SUNRICHER 70100005 Single Color Wall Mounted ZigBee Remote Controller Instruction Manual

70100005 Single Color Wall Mounted ZigBee Remote Controller
Instruction Manual

Important: Read All Instructions Prior to Installation

Function introduction

Note  This remote supports 4 groups for binding max. 30 lighting devices.

Product Data

• ZigBee dim remote based on ZigBee 3.0
• Enables to control of both single color lighting devices
• Battery-powered remote with low power consumption
• Enables to pair ZigBee lighting devices via touchline commissioning without coordinator
• Supports find and bind mode to pair with ZigBee lighting devices
• Supports 4 groups for binding max. 30 lighting devices
• 2.4 GHz global operation
• Transmission range up to 30m
• Compatible with universal ZigBee Gateway products
• Compatible with universal single color ZigBee lighting devices

ZigBee Clusters Supported by This Remote Are As Follows:
Input clusters:

Output clusters:

Safety & Warnings

• This device contains a button lithium battery that shall be stored and disposed of properly.
• DO NOT expose the device to moisture.

Quick Start (Simplified operation compared to standard operations in the part “Operation”)

Operation

1. This ZigBee Dim remote is a wireless transmitter that communicates with a variety of ZigBee compatible systems. This transmitter sends wireless radio signals that are used to remotely control a  compatible system.
2. This ZigBee remote supports 4 groups for binding max. 30 lighting devices and enables to control single color ZigBee lighting devices.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

Note:

1. After pairing successfully, the remote information will appear on the controller or hub interface.
2. No remote information will appear on the hub interface if paired to Philips Hue Bridge.

TouchLink to a Zigbee Lighting Device

Note:

1. Directly TouchLink (both not added to a ZigBee network), please the first factory reset both the remote and device, each remote can link with max. 30 devices, please make sure the first linked device is always powered on when touching the remote with 2nd device and more devices.
2. TouchLink after both are added to a ZigBee network, each device can link with max. 30 remotes.
3. To control by both remote and hub, add both remote and device to network first then TouchLink, after TouchLink, the device can be controlled by the linked remotes and Zigbee hub together.

Removed from a Zigbee Network through Coordinator or Hub Interface

Factory Reset Manually

Remove a Touchlink Paired ZigBee Lighting Device

Factory Reset a Lighting Device (Touch Reset)
Note: the device shall be added to a network, the remote added to the same one or not added to any network.

**Find and Bind a Zigbee Lighting Device

**

Note: Make sure the device and remote are already added to the same Zigbee network.

Find and Unbind a Zigbee Lighting Device

Clear All Find and Bind Mode Paired Lighting Devices

Setup a Network & Add Devices to the Network (No Coordinator or Hub Required)

Step 6: Add more remotes to the network as you would like.
Step 7: Factory reset the lighting devices that you would like then add them to the network, refer to their manuals.
Step 8: Touch the link to pair the added remotes and lighting devices, refer to their manuals. Each remote can link with max. 30 lighting devices. Each lighting device can be linked by max. 30 remotes.

OTA
The remote supports firmware updating through OTA and will acquire new firmware from the Zigbee controller or hub every 10 minutes automatically.

How to Check Whether the Remote Belongs to a Network or not
Short press any button, indicator blinking means the remote has already been added to a network, no blinking of the indicator means the remote does not belong to any network.

Battery Power Monitor Function

The remote will report battery power value to the coordinator under the following situations:

• When powered on.
• When short press both buttons of group 2 simultaneously.
• When operating the switch to send data packets (over 4 hours since the last operation).
• When added to the network by a coordinator.

Installation

1. Remove battery insulator
   

2. Install the controller to wall(2 methods)
   

Mounting

The key part of this controller is a universal one, especially the rotary standard switch element that can be integrated in numerous frames by different manufacturers as below list:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>