GOWIN DK-START-GW1NSR2 Development Board User Guide
- June 6, 2024
- GOWIN
Table of Contents
DK-START-GW1NSR2 Development Board
User Guide
Figure 1 PCB Components
Kit List
Figure 2 Development Board Kit
Introduction
Thank you very much for taking DK-START-GW1NSR2 as the development & learning platform. This user guide can help you install the required software, compile the Demo, and download it to the development board to test so as to be familiar with the development flow.
Install Software
Install Gowin EDA software (Gowin YunYuan Software) to create, compile and download the FPGA Demo program. Download the EDA software, apply for a license, and obtain the software user guide at the GOWINSEMI website https://www.gowinsemi.com/en/support/home/. For details on the software installation method and usage, please refer to SUG100, Gowin YunYuan Software User Guide.
Development Board Power-on Test
The test program has been downloaded into the internal FLASH before the
delivery of the DK-START-GW1NSR2 development board. The development board can
be checked whether to work when it is powered on.
Connect the J6 (USB interface) of the development board to the PC using the
USB cable. If the loading is done, two green LEDs will blink in turn,
indicating that the development board can work.
Compile Demo Program
The LED test program is to demonstrate two LEDs blinking. Users can download
the corresponding demo at the Gowinsemi website:
https://www.gowinsemi.com/en/support/database/. Save the project in the
directory with no Chinese characters. Open and compile this demo using Gowin
YunYuan software.
-
Open the “LED_test.gprj” project and the following are displayed in the “Design” window:
• GW1NSR-LX2CQN48PC6/I5: Gowin FPGA device part number;
• gowin_emcpu.v，ledtest_top.v: Verilog code;
• latest.CST: Physical constraints file.
Figure 3 Design
-
Right-click “Place & Route” in the “Process” window and select “Rerun All”.
Figure 4 Select Rerun All
-
After compilation, the following information will be displayed. The bitstream file is generated.
Figure 5 Compiling Completed
Download and Run
-
Connect the JTAG(J6) on the development board with the PC using the USB cable. Switch the SW3~SW6 to the FPGA side. Double-click on the “Program Device” in the “Process” window. The “Programmer” window will pop up. Right-click on the device list, and select “Configure Device”. The Device configuration dialog box will pop up.
Figure 6 Programmer
-
Set the download mode as shown below and specify the bitstream file path.
Figure 7 Device Configuration
-
After configuration, click the “Program/Configure” to download the program.
Figure 8 Program/Configure
Finally, download led.bin of MCU. Please refer to IPUG515, GW1NS-2C_MCU Quick Design Reference Manual. After finishing, four LEDs of the development board will blink in turn.
Support and Feedback
Gowin Semiconductor provides customers with comprehensive technical support.
If you have any questions, comments, or suggestions, please feel free to
contact us directly in the following ways.
Website: www.gowinsemi.com
E-mail:support@gowinsemi.com
Tel: 00 86 0755 82620391
Revision History
| Date | Version | Description |
|---|---|---|
| 02/27/2020 | 1.0E | The initial version published. |
Copyright© 2020 Guangdong Gowin Semiconductor Corporation. All Rights
Reserved.
No part of this document may be reproduced or transmitted in any form or by
any denotes, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written consent of GOWINSEMI.
Disclaimer
GOWINSEMI®, LittleBee®, Arora, and the GOWINSEMI® logos are trademarks of
GOWINSEMI and are registered in China, the U.S. Patent, and Trademark Office,
and other countries. All other words and logos identified as trademarks or
service marks are the property of their respective holders, as described at
www.gowinsemi.com. GOWINSEMI assumes no liability
and provides no warranty (either expressed or implied) and is not responsible
for any damage incurred to your hardware, software, data, or property
resulting from usage of the materials or intellectual property except as
outlined in the GOWINSEMI Terms and Conditions of Sale. All information in
this document should be treated as preliminary. GOWINSEMI may make changes to
this document at any time without prior notice. Anyone relying on this
documentation should contact GOWINSEMI for the current documentation and
errata.
References
- 📧support@gowinsemi.com
- Home|GOWIN Semiconductor
- One moment, please...
- Documentation Database | Support | GOWIN Semiconductor Corp.
- GOWIN EDA | GOWIN Semiconductor
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>