Reebok i-Run 4.0 Treadmill User Manual
- June 5, 2024
- Reebok
Table of Contents
Reebok i-Run 4.0 Treadmill User Manual
PARTS
Safety Key
Lubricating the Treadmill
- Every 3-6 months
** See User Guide for more info
User Information
This product is suitable for user’s weight of 120kg.
WEEE logo this symbol on a product means that the product is covered by European Directive 2012/19/EU.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by RFE International is under license.
Hereby, RFE international declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU.
Product Registration and Support
Exploded Diagram
Parts List
No./Description/Qty
| C07| Top Side Rail 2| D01| Nut (M6)| 9| E03| Switch Button| 1
---|---|---|---|---|---|---|---|---
C08| Lateral Side Rail 2| D02| Nut (M8)| 16| E04| Power Socket| 1
A02 Console Bracket| 1| | C09| Back End Cover 1| D03| Bolt (M1240)| 1| E05|
Overload Protector| 1
A03 Left Handle Bar Bracket| 1| | C10| Back End Side Cover-L 1| D04| Bolt
(M855)| 2| E06| Magnet Ring| 1
A04 Right Handle Bar Bracket| 1| | C11| Back End Side Cover-R 1| D05| Bolt
(M840)| 2| E07| Magnet Core| 1
A05 Left Upright Tube| 1| | C12| Tube End Cover-L 1| D06| Bolt (M815)| 6|
E08| Power Wire| 1
A06 Right Upright Tube| 1| | C13| Tube End Cover-R 1| D07| Bolt (M655)| 3|
E09| AC Single Wire (Brown 200)| 1
A07 Frame Reinforcement Tube| 1| | C15| Console Top Cover 1| D08| Bolt
(M512)| 13| E10| AC Single Wire (Brown 350)| 2
A08 Support Frame| 1| | C16| Console Bottom Cover 1| D09| Bolt (M860)| 6|
E11| AC Single Wire (Blue 350)| 2
B01 Connection Board I| 1| | C17| IPAD Holder Top Cover 1| D10| Screw
(ST2.98)| 2| E12| Grounding Wire (Yellow & Green 350)| 1
B02 Connection Board II| 1| | C18| IPAD Holder Bottom Cover 1| D11| Bolt
(M610)| 4| E13| PCB Board| 1
B03 Folding Metal Plate| 1| | C19| IPAD Holder Insert Part 1| D12| Bolt
(M510)| 4| E14| Control Board| 1
B04 Cylinder Metal Plate| 1| | C20| Tube Decoration Ring 2| D13| Screw
(ST4.212)| 28| E15| Top Signal Wire| 1
B05 Front Roller| 1| | C21| Handle Bar Foam-L 1| D14| Screw (ST4.230)| 2|
E16| Bottom Signal Wire| 1
B06 Back Roller| 1| | C22| Handle Bar Foam-R 1| D15| Screw (ST4.225)| 4| E17|
Hand Pulse Top Cover| 1
B07 Handle Bar Fasten Plate| 2| | C23| Hand Pulse Holder 2| D16| Screw
(ST4.212)| 28| E18| Hand Pulse Bottom Cover| 2
B08 Hand Pulse Metal Plate| 4| | C24| Handle Bar Cover-L 1| D17| Screw
(ST2.98)| 9| E19| On-Off Sensor| 1
B09 Cylinder| 1| | C25| Handle Bar Cover-R 1| D18| Washer (6)| 5| E20| Console
Acrylic| 1
B10 Safety Key Plate| 2| | C26| Safety Key Holder 1| D19| Washer (8)| 9| E21|
IPAD Holder Sticker| 1
B11 Cylinder Fasten Roller| 1| | C27| Safety Key 1| D20| Spring Washer (8)| 2|
F01| Filter (Optional)| 1
B12 Pressure Spring| 3| | C28| Black Cushion 4| D21| Flat Washer (8)| 8| F02|
Inductance (Optional)| 1
B13 Pull Spring| 1| | C29| Side Rail Holder 6| D22| Bolt (M830)| 2| F03| AC
Single Wire (Optional)| 1
B14 Bushing| 2| | C30| Adjustable Foot Pad 2| D23| Flat Washer (12)| 1| F04|
Grounding Wire (Optional)| 1
B15 Guide Bar| 2| | C31| Black Cushion 4| D24| Screw (ST2.56)| 4| F05| Screw
(Optional)| 4
B16 Compression Spring| 2| | C32| Cover Button 2| D25| Bolt (M640)| 4| G01|
Belt Guide Hook| 2
B17 Limit Bushing| 2| | C33| Ring-shaped Wire Plug 2| D26| Screw (ST2.96)| 7|
G02| Screw| 4
B18 Cross wrench/Screwdriver| 1| | C34| Foot Pad 2| D27| Flat Washer (10)| 1|
H01| USB Connection Wire (Optional)| 1
B19 5# Allen Wrench| 1| | C35| Transport Wheel 2| D28| Nut (M10)| 1| H02| USB
Module (Optional)| 1
B20 Rotate Bushing| 2| | C36| IPAD Holder Clamp 1| D29| Bolt (M825)| 1| H03|
Speaker (Optional)| 1
B21 Pull Spring| 2| | C37| Spring Rope 1| D30| Bolt (M645)| 1| H04| Speaker
(Optional)| 1
C01 Motor Top Cover| 1| | C38| Running Belt 1| D31| Bolt (M815)| 4| H05| MP3
Wire (Optional)| 1
C02 Motor Bottom Cover| 1| | C39| Motor Belt 1| D32| Bolt (M512)| 4| H06| MP3
Power Wire (Optional)| 1
C03 Motor Side Cover-L| 1| | C40| Upright Tube Knob 2| D33| Bolt (M625)| 4|
