Setup
   Press the INPUT key on the remote control to enter the “INPUT SOURCE” menu. Use the key to select an input source and press ENTER key to confirm.

Channels Selection

There are four ways to select a channel:

1. Use number keys, and “ENTER” keys on the remote control to select a channel directly.
   To select channel 90, press
   When you use the number buttons, you can directly select channels that were either erased or not memorized.

2. Use CH A/ v key on the remote control or on your TV to select a channel.
   When you press the CH A/ v key, the TV changes channels in sequence. You will see all the channels that the TV has memorized.
   You will not see channels that were either erased or not memorized.

3. Press CH RTN key to return to the previous channel, press it again to return to the current channel.
   To quickly switch between two channels that are far apart, tune to one channel, then use the number keys to select the second channel. Then use the CH RTN button to quickly alternate between them.
   CH RTN is not activated if no channel has been changed after the TV turns on.

4. Select channels from “Channels List” or “Favorite List”. Press the “ENTER” key to choose from the “Channel List” menu.

Volume Adjustment and Mute Setup

Volume adjustment
Press VOL+/ – key on the remote control or the TV to display the “Volume” menu, adjust the volume of the TV between Oto 100 by using VOL+/ -key:

• To increase the volume, press VOLD. key;
• To decrease the volume, press VOL ‘v key;

Mute
Press “MUTE” and the sound cuts off. The MUTE icon will appear in the lower-left corner of the screen.
To resume sound, press the “MUTE” button again, or simply press the VOL.6. key.

Current Channel Information
Press the “INFO” key on the remote control to view current channel information, the indications of channel information are listed in the following table.

Press “EXIT” key on the remote control to exit this OSD.

Picture

1. Press the MENU key to display the main menu on the screen.
2. Press key to select the “Picture” option.
3. Press the key to enter the “Picture” submenu.
4. You can also press the PICTURE key on the remote control to select one of the picture settings.

Picture Mode
Your TV has four picture settings (Sports, Normal, Mild, User) that are preset at the factory. Only “User” mode can be set to your preference by adjusting particular items such as Contrast, Brightness, Color, Sharpness.

1. Press  key to select the “Picture Mode” option.
2. Press  key to select one picture mode.

User settings for PICTURE (Contrast, Brightness, Color, Sharpness, Tint)
Your set has several settings which allow you to control picture quality.

1. Press key to select a particular item.
2. Press key to decrease or increase the value of a particul item.
3. Note: The adjusted values are stored according to the selected particular item.

Contrast: Adjusts the lightness and darkness between objects and the background.
Brightness: Adjusts the brightness of the picture.
Color: Adjusts the colors, making them lighter or darker.
Sharpness: Adjusts the outline of objects to either sharpen them or make them duller.
Tint: Adjust

Backlight
You can change the brightness of the entire screen according to your preference.

1. Press   key to select the “Backlight” option.
2. Press the key to increase or decrease the backlight value.
   Backlight: Adjusts the brightness of the whole screen

Color Temperature
You can change the color of the entire screen according to your preference.

1. Press  key to select the “Color Temperature” option.
2. Press  key to select one color temp.

Cool: Makes whites bluish.
Standard: Makes whiles nature
Warm: Makes whites reddish.

Sound

1. Press the MENU key to display the main menu on the screen.
2. Press  key to select the “Sound” option.
3. Press the key to enter the “Sound” submenu.
4. You can also press the SOUND key on the remote control to select one of the sounds.

Sound Mode

You can select the type of special sound effect to be used when watching a given broadcast.
Your TV has five sound settings (“Standard”, “Music”,”Movie”, “Sports”,”User’) that are preset at the factory.

1. Press  key to select the “Sound Mode” option.
2. Press  key to select one sound mode.

• Standard: Selects the normal sound mode
• Music: Provides clear and live sound for music.
• Movie: Provides live and full sound for movies.
• Sports: Emphasizes bass over other sounds.
• User: Selects your custom sound settings

Balance
If the volumes of the left speaker and the right speaker are not the same, you can adjust the
“Balance” to suit your personal preference.

1. Press key to select the “Balance” option.
2. Press key to decrease or increase the value of the item.

AVL
Each broadcasting station has its own signal conditions, and it is inconvenient to adjust the volume every time the channel is changed. “AVL” automatically adjusts the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.

1. Press  key to select the “AVL” option.
2. Press  key to select “On” or “Off.

Surround sound
This is used to turn on surround sound to gain better sound effects.

