DEWERT OKIN RF52 Remote Control User Manual

RF52 Remote Control
User Manual

RF52 Remote Control

1. PAIR（HEAD UP+ Head Down ） （button 10 in figure 1）
   Press and hold the HEAD UP+ HEAD DOWN button of the remote, and remote into pair mode；

2. HEAD UP （button 10 in figure 1 ）
   Press and hold the HEAD UP button of the remote, the head actuator moves out, and stops when released ；

3. Head Down （button 13 in figure 1 ）
   Press and hold the HEAD DOWN button of the remote, the head actuator moves in, and stops when released ；

4. FOOT UP （button 11 in figure 1 ）
   Long press the corresponding button, the foot driver extends, release the driver stops running

5. FOOT DOWN （button 14 in figure 1 ）
   Long press the foot down button, and the foot driver retracts, releasing the driver to stop running

6. TILT UP （button 12 in figure 1 ）
   Long press the corresponding button, the headrest driver extends, release the driver stops running

7. TILT DOWN （button 15 in figure 1 ）
   Long press the corresponding button, the headrest driver retracts, release the driver stops running

8. FLAT test （button 7 in figure 1 ）
   Click the FLAT button and release it, and the head and foot drivers run to the lowest position (when the driver is idle, the vibration motor can be turned off with one button,  and the indicator light of the vibration motor can be turned off), and the action will stop when any button is pressed;

9. ZG position test （button 9 in figure 1 ）
   After pressing and releasing, the head and foot drive run to the ZG position ()
   Press and hold the ZG button for 5s until the backlight indicator of the remote control flashes, and the control box sets the current position as the ZG position;

10. TV Position Test （button 5 in figure 1 ）
    Press and release, and the head and foot drives run to the TV position ()
    Press and hold the music button for 5s until the backlight indicator of the remote control flashes, and the control box will set the current position as the TV position;

11. LOUNGE Position Test （button 5 in figure 1 ）
    Press and release, and the head and foot drives run to the lounge position ()
    Press and hold the music button for 5s until the backlight indicator of the remote control flashes, and the control box will set the current position as the lounge position;

12. M1 Position Test （button 4 in figure 1 ）
    Press and release, and the head and foot drives run to the m1 position ()
    Press and hold the music button for 5s until the backlight indicator of the remote control flashes, and the control box will set the current position as the m1position;

13. M2 position test （button 6 in figure 1 ）
    Press and release, and the head and foot drives run to the M2 position ()
    Press and hold the M2 button for 5s until the remote control backlight indicator flashes, and the control box will set the current position as the M2 position;

14. Anti-snoring position test （button 1 in figure 1 ）
    Press and release, and the head and foot actuators run to the anti-snoring position ()
    Press and hold the anti-snoring button for 5s until the backlight indicator of the remote control flashes, and the control box will set the current position to the anti-snoring position;

15. Incremental test of head massage motor （button 16 in figure 1 ）
    Each time you click HEAD+, the massage will increase in turn, with a total of 3 levels of massage intensity.
    The default 10 minutes 0-1-2-3-0 intensity cycle,

16. Foot massage motor incremental test （button 18 in figure 1 ）
    Each time you click FOOT+, the massage will increase in turn, with a total of 3 levels of massage intensity.
    The default 0-1-2-3-0 intensity cycle is 10 minutes,

17. Head massage motor friction decrease test （button 19 in figure 1 ）
    Each time the “HEAD – button is clicked, the vibration intensity of the massage motor decreases by one level, and the massage intensity is 3 levels in total. 0-3-2-1-0 intensity cycle

18. Foot massage motor friction reduction test （button 21 in figure 1 ）
    Each time you click the FOOT – button, the vibration intensity of the massage motor decreases by one level, and the massage intensity has a total of 3 levels. 0-3-2-1-0 intensity cycle

19. Massage Time test （button 17 in figure 1 ）
    Click the Massage Time button, and the massage time switches to 10-20-30-0 min cycle, when no message is turned on, the button is invalid

20. MassageMode test （button 20 in figure 1 ）
    Click the massage mode button to switch between 3 massage modes for the feet. When no message is turned on, the button is invalid.

21. Under-bed lamp test （button 8 in figure 1 ）
    Click the UBB button to turn on the under-bed light, then click to turn off

22. Key lock test （button 2 in figure 1 ）
    Press and hold the lock button for 3 seconds until the backlight flashes, and the remote control enters the locked state; in the locked state, press and hold the lock button for 3 seconds until the backlight flashes, and the remote control lock state is eliminated;

Federal Communications Commission (FCC) Statement

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received, including interference that may cause undesired operation of the device.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning for Portable devices:
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Canada, Industry Canada (IC) Statement

This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

ISED RF exposure statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The device has been evaluated to meet the general RF exposure requirements.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>