JONATHAN Y JYL1328V Lighting Fixture User Manual
- June 4, 2024
- JONATHAN Y
Table of Contents
JONATHAN Y JYL1328V Lighting Fixture
Product Specifications
- Model: JYL1328
- Product Dimensions: 14.5L X 14.5W X 11-70H
Preparation
Before beginning assembly of the product, ensure all parts are present.
Compare parts with the package contents list and hardware contents list. If
any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
If you have any questions regarding defects, missing parts, assembly issues, replacements, or device connectivity, please send a detailed email to cs@jonathany.com
Assembly Steps
- Unscrew the two canopy nuts (K) from the mounting bracket (A).
- Fasten the mounting bracket (A) onto the outlet box using two outlet box screws (B).
- Loosen the plastic screw (G) on the canopy assembly (H) by using a flat head screwdriver (not provided) and adjust.
Electrical Connection
Connect Hot (Black or Red) Outlet Supply Wire to: Clear, Brown, Gold or Black without Tracer (colored stripes)
Connect Neutral (White) Outlet Supply Wire to:
Clear, Brown, Gold or Black with Tracer (colored stripes)
Note: When parallel wire (SPT I & SPT II) is used, the neutral wire is
square-shaped and ridged while the hot wire will be round in shape and smooth.
WARNING
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
WARNING
SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER
BEFORE INSTALLATION.
INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR
CARE AND MAINTENANCE
To clean the outside of the fixture, use a dry or slightly dampened clean
cloth (use clean water, never a solvent) to wipe the surface of the fixture.
To clean the inside of the fixture, first disconnect power to the fixture by
turning off the circuit breaker or by removing the fuse at the fuse box. Next,
use a dry or slightly dampened clean cloth (use clean water, never a solvent)
to wipe the interior surface of the fixture. Do not use any cleaners with
chemical, solvents or harsh abrasives. Use only a dry soft cloth to dust or
wipe carefully.
NOTICE & IMPORTANT SAFETY INSTRUCTIONS
- Please make sure that you have all parts indicated before you begin assembly of this item
- This item should be assembled on a soft surface to prevent scratching the finish during assembly
- To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guideline below for safe use and installation
- The external flexible cable or cord of this luminaire cannot be replaced
Part List and Hardware List
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare
parts with package contents list and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 minutes.
If there are any questions relating to defects, missing parts, assembly
issues, replacements, or device connectivity issues, please send a detailed
email to cs@jonathany.com
- Unscrew the two canopy nuts (K) from the mounting bracket (A).
- Fasten the mounting bracket (A) onto the outlet box using two outlet box screws (B).
- Loosen the plastic screw (G) on the canopy assembly (H) by using a flat head screwdriver (not provided) and adjust
Connect,Hot,Black or Red outlet Supply Wire to:| Connect, Neutral, White
Outlet Supply Wire to:
---|---
Black| White
Parallel Cord(round&smooth)| Parallel Cord (square & ridged)
Clear,Brown,Gold or Black without Tracer(colored stripes)| Clear, Brown, Gold
or Black with Tracer (colored stripes)
Insulated Wire(not green)with copper metal conductor| Insulated Wire (not
green) with Silver metal conductor.
*Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
Grounding Instructions:
- For installation in the United States: Wrap ground wire from outlet box around green ground screw on mounting bracket, no less than 2″ from wire end. Tighten ground screw. If fixture is supplied with ground wire, connect to outlet ground wire with a wire connector.
- For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding screw on mounting bracket. Tighten ground screw.
- Attach the canopy assembly (H) to the mounting bracket (A) and fix it by turning the Canopy Nut (K) clockwise.
- Unscrew the socket ring (F) from the socket of the fixture body (E), please the metal cap (I) over the socket and secure with the socket ring (F).
- Insert the bulb (L) into the socket until secure.
- Please the shade (J) over the socket, rotate clockwise to lock, and secure the shade (J).
DO NOT EXCEED THE SPECIFIED WATTAGE.
PLEASUE USE TYPE “A” BULB MAX 25-WATT OR LED MAX 5-WATT, THERE IS LED 5-WATT
BULB IN THE BOX.
ENJOY YOUR LAMP
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>