1. Press  key to select the “Surround sound” option.
2. Press  key to select “Surround” or “Off’.

Video Description

1. Press  key to select the “Video Description” option.
2. Press  key to select “on” or “Off’.

Sound

Digital Audio Output
This is used to set digital audio output.

1. Press  key to select “Digital Audio Output” option.
2. Press  key to select uAuto” or “PCM”

Audio Language
You can set the first and secondary language for audio.

Dolby Audio Process
This is used to set Dolby Audio Process.

1. Press  key to select the “Dolby Audio Process” option.
2. Press the key to enter the “Dolby Audio Process” submenu.

HDMIARC
Turn on or turn off the HDMI ARC function.

Function

1. Press the MENU key to display the main menu on the screen.
2. Press key to select the “Function” option.
3. Press the key to enter the “Function” submenu.

Noise Reduction

Press key to select the Noise Reduction mode. You can select the right model to match the pictures.

MPEG Noise Reduction
Press key to select the mode: off/low/middle/high. The picture will be better when it is in “high” mode.

Aspect Ratio
1. Press key to select ·Aspect Ratio” option.

2. Press key to change the size of the picture on the screen.

Vudu Deactivate
Log out of your Vudu user account.

TTS
Select TTS item and enable TTS setting.

Link Setup

1. Press  key to select the “Link Setup” option.
2. Press OK or key to enter the “Link Setup submenu.

Enable Link: Press to turn on/off the link setup.
Auto Power On: When this option is “On” the TV is in standby mode. To turn on the DVD can also turn the TV at the same time.
Auto Standby: When this option is “On” and the TV is on, to turn off the TV can also turn the DVD into standby mode.
Netflix Deactivate

1. Press key to select the “Netflix Deactive” option.
2. Press” the “ENTER” key to confirm.
3. Press “Yes” to confirm again, the Netflix will be activated.

Netflix ESN
Display the Netflix Esn information.

Netflix Version
Display the Netflix version.

Time

1. Press MENU key to display the main menu on the screen.
2. Press  key to select “Time” option.
3. Press key to enter “Time” submenu.

Off Time
In the “Off Time” item, press the button or ENTER button to enter the submenu, set the day & time to turn off the TV set.

On-Time
In the “On Time” item, press the button or ENTER button to enter the submenu, set the time to turn on the TV set, when the TV set is in standby mode. You can also choose which day to control your TV set in a week.

Sleep Timer

1. Press  key to select the “Sleep Timer” option.
2. Press  key repeatedly until the desired time appears

On-Time Sleep Timer Auto Sleep Auto Sync Clock
timezone(Off, 10mins, 20mins, 30mins, 60mins, 90mins, 120mins, 180mins, 240mins).
Notes: The sleep timer you have set will be canceled when the TV turns off or if a power failure occurs.
Notes: When the time is less than 60 seconds, reminder information will be displayed on the screen.
Press any key button to cancel the timer function.

Auto Sleep
Press key to select whether to open the No signal Power off features. If this function is opened, the TV will power off in ten minutes when there is no signal.

Auto Sync
You can modify the time of your TV set in Manual mode. In Auto Mode, the “clock” is decided by the DTV signal.

Clock–:–
When Auto Sync is on, the clock is got from DTV streams; Set the clock when Auto Sync is off.

Time Zone
You can choose it to modify your time zone in the TV set.

1. Press  key to select the “Time Zone” option.
2. Press  key to select a time zone.

Option

1. Press MENU key to display the main menu on the screen.
2. Press   key to select “Option” option.
3. Press key to enter the “Option” submenu.

OSD Language

1. Press  key to select the “OSD Language” option.
2. Press ENTER or key to select a proper language for OSD

OSD Time
Set the preferred amount of time for the OSD to be displayed on the screen.

Closed Caption

1. Press  key to select the “Closed Caption” option.
2. Press  key to select CC mode.

Reset

1. Press   key to select the “Reset” option.
2. Press the” ” or “ENTER” key to confirm.
3. Press “Yes” to confirm again, TV will turn off automatically and change all settings to factory settings.

Network Configuration
Please refer to “Network setting” behind.
Software Update(USB)
When the TV needs to be updated, please copy the new software to a USB storage and inset the USB storage to TV, then operate by following steps.

1. Press the key to select the “Software Update” option.
2. Press the **** or “ENTER” key to confirm.
3. Press “Yes” to confirm again, the TV will update by USB, Please wait a few minutes and don’t turn off the power, it will turn off automatically when updating is finished.

View End-User License

1. Press  the key to select the “View End-User License” option.
2. Press the key to enter the “View End-User License” submenu.

