idinio LDR01435 Zigbee LED Dimmer User Guide

idinio LDR01435 Zigbee LED Dimmer

Installation

Turn off the power of the specific power group in the fuse box and double- check if the existing wall dimmer is really turned on

Disassemble the old dimmer or switch.
Connect the power wires according to the wire diagram

Install the dimmer in the wall box and fix it with the 2 screws Turn on the power again in the fuse box and test the dimmer

Network  pairing

Operation

• ZigBee AC phase-cut dimmer based on the latest ZigBee 3.0 protocol. 220V-240V AC Input and Output Voltage. Supports resistive loads and capacitive loads. Trailing edge control. Enables to control ON/OFF and light intensity of connected Triac dimmable led light or led driver. ZigBee end device that supports Touch link. Can directly pair to a compatible ZigBee remote via Touchlink without a hub. Supports a self-forming Zigbee (mesh) network without a hub and add other devices to the network. Supports find and bind mode to bind a ZigBee remote. Radio Frequency:24CHz. ZigBee Clusters that are supported by this device are as follows: Input Clusters Ox0000: Basic.Ox0003: Identity:Ox0004: Groups.OxO005: Scenes.Ox0006:On/off Ox0008: Level Control OxOb05: Diagnostics Output Clusters OxO019.OTA
• This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This receiver receives and is controlled by wireless radio signals from the compatible ZiaBee system

Zigbee Network Pairing through coordinator or hub (being added to a Zigbee Network)

• Remove the device from a previous Zigbee network When it already has been paired before, otherwise pairing will fail. Please refer to the part “Manual Factory Reset”
• From your ZigBee controller or hub interface: choose to add a lighting device and enter Pairing mode as instructed by the controller
• Double Press the reset button to activate the network pairing mode (the blue indicator light is flashing) and the network pairing mode will last for 15 minutes. After a timeout repeat this step.
• The Blue indicator will stop flashing and solid on for 10s then the device will appear in your controller’s menu and can be controlled through controller or hub interface

Touch  Link

• TouchLink to a Zigbee Remote
• The Green indicator will start flashing to show that the device is in touch link commissioning. When after 180s a timeout occurs repeat this step,
• Bring the remote or touch panel within 10cm of the lighting device.
• Set the remote or touch panel into Touchlink commissioning, please refer to the corresponding remote or touch panel manual how to do this.
• Short press “Reset”‘ button 4 times.

The connecting lights will start flashing to indicate the pairing is in process. Once both are paired the connected lights and the green indicator light will stop flashing and you can than control the lights with the remote.

Note:

1. Direct Touchlink (both devices are not added to a Zigbee network) Each device can link with1remote.
2. Touchlinkaiter both devices are already added to a Zigbee network. Each device can link with max.30 remotes.
3.  For Hue Bridge & Amazon Echo Plus, add the remote and the device to the Zigbee network first then activate Touch link.
4. After the touchline connection is succeeded the device can be controlled by the linked remotes

Remove the device from a zigbee network

Short press the reset button 3 times, the purple indicator light will start flashing. The purple indicator will stop flashing and become solid for 10 seconds to show that the device has been succesfully removed. When after l80 seconds a timeout occurs repeat this step.

Manual Factory Reset.

• Press and hold the reset button for over 5 seconds.
• The Red indicator light will be on for 10 seconds to show the reset has been successful.
• Note: All configuration settings will be erased when the device has been reset or removed from the network.

Find And Bind Mode

•  Note: Make sure the device and remote are already added to the same Zigbee network.
•  Press the reset button 5 times.
•  The yellow indicator will start flashing. When after 180 seconds a timeout occurs repeat this step.
•  Set the remote or touch panel (target node) into find and bind mode and enable it to find and bind the initiator, refer to the corresponding remote or touch panel manual for instructions
•  The remote or touch panel will indicate that the device was connected successfully and can now be controlled and programs.

SetUp Zigbee Network

• Setup Zigbee network & add other devices to this network (no hub required)
• Press the reset button for 6 times to enable the device to set up a Zigbee network.
• The white indicator will start flashing and stay solid for 10 seconds to show that the dimmer has successfully created the Zigbee network.
•  Press the reset button for 7 times to allow other devices to be added to the Zigbee network. The red indicator light will be flashing continuously.
•  Set a device (eg. remote or touch panel)into network pairing mode and connect it to the network, refer to the corresponding remote or touch panel manual how to do this. This operation has a time limit of 180 seconds.
•  Repeat step 4 in case you want to connect more devices and remotes to the network, refer to their manuals.
• Bind the added devices and remotes through Touchlink so that the devices can be controlled by the remotes, refer to their manuals.

Warnings

Safety Warning

• Ensure you have fully read and understood the instructions in this document before you install or use the product following the installation/wire diagram (when applicable)
• Keep this document for future reference and only use the product as described in this document.
• Any other use of the product than described in this manual may damage the product or cause injury to the user (eg. due to a short circuit, fire or electric shock)
• Disconnect the product from the power source if problems occur.
• Do not drop the product and avoid bumping.
• Do not use the product if a part is damaged or defective.
• Replace a damaged defective product immediately.
• When a non-standard consumer (power)installation is required this should be performed by a qualified technician to reduce the risk of an electric shock.
• Make sure the product is sufficiently ventilated during use. Never cover an electrical (LED) device during usage since it can generate heat causing damage.
• Besides LED can be extremely bright and may cause serious eye damage so don’t stare at it directly.
• When a product is meant for indoor and/or outdoor use only, this will be mentioned on the product/parts or in the manual.
• Keep the product out of reach of children or animals

Cleaning And Maintenance Warning

• Do not use cleaning solvents or abrasives.
• Do not clean the inside of the device.
• Do not attempt to repair the device when the device does not operate correctly, replace it.
• Clean the outside of the device using a soft, damp cloth (don’t use microfiber cloth)

Support

lf you need further help or have comments or suggestions please visit www.shada.nl/nl/contact

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>