DEWERT OKIN RF53 Remote Control Instructions
- June 6, 2024
- DEWERT OKIN
Table of Contents
DEWERT OKIN RF53 Remote Control Instructions
Instruction
Item
1.1 Light button 1
Press the light button to turn on the light in the remote.
1.2 Lock button 2
Long press the Lock button for 3 seconds to unlock/lock the remote.
1.3 Pair button 3
Long press the pair button to pair the signal between the remote and control
box.
1.4 Head pillow up button 4
Press the head pillow up button to move out the head pillow actuator.
1.5 Head pillow down button 5
Press the head pillow down button to move in the head pillow actuator.
1.6 Waist up button 6
Press the waist up button to move out the waist actuator.
1.7 Waist down button 7
Press the waist down button to move in the waist actuator.
1.8 Fifth up button 8
Press the fifth up button to move out the fifth actuator.
1.9 Fifth down button 9
Press the fifth down button to move in the fifth actuator.
1.10 Head up button 10
Press the head up button to move out the head actuator.
1.11Head up button 11
Press the head down button to move in the head actuator.
1.12 Foot up button 12
Press the foot up button to move out the foot actuator.
1.13 Foot up button 13
Press the foot down button to move in the foot actuator.
1.14 Memory 1 position button 14
Click the Memory 1 position button to make the head actuator move the memory 1
position;and long press the memory 1 position button until the remote
background light flash to set the memory 1 position.
1.15 Memory 2 position button 15
Click the Memory 2 position button to make the head actuator move the memory 2
position;and long press the memory 2 position button until the remote
background light flash to set the memory 2 position.
1.16 ZG button 16
Click the ZG button, the actuators move to ZG position.
1.17 AntiSnore button 17
Click AntiSnore button, the actuators move to AntiSnore position.
1.18 Massage head 18
Click massage head button, head massage motor switches massage intensity,
massage intensityswitches among 0-1-2-3；
1.19 Massage timer 19
If the massage motors work, click the button to switch the massage time, when
massage time switch to 0, turn off the massage;
1.20 Massage foot 20
Click massage foot button, foot massage motor switches massage intensity,
massage intensityswitches among 0-1-2-3；
1.21 Massage switch 21
Click massage swtich button to turn on/off the massage.
1.22 Light under the bed 22
Click the button turn on/off the light under the bed；
1.23 Massge mode 23
Click masage button swtich the massage mode;
1.24 Flat 24
Click FLAT button, the bed goes flat, stop when click any button during the
process of going flat；
1.24 A/B bed control select 24
Set the A/B bed control select button to contrl the A bed or B bed or AB
together;
FCC:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IC RSS warning
This device complies with Industry Canada licence-exempt RSS standard (s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,including interference that may cause undesired operation of the device.
ISED RSS Warning:
This device complies with Innovation,Science and Economic Development Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection againstharmful interference in a
residential installation. This equipment generates, uses and can radiateradio
frequency energy and, if not installed and used in accordance with the
instructions, maycause harmful interference to radio communications. However,
there is no guarantee thatinterference will not occur in a particular
installation. If this equipment does cause harmfulinterference to radio or
television reception, which can be determined by turning the equipmentoff and
on, the user is encouraged to try to correct the interference by one or more
of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>