Lock
The”Lock” feature automatically locks out programming that is deemed inappropriate for children.
The user must first enter a Password before any of the lock restrictions can be set up or changed.

1. Press  key to select the “Lock” option.
2. Press ENTER or key to enter the “Lock” submenu, “Enter Password” menu will appear, enter your 4-digit password to enter “Lock submenu (the default and universal password is 1980).

Lock System

Set the Lock function on or off.

1. Press  key to select the “Lock System” option.
2. Press  key to select “On” or “Off.

Set Password

1. Press  key to select the “Set Password” option.
2. Enter your 4-digit password to enter enter “Set Password” submenu. Choose any 4-digits for your new password and enter them. As soon as the 4 digits are entered, the cursor skips to the “Confirm Password” item, re-enter the same 4 digits, and your new password has been memorized.

When the program is locked, you can also press the menu key, Info key, and so on. Then you can press key to call back the input-password window.

USA TV

1. Press  key to select the “USA TV” option.
2. Press ENTER key to open the USA TV menu.

USAMBARA

1. Press  key to select the “USA MPAA” option.
2. Press ENTER key to open the USA MPAA menu.

Canada English

1. Press  key to select the “Canada English” option.
2. Press ENTER key to open the Canada English menu.

Lock

Canada French

1. Press key to select the “Canada French” option.
2. Press ENTER key to open the Canada French menu.

RRT Setting

1. Press key to select the “RRT Setting” option.
2. Press ENTER key to open the RRT Setting menu.

RRT Reset

1. Press  key to select the “RRT Reset” option.
2. Press ENTER key to open the RRT Reset menu.

Channel
Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the TV (i.e. an antenna or a cable system).

1. Press  the MENU key to display the main menu on the screen.
2. Press key to select the “Channel” option.
3. Press ENTER or key to enter the “Channel” submenu.

Antenna

1. Press  key to select the “Antenna ” option.
2. Press ENTER or key to select a proper model for Antenna.

Auto-Search

1. Press  key to select the “Auto Search” option.

2. Press or ENTER key to confirm. then a notification window will be displayed on the screen.
   Select “Start” to start search or “Cancel” to cancel it.
   When searching, press the EXIT key to exit tuning at any moment. Press the MENU key to skip DTV tuning when searching DTV, skip ATV tuning when searching ATV.

3. After all the available channels are stored, the searching menu will exit.

Program Edit
After the program is searched, select “Program Edit” in the “Channel” menu, press the “ENTER button, the program can be edited such as delete or skip according to the user’s habit.

Channel
Skip (Blue) Button
This function can help shield certain programs.
The program skips when selecting the program by the button on the TV or remote control.

1. Select the program to be shielded in the”Program Edif.
2. Press the “Skip” (Blue) button, the skip mark is displayed at the left side of the program and this program is shielded.
3. To cancel the Skip function, enter the channel edit menu, select the shielded program, and press the “Skipfl (Blue) button, the skip mark at the left side of the program disappears then the program is recovered.

Delete (Red) Button
This function can help delete programs.

1. Select the program to be deleted in the “Program Edit”.
2. Press the “Delete”(Red) button, the program will be deleted.

Favorite(Yellow) button
This function can help store the favorite program then these programs can be quickly selected.

1. Select the program which is your favorite.
2. Press the “Fav”(Yellow) Button, the favorite mark is displayed at the left side of the program and this program is stored in the Favorites.
3. To cancel the Favorite function, enter the program edit menu, select the program, and press the “Fav”(Yellow) button, the favorite mark at the left side of the program disappears.

DTV Manual Search
Enter a digital number and press “ENTER” to select DTV Channel.

ATV Manual Search

1. Press  key to select “ATV Manual Search” option.
2. Press or ENTER key to enter the submenu.

Current CH

1. Press  key to select the second item.
2. Press  key to select a current channel.

Fine-Tune

1. Press  key to select the third item.
2. Press  key to select a better frequency for the current channel.

Network Setting

1. Press the “Menu” to enter, then pitch on the “Option”, and press “ENTER” or click the right button to enter the submenu.
2. Pitch on the “Network Configuration”, and press “ENTER” or click the right button to enter the “Network Configuration”.
3. When the wired network is used, if select dynamic IP address setting, pitch on the “DHCP” in the “Network Configuration”, then click the “Setting”, and press the “ENTER” button to enter. If you select static IP address setting, pitch on the “Static” in the “Network configuration”, then setting up the IP, Netmask, Gateway, and DNS in sequence. When the setting is complete, pitch on the “setting” and press the”ENTER”.
4. If shows “Success”, the “WLAN” on the bottom right corner will turn to green from red, and it means the network connect successfully; If shows “Fail”, it means the network can not connect, please check whether the net wire and router connect successfully or not.
5. Select the “WIFI” in the Network Configuration before using WIFI connecting.

