PERAQUA Inlet Nozzle with Ball Acc DIN for Ocean Wall Condtuit PT Deluxe Instruction Manual

June 9, 2024
PERAQUA

**

PERAQUA-LOGO **

PERAQUA Inlet Nozzle with Ball Acc DIN for Ocean Wall Condtuit PT Deluxe

PERAQUA-Inlet-Nozzle-with-Ball-Acc-DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-
PRODUCT

Breaking the Nozzle in Various Diameters

The Ocean Inlet Nozzle comes with a ball that can be broken into two different diameters: 17mm and 21mm. To break the ball, use a hammer carefully.

Using the Multi-Purpose Spanner

The multi-purpose spanner should be used to screw and loosen the part. Follow the instructions carefully to ensure proper installation, operation, and maintenance of the inlet nozzles.

Sealing Plug Application

When applying the sealing plug, follow the instructions in section 6.1 of the manual carefully to avoid any damage to the inlet nozzles.

Warranty and Liability

All warranties for the Ocean Inlet Nozzles are in conformance with European Union rights.

General

Breaking the nozzle into various diameters

The ball can be broken in 2 different diameters. The original diameter of the ball is 13mm.
diameter 17mm: diameter 21mm:

The use of a hammer makes the breaking of the ball opening easier. However, the blow has to be carried out very carefully.

Screwing and loosening the part by using the multi-purpose spanner

For screwing the ring in and out (resp. also with the sealing plug) the multi- purpose spanner is used (part #.: 150420)

Steel wall pools

PERAQUA-Inlet-Nozzle-with-Ball-Acc-DIN-for-Ocean-Wall-
Condtuit-PT-Deluxe-FIG-4

(part #.: 170628) Individual parts:

  1. face plate
  2. Ocean multiflow ball (part #.: 150501)
  3. nozzle
  4. 2 x gasket
  5. washer
  6. locknut Rp 2”
Installation of the nozzle in the pool wall

PERAQUA-Inlet-Nozzle-with-
Ball-Acc-DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-FIG-5

Assembly instructions:

  1. Put the gasket on the nozzle and push it through the already punched hole in the steelwall with foil.
  2. One gasket and one washer have to be put onto the nozzle.
  3. Screw the locknut Rp 2” on to the nozzle so tight, that the gasket get slightly squeezed.
    • The screwing easier if the flexfit spanner is used. (part #.: 71635)PERAQUA-Inlet-Nozzle-with-Ball-Acc-DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-FIG-6
    • Caution : During the installation of the nozzle make sure that the procedure is done stress-free.
  4. If necessary, break the ball with a larger diameter (cf page 4, item 1.1). Put the ball in the housing and screw the face plate together with the housing by using the multi-purpose spanner (cf 1.2) Discharge angle resp. -direction of the ball opening are individually adjustable. The ball is fixed with the face plate.
    Caution: The ball must not be mounted laterally reversed. The small opening is always the discharge opening.

Liner Pools

(part #.: 170625a) Individual parts:PERAQUA-Inlet-Nozzle-with-Ball-Acc-
DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-FIG-7

  1. face plate
  2. Ocean multi-flow ball (part #.: 150501)
  3. 6 x TORX – screws
  4. nozzle
  5. gasket
  6. wall conduit

Installation of the nozzle in the liner pool:PERAQUA-Inlet-Nozzle-with-
Ball-Acc-DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-FIG-8

Assembly instructions:

  1. Stick on the protective film for construction
  2. Bring the wall conduit in the requested position
    • Note: Chemical resistance data to ABS are only to be used as a guideline, as changes in the composition of the medium( i.g.e: premixed concrete, concrete, silicon, foam,..) and operating conditions may cause variations. Always perform a compatibility test if you are not certain about the materials. No warranty claims based on the published chemical resistance chart will be accepted. The data are up to date and we reserve the right to changes based on new information.
  3. Before laying the pool foil, remove the protection film for construction.
  4. Put the flat gasket between wall conduit and pool foil.
  5. Nozzle and wall conduit are screwed together with the TORX M5 screws, that are included in the scope of delivery.
  6. Adjust the parts and finish screwing them together.
    • CAUTION when using an AKKU-screwdriver Recommended rpm = max. 500 rpm
    • Force = max. 2Nm
  7. If necessary, break the ball with a larger diameter (cf page 4, item 1.1). Put the ball in the housing and screw the face plate together with the housing by using the multi purpose spanner (cf 1.2). Discharge angle resp. -direction of the ball opening are individually adjustable. The ball is fixed with the face plate.
    Caution: The ball must not be mounted laterally reversed. The small opening is always the discharge opening.

