OKIN RF54 Wireless Remote Control Instructions

OKIN RF54 Wireless Remote Control

Button Of Remote

Click the ZG button, the actuator moves to ZG position, stop when click any button during the movement;
Press and hold the ZG button for 5s, timer LED of remote flashes, the control box records current position as ZG position;
When in the process of moving to memory positions, the head and foot actuators move first,

ZG button (button 10 in figure 1)

Click the ZG button, the actuator moves to ZG position, stop when click any button during the movement; Press and hold the ZG button for 5s, timer LED of remote flashes, the control box records current position as ZG position; When in the process of moving to memory positions, the head and foot actuators move first,

M1 button (button 4 in figure 1)

Click the M1 button, the actuator moves to M1 position, stop when click any button during the movement;

M2 button button 6 in figure 1

Click the M2 button, the actuator moves to M2 position, stop when click any button during the movement;

Head up button 7 in figure 1

Press and hold HEAD UP button of remote, head actuator moves out, stop when released 1.5 Head downbutton 8 in figure 1
Press and hold HEAD DOWN button of remote, head actuator moves in, stop when released

Foot up button 11 in figure 1

Pressa and hold FOOT UP button of remote, foot actuator moves out, stop when released;

Foot down button 12 in figure 1

Press and hold FOOT DOWN button of remote, foot actuator moves in, stop when released When moving to flat position, lumbar actuator and tilt actuator move first, after 500ms, head and foot actuators start moving;

Flat button 9 in figure 1

Click FLAT button, the bed goes flat, stop when click any button during the process of going

Massage head button 1 in figure 1

Click MASSAGE HEAD button, head massage motor switches massage intensity, massage intensityswitches among 0-1-2-3

Massage FOOT button 3 in figure 1

Click MASSAGE FOOT button, head massage motor switches massage intensity, massage intensityswitches among 0-1-2-3

Massage ON/OFF button 2 in figure 1

Click Massage ON/OFF button, if the massage motors are on, then it turns off massage motors, if massage motors are off, then it turns on the massage motors;

Massage Type button 5 in figure 1

Click massage type button, to switch the massage mode og massage motors, massage mode switches among type0type1type2type3type0; this button can only switch the massage mode, it can not open massage motors

FCC warning

Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by doing one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.

FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user`s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with ISED exposure compliance requirement, please follow operation instruction as documented in this manual.

ISED RSS Warning: This device complies with Innovation,Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>