EPOMAKER EP84 75 Percent Hot-Swap Wired Wireless Mechanical Keyboard Instruction Manual

EPOMAKER EP84 75 Percent Hot-Swap Wired Wireless Mechanical Keyboard

This Quick Guide is an introduction to the use and functionality of the EPOMAKER EP84. For the software download, please visit the official epomaker website at:

https://epomaker.com/pages/software-downloads

Should you require more assistance please email us at support@epomaker.com

• MODEL: EPOMAKER EP84
  SIZE: 315 x 120.5 x 27mm

• NKRO: Yes

• SYSTEM: Windows / Mac

• CONNECTION: USB-C, 2.4GHz Bluetooth 3.0, Bluetooth 5.0.

• WEIGHT: 725g ± 20g

• hot swap: YES

• KEYCAPS: PBT

• LAYOUT: 84 Keys

GENERAL FUNCTION SHOR T CUT S

FN + 1| Bluetooth Device 1| | FN +| Backlight Brightness +
FN + 2| Bluetooth Device 2| | FN +| Backlight Brightness –
FN + 3| Bluetooth Device 3| | FN +| Backlight Effect Speed –
FN + 4| 2.4GHz Wireless| | FN +| Backlight Effect Speed +
FN + 5| Wired| | FN + HOME| Toggle the backlight color

CHANGE RGB EFFECTS

Pressing FN+Pause at the same time allows you to switch the RGB effect of your EP84 Keyboard.

PAIRING BLUETOOTH

• FN 1/2/3: Long Press for 3 seconds to pair Bluetooth device
• FN 1/2/3: Short Press to switch to last paired device

Long press the FN+1/2/3 for 3 seconds, the keyboard will start pairing and the light will flash. If there’s no connection, the keyboard will enter into sleep mode.

PAIRING WIRELESS 2.4GHz

FN 4: Switch to Wireless Mode

Firstly, turn on the keyboard via the switch on the keyboard’s bottom. Then plug the receiver into your device. After being recognized by your device, press FN+4, and you will see the 4 key backlit flashes. When the LED stays on the green, the pairing is Successfuly done.

BLUETOOTH & WIRELESS 2.4GHZ SPECIFICATIONS

The operating system should be windows 8 or above to support the Bluetooth function. The device should support Bluetooth 5.0 or a higher version to use Bluetooth 5.0.

KEYBOARD SHORTCUT

If you switch devices and/or systems, please make sure to press FN+A/S to switch the keyboard layout according to the system you used, or some shortcuts/multimedia keys may not work properly.

KEYBOARD WAKE UP/SLEEP

if your keyboard is sleeping press any key to wake it up, it will remember the last device connected.

REPLACING KEYCAPS AND SWITCHES

For a full guide on how to remove keycaps and switches scan the OR Code or type in your browser:

• https://epomaker.com/blogs/guides/diy-guide-how-to-remove-and-replace-your-mechanical-keyboard-switches

• Before installing switches, be sure the pins are clean and straight.

Included Tools

• Switch Puller
• Keycap Puller
• The Switch Puller tool aligns Vertically to the Switch to unclip the plastic securing the switch to the plate.

Remove Switches

1. Grab your Switch Removal Tool and align the gripping teeth vertically (on the Y-Axis) at the center of the switch, as shown in the example graphic above.
2. Grab the switch with the Switch Puller and apply pressure until the switch releases itself from the plate.
3. Using firm but gentle force pull the switch away from the keyboard using a vertical motion.

Install Switches

1. Check that all the switch metallic pins are perfectly straight and clean.
2. Align the switch vertically to have the Gateron logo facing north. The pins should align themselves to the keyboard PBC.
3. Press the switch down until you hear a click. This means your switch clips have attached themselves to the keyboard plate.
4. Inspect the switch to ensure it’s properly attached to your keyboard, and test it.

Note: If the key doesn’t work its possible you may have bent one of the switches while installing it. Pull the switch out and repeat the process.

Pins may be damaged beyond repair and need replacement if this process is not done correctly. Never apply excessive force when replacing keycaps or switches. If you cannot remove or install keycaps or switches please contact customer service as soon as possible to avoid damage to the keyboard due to operating errors.

TECHNICAL ASSISTANCE

For technical assistance, please email to support@epomaker.com with your purchase order number and a detailed description of your issue.

We normally respond to enquiries within 24 hours. If you purchased your keyboard from a distributor or not from any official store of Epomaker, please contact them directly for any additional help.

COMMUNITY FORUMS

Join our community and learn together with other keyboard enthusiasts.

• https://discord.gg/2q3Z7C2
• https://www.reddit.com/user/epomaker/

WARRANTY

EPOMAKER’s Warranty covers any factory defects that might affect the proper functionality of your purchase. It doesn’t cover any damage that may occur from normal wear and tear. If your product is defective we will send you a replacement unit. Replacement units might require you to send the defective unit back to Epomaker. We provide a 1 year warranty for our products when bought from our website (EPOMAKER.com). Your item will not be covered by your 1 year warranty if the inspection shows any sign of modification or changes unsupported by the original product, these include: Changing internal components, Assembling and reassembling the product, Replacing Batteries, etc. We will ONLY cover the item if it is bought from our official stores. You do not have a warranty with us if you bought the item from another reseller or likewise. Please contact the store that you bought your product from to resolve issues.

References

• ce.com
• Epomaker
• Epomaker
• Epomaker
• DIY Guide: How to Replace Your Mechanical Keyboard Switches
• Reddit - Dive into anything

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>