TRENDnet TEW-925DAP AX5400 Dual Band WiFi 6 PoE Plus Access Point Installation Guide
- June 10, 2024
- TRENDnet
Table of Contents
TRENDnet TEW-925DAP AX5400 Dual Band WiFi 6 PoE Plus Access Point
Before You Start
Package Contents
- TEW-823DAP / TEW-923DAP / TEW-925DAP
- Quick Installation Guide
- Network cable (0.5 m / 1.64 ft.)
- Mounting plates
Minimum Requirements
- A computer with an available network LAN port and web browser
- A PoE or PoE+ (dependent on AP model) Network with an available network LAN port connected to an existing network
Optional Equipment
- Power drill and Phillips bit or Phillips screwdriver for mounting
The table below displays the access point models and compatible PoE standard required for providing both power and data to the access point’s PoE or PoE+ LAN port.
Quick Reference
Note : The access point image and model number shown in diagrams and examples may be different from your access point.
By default, the wireless network name/SSID and wireless encryption settings
have been pre-configured for your convenience and can be located on the
included preset wireless sticker or on the device label located on the back of
the access point. By default, the access point web management configuration
page can be accessed using the URL http://
Hardware Installation and Configuration
Note : It is strongly recommended to configure the access point first before mounting.
-
Connect a network cable from a PoE or PoE+ switch to your access point and to your computer.
-
The LED will turn on to indicate that the access point is ready.
-
Assign a static IP address to your computer’s network adapter in the subnet of 192.168.10.x (e.g. 192.168.10.25) and subnet mask of 255.255.255.0.
-
Open your web browser, type the default URL http://
(ex: http://tew-823dap, http://tew-923dap, http://tew-925dap) or default IP address http:/1192.168.10.100 of the wireless access point in the address bar, and then press Enter. The default IP address is 192.168.10.100. 
-
Select your language from the Language drop-down list and enter the User name and Password, and then click Login. By default:
-
User Name: admin
-
Password: admin
-
To change the administrator password used to access the wireless access point configuration page, click on Management and click on Administration. Under the Administration Table, at the right, click Modify for the admin user entry. Enter the new password in the Password and Confirm Password fields and clickApplyto temporarily save the configuration changes.
Important Note : Configuration changes in the access point web management configuration page are not applied until you permanently
Save & Apply the configuration settings by clicking the disk icon at the top right or left navigation menu.
-
To configure your wireless network name/SSID and wireless encryption settings, click the wireless band you would like to configure Wireless 2.4GHz or Wireless 5GHz and click on Wireless Network.
-
In the Current Profiles, click Edit next to the enabled entry. You can enter a new wireless network name/SSID, select the Security Mode, and enter a new wireless encryption Password in the fields provided. Click Apply to temporarily save the configuration changes.
Note : The wireless network name/SSID is the name your WiFi clients will need to search and discover when connecting to your access point wireless network.
-
To configure your access point LAN IP address settings, click System and click IP Settings.
-
Under LAN Connection type, click the Connection Type drop-down list to select either DHCP {default setting) or STATIC. Selecting DHCP will set your access point to obtain IP address settings automatically from a DHCP server on your network and selecting STATIC will allow you to manually assign your access point IP address settings to meet the IP requirements of your network. Enter the new IP address settings in the IP Address, Subnet Mask, Default Gateway, and Primary/Secondary DNS Server fields. Click Apply to temporarily save the configuration changes.
-
After you have completed access point configuration, reconfigure your computer’s network adapter back to the original settings to obtain IP address settings automatically using DHCP, or enter the IP settings.
-
To ceiling mount the access point, first route the non-terminated network cable through the largest opening in the mounting plate and install the mounting plate to the desired ceiling using the included drywall anchors and screws. Install the mounting plate with the clip facing away from the ceiling. After the mounting plate is properly installed, connect the terminated network cable to the network PoE or PoE+ LAN port of the access point, align the access point mounting clips with the mounting plate clip and slide the access point to lock into place.
Celling mounting
To download the latest version of the user’s guide, please go to https://www.trendnet.com/support and select the access point model number and hardware version from the Product Download drop-down list.
Declaration of Conformity
Manufacturer’s Name and Address
TRENDnet, Inc. Zwolsestraat 156 2587 WB 20675 Manhattan Place The Hague The Netherlands Torrance, CA 90501 USA
Product Information
-
Model Number : TEW-823DAP / TEW-923DAP / TEW-925DAP
-
Product Name : AC1300 Dual Band PoE Indoor Wireless Access Point /
AX3000 Dual Band WiFi 6 PoE+ Access Point /
AX5400 Dual Band WiFi 6 PoE+ Access Point -
Trade Name : TRENDnet
TREND net hereby declare that the product is in compliance with the essential
requirements and other relevant provisions under our sole responsibility.
Safety EN IEC 62368-1: 2020 + All: 2020
EMC
- EN 55032: 2015 / AC: 2016
- EN 55035: 2017
- EN 301 489-1 V2.2.l (2017-03)
- EN 301 489-17 V3.2.0 (2017-03)
Radio & Health EN 300 328 V2.2.2 (2019-07) Spectrum EN 301 893 V2.1.1 (2017-05) IEC 62311: 2020 EN 50385: 2017 / EN 50665: 2017
Energy Efficiency Regulation (EC) No. 1275/2008, No. 801/2013
This product is herewith confirmed to comply with the Directives.
- Directives: EMC Directive 2014/30/EU
- RoHS Directive 2011/65/EU
- WEEE Directive 2012/19/EU
- REACH Regulation (EC) No. 1907 /2006
- Low Voltage Directive 2014/35/EU
- Radio Equipment Directive 2014/53/EU
- Ecodesign Directive 2009/125/EC
A person is responsible for this declaration. Place of Issue: Torrance, California, USA Date: April 21, 2023 Name: Sonny Su Title: Director of Technology
FCC
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interierence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the tile receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radionic technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment this device complies with Part 15 of the FCC Rules. Operation is subject to the allowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT NOTE: Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. this equipment should be installed and operated with
a minimum distance 20cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter.
Country Code selection leature to be disabled for products marketed to the
US/CANADA Operation of this device is restricted to indoor use only
Certifications
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received.
Including interference that may cause undesired operation.
Waste electrical an electronic products must not be disposed of with household A waste. Please recycle where facilities exist. Check with your Local Authority or Retailer for recycling advice
Technical Support
If you have any questions regarding the product installation, please contact
our Technical Support.
Toll free US/Canada:
1-855-373-4741
Regional phone numbers available at
www.trendnet.com/support
Warranty
Product Warranty Registration
Please take a moment to register your product online. Go to TRENDnet’s website
at:
www.trendnet.com/register
TRENDnet 20675 Manhattan Place Torrance, CA 90501 USA
Applies to PDE Products Only: This product is to be connected only to PoE networks without routing to the outside plant.
Note
The Manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void
the user’s authority to operate the equipment.
Note
The equipment power supply cord shall be connected to a socket outlet with
earthing connection.
Copyright© 2023. All Rights Reserved. TRENDnet. TEW-823DAP/fEW-923DAP/fEW- 925DAP / 04.21.2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>