DEWERT OKIN RF506A Remote Control User Manual
- June 4, 2024
- DEWERT OKIN
Table of Contents
RF506A Remote Control
User Manual
| Issue Department: Bedding Division| Date:| 2022-02-11
---|---|---|---
System Instruction| Author:|
|
User Manual| Edition:| 1.0
The page 1of 5
User Manual of RF506A
| Issue Department: Bedding Division| Date:| 2022-02-11
---|---|---|---
System Instruction| Author:|
|
User Manual| Edition:| 1.0
The page 2of 5
Figure 1 button remote
Item
-
1HEAD MASSAGE 1
Click the HEAD MASSAGE button, head massage motor switches massage intensity, massage intensity switches among 0-1-2-3； -
MASSAGE TIME SET 2
Click the message time button to set the massage time among 10min-20min-30min- off. -
FOOT MASSAGE 3
Click the FOOT MASSAGE button, foot massage motor switches massage intensity, massage intensity switches among 0-1-2-3 -
TV 4
Click the TV button, the bed moves to TV position, press and hold the TV button for 5s, until the backlight flashes, the control set the current position as TV position. -
MASSAGE 5
Press the Massage button to open and shut the head and foot massage.
| Issue Department: Bedding Division| Date:| 2022-02-11
---|---|---|---
System Instruction| Author:|
|
User Manual| Edition:| 1.0
The page 2of 5
6. M1 6
Click the M1 button, and the bed moves to the M1 position, press and hold the
M1 button for 5s until the backlight flashes, and the control set the current
position as the M1 position
-
HEAD UP 7
Press and hold the HEAD UP button, the head actuator moves out, stops when released. -
HEAD DOWN 8
Press and hold the HEAD DOWN button, the head actuator moves in, and stops when released. -
FLAT 9
Click the FLAT button, the bed goes flat. -
ZG 10
Click the ZG button, and the bed moves to zero position, press and hold the zero buttons for 5s, until the backlight flashes, and the control set the current position as zero position -
FOOT UP 11
Press and hold the FOOT UP button, foot actuator moves out, stop when released. -
FOOT DOWN 12
Press and hold the FOOT DOWN button, foot actuator moves in, stops when released. 3 / 5 Date： 2022-02-11 Author： Edition： Page 3 of 5 1.0
| Issue Department: Bedding Division| Date:| 2022-02-11
---|---|---|---
System Instruction| Author:|
|
User Manual| Edition:| 1.0
The page 2of 5
13. Pair Key 13
Press and Pair key (under the remote in the battery room)button for 3seeonds
when supplying the power to the control box. and the blue light tinkle.if pair
successfully. the blue light is on.
Federal Communications Commission (FCC) Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation of the device.
You are cautioned that changes or modifications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
| Issue Department: Bedding Division| Date:| 2022-02-11
---|---|---|---
System Instruction| Author:|
|
User Manual| Edition:| 1.0
The page 2of 5
Canada, Industry Canada (IC) Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of
the device.