ATN IR940 Long Range Infra Red Illuminator User Guide

June 1, 2024
ATN

ATN IR940 Long Range Infra-Red Illuminator

ATN-IR940-Long-Range-Infra-Red-Illuminator-product

INTRODUCTION

The IR940 IR Illuminator ensures that you stay hidden from your prey. Animals and humans alike are not able to see the wavelength at which the illuminator is emitting.

ATN-IR940-Long-Range-Infra-Red-Illuminator-fig-1

SPECIFICATIONS

ATN reserves the right to change the above specifications at any time without notice.

ATN-IR940-Long-Range-Infra-Red-Illuminator-fig-2

FEATURES

  • HIGH POWER LED EMITTER.
  • THREE MODES OF OPERATION.
  • SINGLE LITHIUM 18650 BATTERY WITH CHARGER.
  • REMOVABLE GRIP RING.
  • EASY RAIL MOUNTING SYSTEM.
  • BATTERY CHARGER.
  • ONE-YEAR WARRANTY.

BATTERY

ATN-IR940-Long-Range-Infra-Red-Illuminator-fig-3

NOTE
Please hold the battery tube (not the brightness control ring or neck) when tightening/losing the tail cap.

CAUTION
Only use an 18650 battery to operate this light, do not use 2 CR123 batteries as they may damage the device.

The IR940 IR Illuminator uses one 18650 battery.

  1. Remove the tail cap unscrewing it until it is free of the body.
  2. Install the battery in the body, observing proper battery polarity.
  3. Install the tail cap back on the body.

MODES
The IR940 has a three-stage output — Low, Medium and High system. Low at 50%. Medium at 75%. High at 100%.

BRIGHTNESS SET TINGS

The factory preset modes control the brightness of the IR illuminator. Three modes are designated on the head after the focusing ring. The modes are distinguishable by the size of the dot. The small dot indicates the lowest power output setting. The medium dot indicates the medium output power setting. The large dot indicates the strongest output power setting. To turn on/off the IR illuminator push the button on the tail cap. To switch the modes rotate the setting ring behind the focus ring of the IR illuminator.

FOCUS
Turn the light on to maximum output and shine it on a wall 8~10 m away. To focus the beam, hold the head in one hand and turn the neck section with your other hand turn clockwise or counterclockwise.

MOUNT
Attach the IR940 to the adjustable mount as follows:

ATN-IR940-Long-Range-Infra-Red-Illuminator-fig-4

  1. Unscrew the two screws.
  2. Place the insert in the mount.
  3. Insert the illuminator into the mount with the insert.
  4. Secure the two screws using an Allen wrench. Do not apply excessive torque.

ALIGNING THE IR BEAM
To Align the IR940 illuminator to your scope. After the IR940 is assembled into the mount. Place it on the X-Sight 5-side accessory rail or your Rifl es accessory Picatinny rail. Once mounted securely, slightly loosen the two screws on top of the mounting ring. While looking through the X-Sight 5 at night with night mode activated. Move the IR940 around in the mount until you see the IR light covering your entire field of view in the X-Sight 5 viewfinder. Once you have adjusted your IR light to be aligned with your X-Sight 5 FOV, gently tighten the two screws on top of the mounting ring with an Allen wrench.

MAINTENANCE

To prevent wear and retain water resistance it is a good idea to lubricate the threads and o-rings if they become dry.

TROUBLESHOOTING

Light Doesn’t Turn On
Check that the battery tube is fully threaded, as well as the tail cap.

Light Dimming

  • If the output is declining rapidly unexpectedly, please try another fully charged battery and/or charge your battery and retry.
  • If output is not fixed with other charged batteries, please contact ATN  for further assistance.

Important Export Restrictions! Commodities, products, technologies and services contained in this manual are subject to one or more of the export control laws and regulations of the US BIS-Department of Commerce, Export Administration Regulations. It is unlawful and strictly prohibited to export or attempt to export or otherwise transfer or sell any hardware or technical data or furnish any service to any foreign person, whether abroad or in the United States, for which a license or written approval of the U.S. Government is required, without first obtaining the required license or written approval from the Department of the U.S. Government having jurisdiction. Diversion contrary to U.S. law is prohibited.

For customer service and technical support, please contact
American Technologies Network Corp.
2400 NW 95 Ave, Doral, FL 33172
phone: 800-910-2862, 650-989-5100
e-mail: service@atncorp.com
www.atncorp.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals