ESR 2C502 HalLock Magnetic Wireless Car Charger User Manual
- June 6, 2024
- ESR
Table of Contents
2C502 HalLock Magnetic
Wireless Car Charger
User Manual
Thank you for choosing ESE?!
Before using this product, please read this manual carefully. Keep this manual
for future reference.
Product Overview
Car Mounting Instructions
The charging pad is equipped with a magnetic ring. It will attach to phones to
ensure they stay securely attached to the charger (phone/case must have built-
in magnets to work properly with this charger).
-
Unscrew the nut from the socket.
-
Place nut around ball head with top facing clamp, then fully insert ball head into the socket.
-
Tighten the nut clockwise.
-
Attach the clamp to car vent.
-
Magnetically attach the phone to begin charging.
Indicator Light Guide
| Charger Status | Plugged In | Standby | Charging/Fully Charged | Error Detected |
|---|---|---|---|---|
| Indicator Light | On for 5 sec | Off | On | Flashing |
If an error is detected:
- Check that your phone supports wireless charging and does not have any credit cards, stands, or other metal attachments on the back (other than the magnetic ring).
- After checking the above, unplug and plug in the charging cable again to resume normal charging.
Important Reminders
- For maximum charging speed, use a cable and adapter compatible with QC (Quick Charge) 2.0/3.0 or PD (Power Delivery) fast charging.
- This charger is not compatible with cases thicker than 5 mm.
Safety Warnings
- Do not attempt to disassemble the device, expose it to an open flame, or submerge it in water to avoid damaging the device.
- Do not expose the device to extremely hot, humid, or corrosive environments to avoid damaging the device.
- Always check for damage to the device, cables, or other accessories before using the device. If damaged, do not use the device.
- Do not expose the device to corrosive liquids, as they will seriously damage the device and void the warranty.
- Do not attempt to disassemble or modify the device in any way, as it may cause serious damage and void the warranty.
- Do not place the device in temperatures below 0°C (32°F) or above 60°C (140°F).
FCC ID: 2AP EW- 2C502
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1)This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/tv technician for help.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. this equipment should be installed and operated with a minimum distance of 20cm between the radiator &your body.
IQ 24790-2C502
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device.”
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>