FBO G-1555 Baby Hair Clippers Instruction Manual

FBO G-1555 Baby Hair Clippers

Thank you for choosing our products. The affirmation of our products will be our greatest honour and motivation. Before using our products, please read the product instructions in detail so that our products can bring you the joy of life. After-sales questions or SUG, please send us a message, and we’ll give you a reasonable and 100% satisfactory solution.

Product Specification

• Dimensions: 132. 7X56. 3X40. 33mm
• Weigh: approx. 119g
• BatteryType : 3.7V, Li-ion, 500mAh
• Input voltage: 5V/1A
• Charging time : 1 hour
• Operating time(on full charge): up to 90 minutes

Technical Characteristic

Safe Haircutting Clipper
Adopts ceramic blade to cut kids’ hair without pulling hair or scratching skin

Silent Buzzer
Our noiseless trimmer is lower than 55 dB and suits infants, toddlers, babies, boys and especially autistic kids &sensory sensitive children.

Cordless &USB Rechargeable
After shaving 40-60mins and the power indicator turns red, you need to recharge it through a USB cable for 1 hour.

PRODUCT OVERVIEW

• 3 X guide combs (3-6mm/9-12mm/2-12mm)
• 1 X Cleaning Brush
• 1 X blade oil
• 1 X USB connection
• 6 X Hairstyle models
• 1 X Hard Storage Case
• 1 X Carring Bag
• 1 X Hairdressing cape
• 1 X sponge
• 1 X Long Comb

BASIC INSTRUCTION TO USE

1. Insert the guide comb into the appliance to lock it in place.
2. The hair to be cut should be dry.
3. Push the on/off button to turn on the clipper.
4. Connect the USB charging cable to a power adapter. Red LED is lit.
5. Disconnect the USB charging cable when the charging indicator changes to white.

CHARGING

Multiple & Simple Ways to Charge
The hair clipper comes with a USB cable. You can charge the hair trimmer by plugging it into an AC adapter, power bank or any other USB enabled charger.

1. DUSB insert to the charging connector
2. Switch off the appliance. connect the usb to charger/powerbank/PC
3. Turn on the botton, In the event of a shortage of electricity during use, it also can be plug-in use.

GUIDE COMBS

Different sizes of guide combs can easily meet different needs of hair lengths.Make sure the groomer is in OFF state before changing the combs. There are two comb attachments of 3-6mm / 9-12mm / 2-12mm for different lengths of cutting.

ATTACHING GUIDE COMB

1. Guide combs should be installed by first hooking the blade teeth to the front side of the guide comb. Then press the back of the guide comb down until it snaps into place.
2. Ensure comb is attached before beginning to cut hair.
3. To remove, pull the snap tab on the backside of the guide comb and pull the comb off.
4. CD Install the comb
5. Remove the comb

BLADE INTALL AND HEMO\IE

Blade characteristic

Blade: Ceramic Blade The special 28 teeth cutting is more fine, more suitable for a baby’s soft hair.

Remove

Make sure the groomer is OFF state before removing the blade. Hold the handle of the groo­mer firmly and push the part of the blade away.

Install the blade

1. Make sure the groomer is OFF state before removing the blade. Connect the blade A and put it into B of the body groomer.
2. Push down on the guard, until you hear a SNAP”

CUTTING IIAIH

WITH COMB ATTACHMENT

Before starting, comb the hair in the direction of your hair. Pressing the comb against the head, start by clipping the sides from the bottom of the head upwards. Slowly move the clipper up towards the top of the head cutting small amounts at time. Clip the top of the head from front to back.

Note
Always start with a longer length guard.(you can always use a shorter length guard if the length is not short enough) The first time you cut hair, cut only a small amount of hair until you become accustomed to the length of hair each attachment guard provides.

WITHOUT COMB

No attachments needed. Start with the sideburns. Continue around the ear. Trim neckline.

