BLITZWOLF BW-ST01 Smart Toilet Seat 1400W UV Nozzle Smart Detection Multiple Cleaning Toilet User Manual

BLITZWOLF BW-ST01 Smart Toilet Seat 1400W UV Nozzle Smart Detection

Multiple Cleaning Toilet

PARTS NAMES

Spare parts

1. Installing spare parts
2. Water inlet spare parts
3. User manual

CAUTION:

• Be sure to use the mounting plate delivered with this package.
• Do not use the product if the main unit is unstable.
• Doing so may cause the main unit to come loose and fall, resulting in injury

How to mount the plate

1. Install the expansion rubber plug into the ceramic mounting hole.
2. Place the mounting plate above the mounting hole of the ceramic.
3. Mounting bolts and nuts into the bolt guides and adjust the slide.
4. Use mounting bolts and nuts to lock the adjustable slide and the bolt guides to mount the plate.

How to install the main unit

1. Align the bottom of the main unit to the direction of the mounting plate.

2. Push in the direction of the arrow.
   When you hear a click, it means installation is complete.

3. Pull it slightly towards you to make sure the product will not loosen after installation.

TIPS

Tips for mount the plate installation:
First, install the mounting plate IN A LOOSE WAY, install the main unit, adjust the position, then press the push rod to remove the unit, lock the mounting plate firmly. Then you are done.

Power and water supply

• Installation diagram
  Waterproof 10A socket with ground fault circuit breaker
  The installation location of water and electricity should be set separately
  The water supply sOurce is transrerred through the |-valve, one end 1s Connected to the ceramic water tank to enter the water,the other end is connected to the water supply hose, and finally the water supply hose outlet is connected to the adapter of the unit.

• Water supply
  WARNING

1. Applicable water pressure range is 0.075Mpa-0.75Mpa
2. Applicable water temperature range is 5-35’C
3. Water supply hose length 0.6m; Valve should be close to the installationand disassembly position of this product.
4. Use the new hose set included with thiS equipment.  

Do not reuse an old hose set.

• Power supply

  1. nstall the 120V (greater than 15A) socket at a position above 60cm from the ground.
  2. The socket should be installed in a place where water is not easy to splash.
  3. Use a grounded socket.
  4. nsert the leakage protection plug of the product into the socket.
     WARNING
     Please connect the power according to the power supply requirements of the product, otherwise, it may cause product failure; the plug should be connected to an effectively grounded socket, Otherwise, in the case of power ailure or leakage, it may cause electric shock.

• Turn on the valve
  Before turning on the power, valve must be tumed on for water supply to the unit. CAUTION
  When power is turned on, the unit self-check system will be activated.
  You will hear an alarm under water supply failure. The following steps should be taken then:
  Turn off the power– turn on the valve—power on again.

Confirmation and trial operation

1. Check power
   Confirm that the leakage protection plug is plugged in tightly. The LED lits up that the system has been powered on. If the LED is not on, you can press the Reset button on the plug to power on. After power on, you can hear an eep sound from the system.

2. Occupied sensor
   The area shown in the figure is the Occupied sensor.Only when the system senses that the human body is in the siting state, the system function start.

3. Check rear wash
   Press the rear wash button on the armrest to activate the rear wash function (need to maintain the seated state)

4. Check front wash
   Press the front wash button on the armrest to activate the front wash function (need to maintain the seated state)

Function Explanation

REAR WASH
When the seat senses that the human bocy is seated, press the rear wash button in the stop or other mode, the buzzer sounds, the rear wash function is turned on, and it ends Butomatically after 3 minutes.
During the cleaning process, press this key again to open or cose the move ceaning function f the human body leaves the seat after the function is activated, exit the function.

FRONT WASH
When the seat serses that the human body is seated, press the front wash button in the stop or other mode, the buzzer SOunds, the feminine cleaning function is turned on, and it ends automatically atter 3 minutes. During the cleaning process, press this key again to open or close the move cleaning function. r the human body leaves the seat after the function is activated, exit the function

WATER TEMP
Press this key to adjust the water temperature. The water temperature is adjustable in 4 levels. When the LED Is off, the water temperature is tne tap water temperature. According to the uSe environment, U8 BCual water enmperature 1s about 30U-41C

• Water temperature level 1 About 33
• water temperature level ABOUT 35C
• Water temperature level is about 37C
• water temperature AbOut level 4

SEAT TEMP
Press this key to adjust the seat temperature. Ihe seat temperature is adjustable in 4 eves. evening LED s oT, tne Seat temperature is tne room temperature. according to the USe environment, tne dual seat temperature is about  0C42C. when the human body is seated, the anti-ow temperature scald function is automatically turned on ifter 15 minutes, and the seat temperature is reduced to level 1.

