lionelo LO-SVEN-PLUS Sven Plus Travel Bed User Manual

lionelo LO-SVEN-PLUS Sven Plus Travel Bed

Dear Customer

In case of any questions or comments on the purchased product, please contact us: help@lionelo.com

Note: The assembly of the product must be performed by an adult. Failure to comply with this provision and the assembly instructions could result in serious injury or even death.

Producer:
BrandLine Group Sp. z o. o.

IMPORTANTRETAIN FOR FUTURE REFERENCE

READ CAREFULLY

WARNINGS

• Be aware of the risk of an open fire and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the cot.
• Do not use the cot if any part is broken, torn, or missing, and use only spare parts approved by the manufacturer.
• Do not leave anything in the cot or place the cot close to another product, which could provide a foothold or present a danger of suffocation or strangulation, e. g. strings, or blind/curtain cords.
• Do not use more than one mattress in the cot.
• The cot is ready for use only when the locking mechanisms are on. Before use, carefully check that these mechanisms are fully switched on.
• The lowest position of the cot is the safest and should always be used as soon as the child starts to sit up.
• The upper position of the cot is suitable for children weighing up to 9 kg. If your child starts to sit down himself, use only the lower position.
• If you leave the child unattended in the crib, always make sure that the side entrance is fastened with a zipper.
• Before replacing the base with the lowest one, it is necessary to remove the support rails.
• All mounting elements should always be tight, connections should be regularly checked and tightened if necessary.
• The cot can not be used by children who can get out of it themselves, it may cause a fall and serious injuries or even death.
• WARNING – Only use the mattress sold with this cot, do not add a second mattress on this one, suffocation hazards.
• The mattress is an integral part of the bed.

CHANGING PAD WARNING – Do not leave the child unattended.

• The baby cots should be blocked before using the changing table.
• The changing table is suitable for children up to 12 months of age and weighs up to 11 kg.
• Any additional or replacement parts can only be obtained from the manufacturer.
• Do not use the changing unit if any part is broken, torn, or missing.
• Be aware of the risk of open fires and other sources of strong heat, such as electric bar fires, gas fires, etc. in the near vicinity of the changing unit.
• All mounting elements should always be tightened, joints should be checked regularly and tightened if necessary.

Safe use of batteries

• Batteries should not be charged.
• Batteries should only be charged under adult supervision.
• Batteries must be removed from the toy before charging.
• Do not insert different types of batteries or new and used batteries.
• Insert batteries with the correct polarity.
• Exhausted batteries should be removed from the toy.
• The supply terminals are not to be short-circuited.
• To replace the batteries: use a screwdriver to open the door and access the battery compartment. Replace the batteries and make sure they are inserted correctly. Screw the door with a screwdriver.
• The toy cannot be connected to more power sources than recommended.

Assembly instruction

1. Take the travel baby bed out of the bag and loosen the adhesive straps. Place the bed on the floor and put the bag aside.
2. Separate the legs pulling them apart. Keep the central lock-up. Otherwise, handrails will not fit in the right place.
3. Pull the middle part of each top rail covered with material so that they fit into place. Start with the longer rails, and then the shorter ones.
4. Note: So that the sides of the cot/handrails are properly blocked, the central blockade of the floor must be raised upwards. The baby rails will not lock when the floor is unfolded.
5. Push the middle lock until the surface is completely flat (you will hear the click sound).
6. Place the mattress in the baby bed (see fig. 5, 6). Fasten the mattress using Velcro on the two short sides of the mattress (there are special openings in the floor for fastening).

Base installation

The base must be attached using the zipper. Once the base is attached, cover the zipper with a Velcro pad. Slide the reinforcement tubes into the sewn handles and connect them (they must be paired properly). Place the mattress onto the tube-reinforced base and fasten it with Velcro.

Canopy installation

Slide the plastic arches into the material guide of the canopy and connect them in the middle. Place the rear part of the canopy on the baby bed, then stretch the fabric and attach the canopy to the baby bed using plastic clamp holders. After the roof has been mounted, it should be pressed several times from the top to get rid of the pointed shape, which is picked up in the carton. The mosquito net may only be used with the canopy folded out. If you want to fold the canopy – detach the mosquito net.

Changing table assembly instruction
Slide the stiffening tubes into the cloth rewinders. Combine them with additional pipes with plastic fasteners. Fasten the material with all the naps, and pull it firmly on the resulting frame. Insert the plastic fastening elements on the longer sides of the cot, and insert additional fasteners on the shorter side of the bed. Fasten the organizer’s naps to dedicated places on the bed frame, stretching the organizer’s material at the changing table .

Organizer installation
Put the hooks on the organizer and mount them on the bed frame. Baby bed folding instruction

1. Remove all the bed accessories. Remove the mattress, canopy, organizer, and all the other accessories. Grasp the center handle located in the middle of the floor and pull it up (see fig. 12).
2. To unlock the upper rails, press the indicated buttons on each side of them. Pull it slightly up and then push it down. Unlock the shorter sides first, and then do the same with the longer ones.
3. While still pulling up the handle, lift the floor of the baby bed and fold the legs.
4. Wrap the folded bed with the mattress and fasten it with Velcro straps. Put the folded baby bed into the bag .If the installation is unsuccessful, repeat the whole process again until submission

Cleaning

Wipe the product with a damp cloth, then allow it to dry. Changing table – clean with warm water and mild soap. Do not dry clean and do not use caustic agents. Do not dry mechanically, do not iron.
The product has been tested and meets all the requirements of the:
EN 716-1:2017+AC:2019, EN 12221-1:2008+A1:2013

Interactive dog:
This product complies with the requirements of the Toy Safety Directive (2009/48 / EC), therefore the CE mark has been affixed and a declaration of compliance with European standards has been issued. The pictures in this manual are for illustrative purposes only. Therefore, they may differ from the actual product. The product complies with the requirements of EU directives. Pursuant to the Directive 2012/19/EU, this product is subject to selective collection. The product must not be disposed of along with domestic waste as it may pose a threat to the environment and human health. The wornout product must be handed over to the electrics and electronics recycling center

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>