OPPSK2024322 18x18W Outdoor Waterproof LED Par Light User Manual

Table of Contents

Specifications:

Unpacking Instructions:
Carefully unpack the product immediately and check the container to ensure all parts are present and in good condition.

Caution:
Do not open the housing or attempt repairs yourself. Contact us at info@oppsk.com for service.

Introduction

Product Overview & Size:
The LED Par Light may be mounted in any position; ensure adequate ventilation around the product.

Setup

AC Power:
The LED Par Light has an auto-ranging power supply with an input voltage range of 110 to 240 VAC, 50/60 Hz. Refer to the product’s specifications chart for power requirements.
Mounting:
Before mounting, follow safety recommendations. Mount the light in any position with proper ventilation.

Operation

Control Panel Operation:
Access functions using the four buttons below the display. Use buttons to select modes, scroll options, and activate menu items.
System Menu Display Mode:
Different modes available for color mixing, jumping, gradient, manual dimming, and more. Refer to the manual for detailed operation instructions.

FAQ:

Q: Can I adjust the color and brightness of the LED Par Light?
A: Yes, the light offers various manual dimming options and color mixing modes that allow you to customize the color and brightness according to your needs.
Q: Is it safe to use the LED Par Light outdoors in rainy conditions?
A: To prevent electrical shock or fire risk, avoid exposing the fixture to rain or moisture. Ensure the housing is not visibly damaged before outdoor use.

18x18W Outdoor Waterproof
LED Par Light User Manual

What In the Box:

Carefully unpack the product immediately and check the container to make sure all the parts are in the package and are in good condition.
Caution
- There are no user serviceable parts inside the fixture. Do not open the housing or attempt any repairs yourself. In the unlikely situation, your unit may require service, please contact us: info@oppsk.com
Disclaimer:
- OPPSK believes that the information contained in this manual is accurate in all respects. However, OPPSK assumes no responsibility and specifically disclaims any and all liability to any party for any loss, damage or disruption caused by any errors or omissions in this document, whether such errors or omissions result from negligence, accident or any other cause. OPPSK reserves the right to revise the content of this document without any obligation to notify any person or company of such revision, however, OPPSK has no obligation to make, and does not commit to make, any such revisions.

Please keep this User Manual for future consultation.
Unpack and check carefully there is no transportation damage before using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Maximum ambient temperature is Ta : 104℉/40℃. Don’t operate it where the temperature is higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the LED light while the fixture is on.

Product Overview & Size

AC Power :
The LED Par Light has an auto-ranging power supply and it can work with an input voltage range of 110 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. The listed current rating indicates the product’s average current draw under normal conditions.
Mounting:
Before mounting the product, read and follow the safety recommendations indicated in the. Safety Introductions.
Orientation:
The LED Par Light may be mounted in any position; however, make sure adequate ventilation is provided around the product.

Control Panel Operation:
To access the control panel functions, use the four buttons located underneath the display.

Button	Function
	Select an operation mode or back out of the current menu option
	Scroll up the list of option or select a higher value
	Scroll down the list of option or select a lower value
	Activate a menu option or a selected value

$OPPSK2024322-18x-18W-Outdoor-Waterproof-LED-Par-Light- $3$$

display mode	function declaration
A001(A001-A512)	address code
CHND (6CH/10CH)	6/10channelmode
CL01 (CL01 CL32)	Static color mixing mode (32 kinds)
CC99 (CC01-CC99)	Jump mode
EE99 (EE01-EE99)	Mutation pattern
FF99 (FF01-FF99)	Gradient mode
ST99 (ST01-ST99)	Confirm FM flash color (32 kinds)
SOU1(SOU1/2/3/4)

Voice control mode SOU1 voice control jump SOU2 voice control mutation
SOU3 voice-controlled color-changing stroboscopic Sou4 vice control jmp+mutation+color change strobe

Remarks:

ln A001mode,press the confirmation key to aromatically enter the current adjustment mode, the up and down keys to adjust the value, and the confirmation key to adjust the color, After the parameters are adjusted, press the menu key to reteam, and press the confirmation key to adjust the machine.
This version supports RDM function.

DMX Mode :