COLD & HOT SPA 
During the cleaning process, press this button to start Cold& Hot SPA press it again to stop Cold& Hot SPA, and at the same time the temperature returns to the normal cleaning state. 5 seconds cold water and 15 seconds set hot water alternate.

CHILDREN
Long press this button for 3 seconds to activate children mode. when children more iS on, short press this button winner seated or not to start children ceanin9 g TOr minute; level i ot water pressure, Evel 4 of nozze position and level 2 of water temperature.  hen children mode off, short press this button to activate children cleaning when seated.

NIGHT LIGHT
Short presS this key to tum on/oft night light.
Press and hold this button for 3 seconds to tum on/off the smart night light mode. Ihe factory default mart night light mode: night light turns on/off according to the ambient light automatically.

STOP
When cleaning. Press this key to stop the cleaning function.
or press is Duron, water pressure, no22e position, water, and seat temperature are same wi the previous setting. Long press to activate standby mode when power on.

NOZZLE POSITION FORWARD
Press this key to moe the nozze position forward in rear wash, front wash, and children. here are 4 levels in total. Each press, the nozzle moves toward 1 level

NOZZLE POSITION BACK
Press this key to move the nozzle position back in rear wash, front wash, and children. nere are 4 eves in total. Earn press, tne Nozze moves forward i level

INCREASED WATER PRESSURE
Press this key to increase spray pressure in rear wash, front wash, and children here are 4 levels in total. Each press increases the cleaning intensity by 1 level

REDUCED WATER PRESSURE
Press this key to reduce spray pressure in rear wash, front wash, and chicken nere are 4 1evels in total. Each press reduces tne cleaning intensity Dy Evel.

Function Description

Seating detection
There is a seat detection switch on the seat ring, which is used to detect whether there is a person seated. After the human body is seated, it can run the rear wash and front wash functions; when the rear wash and front wash unctions are turned on, the human body leaves the seat, and the above functions are automatically turned off.

Manual cleaning
When the occupied sensor is not activated, long-press the nozzle forward key.
The nozzle extends out for manual cleaning with a toothbrush. When finished, press “Stop” button to withdraw the nozzle.
The nozzle will also retract automatically after 3 minutes of cleaning.

Nozzle self-cleaning
Nozzle will be washed automatically before and after each use.

Portable disassembly
The main unit can be disassembled for easy cleaning and maintenance

WARNING
Unplug the unit before cleaning the surface.This product is an electric appliance. Be carefu not to let water and ceaner seep inside or Leakage protection plug. Doing so may result in fire, electrical shock or short circuit.

Cleaning the main unit

How to manually clean the nozzle
long-press the nozzle forward key. Nozzle will extend out for manual cleaning. Clean gently with a toothbrush or wet cloth. Press the “Stop” button to return the nozzle.

Do not press or pull the nozzle hard, Doing so may cause damage or malfunction.

How to clean the filter element
When water flow becomes small during use, please try to clean the flter element. Disconnect water inlet hose and the unit before the take-off adapter and clean the filter.
WARNING: Turn off T-valve and unplug the unit before cleaning. Make sure the power off and the water supply shut off.

Main unit surface cleaning (daily)

1. Cut off the power
   Always turn off the power before cleaning the unit.

2. Periodically, wipe off the seat unit with a soft cloth dampened with water.
   Dirt that is difñcult to clean can be wiped with dliluted neutral detergent.
   Do not wipe this product with toilet cleaner household cleaner, benzene, paint thinner, powdered cleanser or nylon scrubbing brush.
   TIPS: If the urine attached to the main unit is not wiped off in time, the main unit may be dyed pink or brown.

• Close the valve, Loosen and disconnect the water supply hose, to drain water in the following situations.
  • When the water may freeze in some winter area
  • Long Periods of Disuse
• Poor water quality may caUse dermatitis and product damage.

Drain the water and cut off power

1. Cut off power, and unplug the plug.

2. Close the T-valve to stop the water supply to the system.
   Remove the water supply hose from the valve and drain the water out ot the water supply hose.
   (If necessary)

3. Press and hold the putter in the direction of (arrow 1). then go in the direction of the operation itself (arrow 2) Remove unit horizontally

Winter product maintenance
When the ambient temperature is likely to drop to 32’F (0C) or lower, prevent damage to the pipes and hoses due to freezing. Please take measures to prevent freezing

• increase indoor temperature
• Close the valve
• Drain the water out of the water supply hose
  When using the product again, please confirm and test run (page 14).

Troubleshooting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>