Tile Pools

(part #.: 170626A) Individual parts:PERAQUA-Inlet-Nozzle-with-Ball-Acc-
DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-FIG-9

  1. face plate
  2. Ocean multi-flow ball (part #.: 150501)
  3. nozzle for tile pools
  4. wall conduit

Installation of the nozzle in a tile poolPERAQUA-Inlet-Nozzle-with-Ball-
Acc-DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-FIG-10

Assembly instructions:

  1. Stick on the protective film for construction

  2. Bring the wall conduit in the requested position

    • Note: Chemical resistance data to ABS are only to be used as a guideline, as changes in the composition of the medium( i.g.e: premixed concrete, concrete, silicon, foam,..) and operating conditions may cause variations. Always perform a compatibility test if you are not certain about the materials. No warranty claims based on the published chemical resistance chart will be accepted. The data are up to date and we reserve the right to changes based on new information.
  3. After concreting remove the protection film for construction.

    • Caution: When gluing the tiles, take care that the inside thread of the wall conduit does not get contaminated.
  4. The tiles can be glued so tight to the wall conduit, that the nozzle can still be screwed into the wall conduit and that the nozzle overlaps the tile edge (cf above drawing)
    The space between tiles and wall conduit ( resp. wall) has to be sealed appropriately. Nozzle has to be screwed into the wall conduit by using the multi purpose spanner (cf above drawing)

  5. If necessary, break the ball with a larger diameter (cf page 4, item 1.1). Put the ball in the housing and screw the face plate together with the housing by using the multi purpose spanner (cf 1.2). Discharge angle resp. -direction of the ball opening are individually adjustable. The ball is fixed with the face plate.

Caution: The ball must not be mounted laterally reversed. The small opening is always the discharge opening.

Polyester pools

(part #.: 170627a)

Individual parts:PERAQUA-Inlet-Nozzle-with-Ball-Acc-DIN-for-Ocean-Wall-
Condtuit-PT-Deluxe-FIG-12

  1. face plate
  2. Ocean multiflow ball (part #.: 150501)
  3. nozzle for polyester pools
  4. gasket
  5. washer
  6. locknut Rp 2“
Installation of the nozzle in a polyester pool

PERAQUA-Inlet-Nozzle-
with-Ball-Acc-DIN-for-Ocean-Wall-Condtuit-PT-Deluxe-
FIG-13

Assembly instructions:

  1. Put the nozzle with already slid on gasket through the already cut hole in the polyester pool wall.
  2. Slide one gasket and one washer onto the nozzle.
  3. Screw the locknut Rp2” on to the nozzle and screw so tight, that the gasket gets slightly squeezed. Using the Flexfit spanner (part #.: 71635) makes this process easier
  4. Glue in the pipe and leave it for approx. 1 hour.
  5. If necessary, break the ball with a larger diameter (cf page 4, item 1.1). Put the ball in the housing and screw the face plate together with the housing by using the multi purpose spanner (cf 1.2). Discharge angle resp. -direction of the ball opening are individually adjustable. The ball is fixed with the face plate.

Caution: The ball must not be mounted laterally reversed. The small opening is always the discharge opening (see above drawing).

Miscellaneous

Applying the sealing plugPERAQUA-Inlet-Nozzle-with-Ball-Acc-DIN-for-
Ocean-Wall-Condtuit-PT-Deluxe-FIG-14

Sealing plug with O-ring (Ø 45×2.5) (part #.: 100224)

Using the sealing plug:

  • Sealing the nozzle during wintertime
  • If a nozzle is planned, but not yet put into operation
  • To keep the sealing plug waterproof the O-ring (Ø 45×2.5)

www.peraqua.com

Documents / Resources

| PERAQUA Inlet Nozzle with Ball Acc DIN for Ocean Wall Condtuit PT Deluxe [pdf] Instruction Manual
Inlet Nozzle with Ball Acc DIN for Ocean Wall Condtuit PT Deluxe, Nozzle with Ball Acc DIN for Ocean Wall Condtuit PT Deluxe, Acc DIN for Ocean Wall Condtuit PT Deluxe, Ocean Wall Condtuit PT Deluxe, Wall Condtuit PT Deluxe, Condtuit PT Deluxe, PT Deluxe, Deluxe
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals