Uthfy ATF-014L Tower Fan Instruction Manual

: June 15, 2024
: Uthfy

Table of Contents

PRODUCT STRUCTURE
FEATURE
Assembly
ASSEMBLING
FUNCTIONS & OPERATION
REMOTE CONTROL
CLEANING AND MAINTENANCE
ACCESSORY
TECHNICAL SPECIFICATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**Uthfy ATF-014L Tower Fan Instruction Manual

**

WARNING

Use as per the rating voltage.
Do not repair or remake the appliance by yourself, it should be repaired by the repairmen.
Do not operate the appliance with wet hands, in order to avoid damage.
If the supply cord is damaged, it must be replaced by a same cord from the manufacturer or its service agents.
When the appliance is not in use, switch it off and unplug it.
Do not insert things to air outlets and inlets, in order to avoid damage
Do not use the appliance near explosive and combustible gas.
Use the appliance only on a flat surface.
Do not use outdoors.
Do no turnover the appliance. Unplug the power supply If it is toppled over and there have some water in the body. Dry the body before use
Clean the appearance with a lightly damp cloth.It can clean with neutral detergents. Do not rinse with water.
Do not make air outlets and inlets near the wall or curtain
Do not knock or shake the body when use, otherwise it may cause stop
The appliance must not located immediately below a socket outlet
The rating current of socket should exceed 10A.
Do not use the appliance in the immediate surrounding of a bath,a show or a swimming pool.
This appliance is not intended for use by persons including children with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance:

PRODUCT STRUCTURE

Product Overview

A. Control Panel & Display
B. Wind outlet
C. Front frame
D. Base
E. Handle
F. Wind inlet
G. Back frame

FEATURE

Control Panel and Display

Remote control

Assembly

Assembly Instruction

ASSEMBLING

Step 1: Aiming the assemble poles with the corresponding holes, and insert the poles into the holes. It need 8pcs screws.
Step 2: Aiming the assembled base to screw poles of the fan body
Step 3: After well connect of the body and base, screw into the screw holes of the base. And put the power cord into the slot of the base.
Step 4: Put the fan flatly

FUNCTIONS & OPERATION

Place the unit on a firm level surface and plug it into a socket. Power indicator light reminding this products in standby mode and room temperature displays.

Turn on button ,default setting is in medium speed, Turn it again, products in standby.

To end operation, press once.

This button allows you to select between Low (1) , Medium (2) or High speeds.
The relevant icon will be displayed on screen when selected.

Activates the oscillating function. Simply press once to start. swing indicator light is on.Press again to cancel the function.

This button allows you to enter the ‘timer mode’. Press to increase the number of hours (01,02 to 12) you wish the Fan to remain operational. Timer indicator light is on. Press it to “00” to cancel the timer function.

Press it to light On/Off the display.

REMOTE CONTROL

The remote control uses on button cell battery, type CR2025(3V).To remove the battery carriage use your thumb to squeeze the release tab to the right and then pull the carriage out. Place the battery into the carriage and slide the carriage back into the remote. We recommend the use of a Lithium-ion battery for longer use.
NOTE: Follow battery disposal instruction on battery packaging, or contact your local safety council for safely disposal of batteries.

Before using the remote control, you must remove the insulating film as shown in picture below.
All functions performed with remote control work identically to the unit control panel.

Note: Please follow battery disposal instruction on battery packaging, or contact your local councils for safely disposal of batteries.

CLEANING AND MAINTENANCE

Clean with neutral detergent and soft cloth.
Attention: unplug the power plug when clean the appliance ,since there have high pressure in the body. Do not leave any water on the control panel.

A loose fit between the AC outlet and plug may cause over heating of the plug. If the plug over heats, it might cut off the fuse inside the power cord plug.

If your fuse access cover is located on the side of the plug:

Grasp plug and remove from the receptacle or other outlet device. Do not yank the cord to unplug.
Select a suitable tool such as a small flat screwdriver or travel scissors.
Toopen the fuse cover. Slide open fuse access cover on top of attachment plug toward blades. (see fig.1)
Carefully remove the fuse by prying it out. (see fig.2)
Risk of fire can result by using wrong fuse rating. Replace fuse only with 5 Amp, 125 Volt rating.
Toclose the fuse access cover. Slide to close access cover on top of attachment plug. (see fig.3)

If your fuse access cover is located on the face of the plug:

Grasp plug and remove from the receptacle or other outlet device. Do not yank the cord to unplug.
Select a suitable tool such as a small flat screwdriver or travel scissors. 1NN
Toopen the fuse cover. Press the tool down, and then 1 R7 <) pry the protection door off of the face of the plug. (see 2 0) fig. #1).
Continue to remove protection door until you can access the fuse below. (see fig. #2)
Carefully remove the fuse by prying it out.
Risk of fire can result by using wrong fuse rating.
Replace fuse only with 5Amp, 125 Volt rating.
Toclose the Close fuse cover. Push the protection door back onto the face of the plug and press it securely in place.