Maxxima MEW-DM680 120V 3 Way or Single Pole Digital Dimmer Switch Instructions

Maxxima MEW-DM680 120V 3 Way or Single Pole Digital Dimmer Switch

Feature

Email: Info@maoimastyle.com

Contact: 86-MAXIMA(629-9462)

Website: www.maximastye.com

Address: 125 Cabot Cout Haupauge, NY 11788

Warnings and Cautions

1. Risk of fire and electrical shock, the dimmer should be installed in accordance with appropriate electrical codes and regulations.
2. Turn the power off at the circuit breaker or fuse before installing.
3. Please read ALL instructions before attempting to install this device.
4. If you are unsure about any part of these instructions, consult a licensed electrician.
5. To reduce the risk of overhead and possible damage to other equipment, do not install to control a receptacle, a motor-operated appliance, or a transformer-supplied appliance.
6. Use with compatible dimmable LED, CFL bulbs, Incandescent or halogen bulbs only.
7. When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either LED, CFL, or incandescent. Using the same model of each bulb will enhance dimmer performance.

Functional Specifications

Status Indicator

• Indicator lights red: OFF status
• Indicator lights green: ON status
• Short press: Within 0.5s
• Long press: Over 0.5s
• Continuous short press: Each interval of the short press should be within 1s

Set Minimum/Maximum Brightness using side Buttons
To set the minimum brightness level, short press the low button to decrease the minimum brightness. To set the maximum brightness level, short press the high button to increase the maximum brightness levels.

Set Minimum/Maximum Brightness using Power Button

• Turn on: Short press once when in OFF.
• Turn off: Short press once when in ON.
• Short press the power button six times to set the light to minimum brightness when in ON status.
• Short press the power button eight times to set the light to maximum brightness when in ON status.
• Continuous short press nine times to clear the setting brightness when in ON status
• Continuous short press ten times and the status indicator flash three times to restore the factory default settings. When in the maximum brightness status.

Dimming Button (UP)

• Short press the dimming button once can increase a level of brightness when in ON status.
• Long press the dimming button can continue to increase the brightness until release or reach the maximum brightness.
• Continuous short press two times to turn quickly to the maximum brightness.

Dimming Button (Down)

• Short press the dimming button once can decrease a level of brightness when in ON status.
• Long press the dimming button can continuously decrease the brightness until release or reach the minimum brightness.
• Continuous short press two times to turn quickly to the minimum brightness.

Power Cut-off

• Tab Pushin the power cut-off tab to connect the power.
• Pull out the power cut-off tab to cut off the power.

Luminance Indicator

Tools Needed for the Install

• Screwdriver
• Pliers
• Wire Strippers

Installation

• WARNING: To avoid fire and electrical shock, TURN OFF POWER at the circuit breaker or fuse and test that power is off

• Remove the screws installed on the existing wall plate and switch. Pull the existing switch out. (The above step is not required for new installation.)
• Identify the wires coming from the breaker. Take a picture of the connections for reference. Remove the connections between the wire from the wall box and the device.

Note: If the wires in the wall box are different from the following layouts, please consult an electrician.

Single Pole Install

1. Line
2. Neutral
3. Ground
4. Load

Note: The brown wire should only be used for 3- way installation. In a single-pole application, the brown wire should be protected by a wire nut.

• Connect the green copper dimmer wire with the ground (bare/green) wire of the wall box, and tighten with a wire nut.
• Connect the black dimmer wire with the breaker wire (typically black) of the wall box, and tighten with a wire nut.
• Connect the red dimmer wire with the load wire (typically red or black) to the wall box with a wire nut.

3 Way Install

1. Line or Load
2. Neutral
3. Ground
4. Traveler 1
5. Traveler 2

Note: A dark-colored screw (typically black or brass) is typically the Hotline. This can make idientifying the traveler wires easier. Travelers are interchangeable.

3-way connection 1

3-way connection 2

• Connect the green dimmer wire with the green/bare copper wire of the wall box, and tighten with a wire nut.
• Connect the black dimmer wire with the breaker wire (typically black) to the wall box, and tighten with a wire nut.
• Connect the brown dimmer wire with the first traveler wire (typically black or red) of the wall box, and tighten it with a wire nut.
• Connect the red dimmer wire with the second traveler (typically black or red) of the wall box, and tighten with a wire nut.

Installing The Dimmer

Installing with the Screwless Wall Plate:

• Install the wall plate base on the dimmer and tighten with matched screws

• Put the wall plate and base together, and press gently to make sure it is installed firmly

Installing with a Wall Plate:

• Install the wall plate on the dimmer and tighten it with the matched screws.

Installation Is Complete. Turn on the Breaker

Single-Pole

Quickly turn to

the maximum brightness

| Short press the dimming button (UP) twice
Quickly turn to

the minimum brightness

| Short press the dimming button (DOWN) twice
Setting the maximum brightness| Short press the power button EIGHT times
Setting the minimum brightness| Short press the power button SIX times
Clear the minimum brightness| Short press the power button NINE times
Restore factory setting| Short press the power button TEN times

Troubleshooting

2 YEAR WARRANTY

Maxxima extends a 2-year limited warranty to the original purchaser that the product listed is free from defects in material and/or workmanship only. Maxxima will replace any warranted product with the original consumer/purchaser if the product fails because of defects due to workmanship and materials within the limited warranty period. A limited warranty is not transferable and applies to the original installation of the Maxxima product. This offer does not constitute in any way a product guarantee and Maxxima does not hereby assume any obligation whatsoever beyond sending a free replacement product.

References

• Factory Direct LED Recessed Lighting, Outdoor Wall Lights, Ceiling Fixtures and Electrical Products

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>