H07| Screw (ST2.9*8) (Optional)| 10
C04 Motor Side Cover-R| 1| | C41| Folding Foot Pad 2| D34| Spring Washer (10)|
1| J01| USB Port Plug 1| 1
C05 Side Rail Ring-L| 1| | C42| Supporting Button 2| E01| Running Board| 1|
J02| USB Port Plug 2| 1
BUTTON FUNCTIONS
A. START: Press to start treadmill, the running belt will start moving.
B. STOP/PAUSE: Press to stop treadmill, the running belt will slow before
stopping completely.
C. PROGRAM: Selects the desired program (P1-P12, FAT).
D. MODE: To select countdown mode for distance, calories, steps and time.
E. SPEED +: Press this button to increase speed/value.
F. SPEED -: Press this button to decrease speed/value.
COMPUTER FUNCTIONS
MPH to KPH Conversion
In standby mode, remove the safety key then press and hold SPEED + and SPEED –
at the same time for 5 seconds. Speed will show ‘0.6’ for MPH or ‘1.0’ for
KPH. Repeat the above process to change again.
Safety Key
The machine will not operate unless the red safety key is inserted. If the safety key is out of place the machine will shut down immediately. The screens will display ‘- – – -’ with a warning tone. The clip on the end of the safety key must be attached to the user at all times during your workout to ensure the machine stops immediately in the event of emergency.
Display
When paused the console will display ‘PAU’.
During workout the left screen will alternate between displaying calories and
steps. The right screen will alternate between displaying pulse and speed.
Quick Start
Press START. The system will count down for 3 seconds and make a sound.
Press SPEED +/- to adjust speed.
Mode
Press MODE to enter TIME, DISTANCE, CALORIES and STEPS.
- Press +/- to set workout target value.
- Press START to begin workout out.
- Press SPEED +/- to adjust speed.
Body Fat Test
-
Press PROGRAM until you get to FAT.
-
Press MODE then use SPEED +/- to set target value: Set value from F-1-to F-4:
F-1 GENDER (01 Male / 02 Female)
F-2 AGE
F-3 HEIGHT
F-4 WEIGHT -
Press MODE to enter F-5 (F-5 BODY FAT TEST) hold hands on the pulse sensors, the console will display your body fat value after 3 seconds.
The body fat value is intended as a guide, and is not medical data:
≤ 19 Under Weight
20-25: Normal Weight
26-29: Overweight
≥ 30 Obese
Program
Press PROGRAM button, CALORIES/STEPS will display 12 programs, select between
P1-P12.
Press SPEED +/- to set the workout time.
Press START to begin workout.
Programs are divided into 10 sections; the machine will beep 3 times when
starting a new section.
Press SPEED +/- to adjust speed during each section.
When the program is finished the machine will beep 3 times then stop.
Power Saver Function
This product is manufactured in compliance with the Erp Regulations and is fitted with a power saving mode which will activate if the Treadmill is inactive for a period of 10 minutes. To restart the treadmill press any button.
Lubrication Reminder
After every 300km (188 miles) of running the treadmill will require lubricating. The machine will make a sound every 10 seconds and display ‘OIL’. Read the user guide for lubrication insturctions.. After lubrication, hold STOP for 3 seconds and the warning will be removed.
UK: RFE Europa Ltd. 8 Clarendon Drive, Wymbush, Milton Keynes, MK8 8ED.
+44 (0)800 440 2459 /
techsupport@rfeinternational.com
Europe: RFE Europa, Linprunstrasse 49, 80335 Munich, Deutschland.
serviceeuropa@rfeinternational.com
ES: +34 800 600 816 / serviciotecnico@rfeinternational.com
DE: +49 (0)89 189 39 700 / serviceeuropa@rfeinternational.com
APAC (excluding Australia): RFE Asia Pacific, 26F, 2608-2609, 1 Hung To
Road, Kwun Tong, Kowloon, Hong Kong.
+852 34685027 /
techsupportapac@rfeinternational.com
Australia: techsupportaustralia@rfeinternational.com
USA: RFE Sporting Goods Inc. 445 Plasamour Drive, Suite 1, Atlanta, GA
30324, USA.
+1 (800) 215 6216 /
techsupportusa@rfeinternational.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>