Pitch on the “Setting”, press the “ENTER” to confirm.
If shows “Success”, the “WIFI” on the bottom right corner will turn to green from red, and it means the network connects successfully; If shows “Fail”, it means the network can not connect, please check whether the wireless router connects successfully or not.

Internet

Press the “HOME” key to enter the internet interface

NETFLIX

1. Use the arrow key to Select the button, then press the ‘ENTER’ key to enter NETFLIX.
2. Use the arrow button to select one video and press the -ENTER” key to play. Press the ‘MENU’ key to exit playing.
3. Use the arrow key to browse the pages. Press the “MENU” key to return to main menu and press the “EXIT” key to exit.

Youtube

Youtube

1. Use the arrow key to the Select button, then press the “ENTER” key to enter Youtube.
2. Use the arrow button to select one video and press the “ENTER key to play. Press the “MENU” key to exit playing.
3. Press the key to open or close the control menu when playing.
4. Press key to enter search interface, input the keywork and then press -0K- to search videos.

VUDU

1. Use the arrow key to select the  button. then press the “ENTER” key to enter the VUDU application.

PANDORA

1. Use the arrow key to the Select button, then press the “ENTER” key to enter the PANDORA application.

Twitter

1. Use the arrow key to the Select button, then press the “ENTER” key to enter Twitter.
2. Input the right Email and password, then select the “Authorize app” button and press the “ENTER” key to log in.
3. Use the arrow key to browse the pages. Press the “MENU” key to return to the main menu and press the “EXIT” key to exit twitter.

Red key: log in or log out of Twitter. Green key: refresh the current page. Yellow key: write a new tweet.
Blue key: Search tweet.

Facebook

1. Use the arrow key to Selectbutton, then press the “ENTER” key to enter Facebook.
2. Visit https://www.facebook.com/device on your smartphone or computer and enter this code:
3. Press an arrow key to browse the pages and press the “ENTER” key to view.
   Press the “MENU” key to return the main menu. Press the “EXIT” key to exit Facebook.
   Red key: log in or log out of Facebook. Green key: refresh the current page.
   Yellow key: sign “like” or “unlike” for current content. Blue key: view comments and add comments.

Accuweather

1. Use the arrow key to the Select button, then press the “ENTER” key to enter Accuweather.
2. Input a city or zip code press select to get the weather information.

Screencast
Use the arrow key to the Select button, then press the “ENTER” key to enter Screencast.

Digital Media Player

Introduction This TV is embedded with one USB port digital media player. It can find the devices that support USB1.1/2.0, including flash disk, USB hard disk and digital camera. It supports functions as Displaying pictures. Play music files, Display text files.
Notice:

1. In order to avoid affecting the user’s viewing experience, please use better quality and shorter USB cable.
2. Play, preview some of the non-standard files that may appear abnormal, please understand.

Explain

1. Under the USB channel, you can use only the remote control.
2. Play Control menu to enter the playing surface to press the menu button pop-up menu

Troubleshooting

•The wrong input source is selected.
•The input source has failed to connect with the TV or is not turned on.| •Plug the power adapter into a suitable outlet. Try both the 12/24V & 240V adapters
•Select the correct input source.
•Make sure the input source is correctly connected and turned on.
No sound.| •The volume control is set to a minimum.
•The mute button on the remote control has been pressed
•An incorrect sound system mode is set.| •Press the is button to increase the volume.
•Press  or the (or ) button to restore/increase the volume.
•Set a correct sound system mode from the main menu to match your TV source.
No picture, or monochrome picture only.| •The color system setting does not match the program.
•The sound system setting does not match the program.| •Select the appropriate color system setting.
•Select the appropriate sound system setting. (If unsure, use Auto settings where available).
Sound or picture interference.| •Some equipment that causes interference is close to the TV.
•More than one device is plugged into the same power outlet.
•An incorrect sound system mode is set.| •Keep interference-causing equipment away from the TV.
•Plug the power adaptor into another, separate power outlet.
•Set a correct sound system mode from the main menu to match your TV source.
PVR recording failed, or”DISK NOT READY” is displayed.| •You may not have removed your USB device after the last recording, which is necessary to protect the device from damage.| •Remove the USB device after each recording, if you experience recording problems. If”DISK NOT READY” is displayed, remove the device, reconnect and then proceed with your recording.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>