MAINTENANCE

NOTE

1. Keep any packaging materials away from children and pets. These materials are a potential of danger.
2. Check the appliance for transport damages.
3. Clean the appliance and all the accessories before first use.

CLEANING

After every use

1. Turn off the product and disconnect from the power outlet.
2. Remove any guard or cutting element from the product.
3. Clean the blades and comb attachments with the cleaning brush to remove remaining loose hair clippings
4. Rinse the hair clipper under a warm tap.
5. Let all parts with dry cloth.

LUBRICATION

The cutting blades should be tightly oiled once every few haircuts as show.

USE AND MAINTENANCE

1. Check the blade for damage or foreign objects before use Do not use the appliance if it is not in proper condition to avoid skin irritation or appliance damage.
2. Avoid pressing the blades strongly against the skin, being especially careful around the ears. (The blades should be directed toward the skin at a right angle, but without significant pressure).
3. To clean the unit, use either a clean, dry or dampened cloth. DO NOT USE benzine or thinner to clean the unit.
4. Do not store the clipper in a wet or moist environment.
5. To prolong blade life, do not use a clipper on hair that is coated with a permanent wave solution or hair spray.
6. Do not touch any of the internal mechanisms, if the unit should need repair, do not repair it yourself.

CIIAHGING

Before using it, make sure it is completely charged. Connect the USB side of the charging cable to the regular adaptor (5V/1A) and plug-in the other side at the bottom of the trimmer While charging, the indicator will light up in red colour. The charging time is 1 hour and when fully charged, it can be used for about 90 mins.

CAUTION

1. Make sure the product is turned off.
2. Insert the small plug into the product and put the power plug in any 5V1 A-2A AC outlet .
3. After charging, remove the power plug from the wall outlet and pull the small plug out of the product.

Note:
An adapter plug may be necessary for cord usage in some foreign countries.U se an attachment plug adapter of the proper configuration for a power outlet.

TO REMOVE TIIE BATTEH PACK

Before disposing of this hair clipper, the internal rechargeable batteries must be removed for separate disposal.

NOTE: This process is not reversible.

1. Disconnect the hair clipper from the charger.
2. Switch on the hair clipper and allow it to operated until it stops and the battery is exhausted.
3. Switch off the hair clipper.
4. Removed the comb attachment and blade assembly.
5. Detach the blade holding base from the clipper and then open the housing.
6. Take out the circuit board and batteries.
7. Cut off the batteries from the circuit board.

CAUTION:
Once the batteries have been removed, take precautions to avoid any contact between the terminals. Dispose of the hair clipper and the batteries separately in accordance with your local recycling regulations.

NOTES FOR BATTERY DISPOSAL
The batteries used with this product contain chemicals that are harmful to the environment. To preserve our environment, dispose of used batteries according to your local laws or regulations. Do not dispose of batteries with normal household waste.

TROUBLESHOOTING

Clipper doesn’t start

1. Check to see if clipper is plugged in.
2. Replace power cord if frayed, cracked, or damaged
3. If clipper is plugged in and cord is in good condition, check the switch by turning on and off

Motor runs, but blade isn’t moving or sticks:

1. Clean blade set and oil
2. Replace blade set if blade teeth are broken
3. Adjust power screw to retune the clipper Clipper making loud noise:
4. Adjust power screw to retune the clipper

Clipper pulls hair:

1. Dirty or dry blades, clean blades and oil
2. Blades are dull – replace blades
3. Check blade alignment

Blade nicks or cuts:

1. Check blade alignment
2. Replace blade set if blade teeth are chipped or broken

HOW TO USE HAIRSTYLE MODELS

• Step 1: Cut your hair short to about 3 to 6mm.
• Step 2: You can use double-sided adhesive to stick it on the model and then stick it on your hair to fix it before carving (there are many methods that you can think of how to use it, or you can hold the model by hand to operate it). It depends on your own technology whether the carved figure looks good or not. Be careful, be patient and practice it slowly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>