idinio 140305 Zigbee LED Dimmer Module User Guide

June 6, 2024
idinio

idinio 140305 Zigbee LED Dimmer Module User Guide

idinio 140305 Zigbee LED Dimmer Module

Installation


FIG 1 Installation

Turn off the power of the specific power group in the fuse box and double check if the existing wall dimmer is really turned off.

FIG 2 Installation

FIG 3 Installation

FIG 4 Specification

Compatible Load Types

FIG 5 Compatible Load Types

ZigBee AC phase cut dimmer based on the latest ZigBee 3.0 protocol. 220V-240V AC Input and Output Voltage. Supports resistive loads
and capacitive loads. Trailing edge control. Enables to control ON/OFF and light intensity of connected triac dimmable led light or led
driver. ZigBee end device that supports Touchlink. Can directly pair to a compatible ZigBee remote via Touchlink without a hub. Supports
self-forming zigbee (mesh) netvvork without a hub and add other devices to the network Supports find and bind mode to bind a ZigBee
remote. Radio Frequency : 2.4GHz

ZigBee Clusters which are supported by this device are as follows:

Input Clusters

• OXOOOO: Basic • Identify • Groups • Scenes • on/off. Level Control • OxOb05: Diagnostics
Output Clusters  • Ox0019. OTA

Network Pairing

Operation
This ZigBee device is a wireless receiver that communicates with a variety ofZigBee compatible systems. This receiver receives and is  controlled by wireless radio signals from the compatible ZigBee system.

Zigbee Network Pairing through coordinator or hub (being added to a Zigbee Network)

Remove the device from a previous zigbee network When it already has been paired before, otherwise pairing will fail. Please refer to the part “‘Manual Factory Reset””.

From your ZigBee controller or hub interface: choose to add a lighting device and enter Pairing mode as instructed by the controller.

Double Press the reset button to activate the network pairing mode (the blue indicator light is flashing) and the network pairing mode will last for 15 minutes. After a timeout repeat this step.

The Blue indicator will stop flashing and solid on for IOS then the device will appear in your controllers menu and can be controlled through controller or hub interface.

TouchLink

TouchLink to a Zigbee Remote

Short press “Reset” button 4 times.

The Green indicator will start flashing to show that the device is in touchlink commissioning. When after 180s a timeout occurs repeat this step.

Bring the remote or touch panel within 10cm of the lighting device.

Set the remote or touch panel into Touchlink commissioning, please refer to the corresponding remote or touch panel manual how to do this.

The connecting lights will start flashing to indicate the pairing is in process. Once both are paired the connected lights and the green indicator light will stop flashing and you can than control the lights with the remote.

Note:

  1. Directl Touchlink (both devices are not added to a Zigbee network). Each device can link with I remote
  2. Touchlink after both devices are already added to a Zigbee network Each device can link with max30 remotes.
  3. For Hue Bridge & Amazon Echo Plus, add the remote and the device to the Zigbee network first then activate Touchlink
  4. After the Touchlink connection succeeded the device can be controlled by the linked remotes.

Remove the device from a zigbee network.

Short press the reset button 3 times, the purple indicator light will start flashing. The purple indicator will stop flashing and become solid for 10 seconds to show that the device has been successfully removed. When after 180 seconds a timeout occurs repeat this step.

Press and hold the reset button for over 5 seconds.

The Red indicator light will be on for 10 seconds to show the reset has been successful

Note: All configuration settings will be erased when the device has been reset or removed from the network.

Find and Bind mode

Note: Make sure the device and remote are already added to the same Zigbee network.

Press the reset button 5 times.

The yellow indicator will start flashing. When after 180 seconds a timeout occurs repeat this step.

Set the remote or touch panel (target node) into find and bind mode and enable it to find and bind the initiator, refer  to corresponding remote or touch panel manual for instructions.

The remote or touch panel will indicate that the device was connected successfully and can now be controlled and programmed.

Setup Zigbee Network

Setup a Zigbee network & add other devices to this network (no hub required).

Press the reset button for 6 times to enable the device to setup a Zigbee network.

The white indicator will start flashing and stay solid for 10 seconds to show that the dimmer has successfully created the Zigbee network.

Press the reset button for 7 times to allow other devices to be added to the Zigbee network.The red indicator light will be flashing continuously.

Set a device (e.g. remote or touch panel) into network pairing mode and connect it to the network, refer to the corresponding remote or touch panel manual how to do this. This operation has a time limit of 180 seconds.
Repeat step 4 in case you want to connect more devices and remotes to the network, refer to their manuals.

Bind the added devices and remotes through Touch link so that the devices can be controlled by the remotes, refer to their manuals.

**Note:**

  1. Each added device can link and be controlled by max.30 added remotes.
  2. Please refer to remote manual on how many devices can be linked.

WARNING

Safety warning!
Ensure you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable). Keep this document for future reference and only use the product as described in this document. Any other use of the product than described in this manual may damage the product or cause injury to the user (e.g. due to a short circuit, fire or electric shock). Disconnect the product from the power source if problems occur. Do not drop the product and avoid bumping. Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. When a non-standard consumer (power)installation is required this should be performed by a qualified technician to reduce the risk of an electric shock. Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED) device during usage since it can generate heat causing damage. Besides LED can be extremely bright and may cause serious eye damage so don’t stare at it directly. When a product is meant for indoor and/or outdoor use only, this will be mentioned on the product/parts or in the manual. Keep the product out of reach of children or animals.

Cleaning and Maintenance warming !
Do not use cleaning solvents or abrasives. Do not clean the inside of the device. Do not attempt to repair the device when  the device does not operate correctly, replace it. Clean the outside of the device using a soft, damp cloth (don’t use microfiber cloth).

Support:
If you need further help or have comments or suggestions please visit www.shada.nl/nl/contact

The item should be disposed of separately from household waste The item should be handed in for recycling in accordance with local environmental regulations for waste disposal By separating a marked item from household waste, will help reduce the volume of waste sent to incinerators or land-fill and minimize any potential negative impact on human health and the environment.

This product carries the CE mark of certification, which confirms that this product meets EU safety, health and environmental protection requirements.

Hereby, Shada declares that the radio equipment type 140305 Zigbee LED Dimmer Module is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address: https://www.shada.nl/downloads

D.O.C: http://shada.nl/p/140303

FIG 30 QR Code

SHADA
Molenmakershoek 28, NL-7328 JK APELDOORN – The Netherlands
vwvw.shada.nl

FIG 29 Product Feature

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals