Armacost LIGHTING 723422 Slimline RGB Plus W Color LED Controller Instruction Manual
- June 17, 2024
- Armacost LIGHTING
Table of Contents
Armacost LIGHTING 723422 Slimline RGB Plus W Color LED Controller
Specifications
- Product : Slimline RGB+W Color LED Controller
- Model : 723422
- Features :
- RF Remote Control
- Wireless Remote
- Ultra Compact
- Wide Voltage Range
- Memory Function
- Overheat Protection
Product Usage Instructions
-
Receiver & Wiring
Make sure the voltage of the LED lighting matches the power supply and the maximum load doesn’t exceed that of the controller.
CAUTION: Avoid shorting output cables to prevent permanent damage. Ensure cables are well insulated. -
Wiring Diagram
Connect the power supply to the controller input and the controller output to the LED lighting. Ensure all power cables are securely connected and insulated before powering on. -
On/Off
Press the | key to turn on the controller or the 0 key to turn it off. The controller will remember its state when powered off and return to that state when powered back on.
FAQ
-
What should I do if the remote control is not working?
If the remote control is not functioning properly, try replacing the CR2032 battery. Ensure there are no obstructions between the remote and the receiver. -
Can I pair multiple remotes with one controller?
Yes, up to 5 remotes can be paired with one receiver. Follow the pairing instructions provided in the manual to pair additional remotes.
Slimline RGB+W Color LED Controller With RF Remote Control
Model # 723422
Introduction
This LED controller is designed to drive constant voltage RGB+White LED
products such as LED tape light or LED fixtures in a voltage range of 5–24
volts DC. The receiver works with the RF wireless remote control, which allows
the user to choose between multiple colors, adjust the LED brightness, and
select dynamic effects.
Receiver & wiring
-
Input – from power supply
The controller input and output voltage range is 5–24 volts DC. Make sure the LED lighting voltage is within this range and below the rated wattage of the power supply. Connect input wires from the power supply to the controller as indicated by the polarity markings on the controller (+ to + and – to –). -
Output – to LED lighting
Observe polarity indicated on the controller when connecting to LED lighting (+ to +, G to G, R to R, B to B, and W to W). Make sure the voltage of the LED lighting is the same as the power supply and the maximum load doesn’t exceed that of the controller.
CAUTION: Shorting of output cables could cause permanent damage to controller. Make sure cables are well insulated from each other. -
Wiring diagram
Connect the power supply to the controller input and the controller output to the LED lighting. The output voltage of the power supply must be the same as the voltage of the LED lighting. Make sure all power cables are connected securely and insulated before powering on.
Remote Control -
On / Off
Press the “|” key to turn on controller or the “0” key to turn off. The controller will remember the controller state when powered off, and will return to that state when powered back on. -
Mode selection
Press this key to switch between RGB, white, and RGB + white mode. If the RGB mode is selected, the white channel will be disabled, and if the white mode is selected, RGB channel will be disabled. In RGB + White mode all channels are enabled. -
Select static RGB color
Press the “COLOR+” and “COLOR–” keys to scroll through the preset library of colors. -
Shortcut color keys
Press to select preset colors. -
White brightness control
Press to increase white LED brightness and press to decrease it. -
RGB brightness control
Press to increase RGB LED brightness and press to decrease it. -
Dynamic effect
-
Remote indicator
When pressing keys, the indicator blinks if the remote is working properly. If the indicator flashes slowly when pressing keys, battery power is low and it needs to be replaced. Replace with a CR2032 battery.
Remote control operation
- Using the remote control
Pull out plastic battery insulation tab before use. The RF wireless remote will work through walls and doors. Do not install in a metal enclosure.
-
Pairing with a new remote control
The remote control and receiver are already paired, but up to 5 remotes can be paired to one receiver.
To pair a new remote: -
Disconnect power to receiver and wait five seconds.
-
Reconnect power.
-
Within ten seconds, press the keys simultaneously for about three seconds until the remote indicator flashes quickly.
-
De-pairing remotes
To de-pair a remote control, pair the remote you wish to continue using with the controller and any other paired remotes will be de-paired.
Overheat protection
If the controller overheats, it will automatically shut down until the temperature drops to a safe range. If this occurs, check to make sure the output current is below the rated level.
Specifications
- Output mode …………………………………………… PWM constant voltage
- Working voltage ………………………………………………………. 5–24V DC
- Rated output current ………………………………………….. 4x2A (8A max)
- Static colors ……………………………………………………………………..30
- White brightness levels ………………………………………………………..10
- Color brightness levels ………………………………………………………….5
- Dynamic effects…………………………………………………………………42
- Dynamic speed levels ………………………………………………………….10
- Color preset keys …………………………………………………………………7
- PWM frequency ……………………………………………………………..1KHz
- PWM physical grade ……………………………………………….. 4000 steps
- Overheat protection …………………………………………………………… Yes
- Remote frequency …………………………………………………. 433.92MHz
- Remote control range …………………….. up to 50 ft./15m in open areas
- Controller dimensions ………………………………1.97 X 0.59 X 0.28 in./ …………………………………………………………………….50 X 15 X 7mm
- Remote dimensions ……………………………….3.41 X 1.42 X 0.329 in./ ……………………………………………………………….86.5 X 36 X 7.5mm
Customer support
- Email: support@armacostlighting.com
- Phone: 410-354-6000
- Monday–Friday, 9 a.m.–5 p.m., ET
Warranty
1-year limited warranty. This product is for dry location use only. Improper installation, improper powering, abuse, or failure to use this device for its intended purpose will void warranty. Proof of purchase is required for all returns. Questions? Email support@armacostlighting.com.
armacostlighting.com © 2023 Armacost Lighting. All rights reserved.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>