AES GLOBAL 603 Wall Desk Mount Audio Handset User Guide

: June 4, 2024
: AES GLOBAL

Table of Contents

AES GLOBAL 603 Wall Desk Mount Audio Handset
Portable Audio Handset
Portable Video Handset
CHANGING SETTINGS
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

AES GLOBAL 603 Wall Desk Mount Audio Handset

Portable Audio Handset

Call Another Handset

Press and the unit will display ‘HS1’, ‘HS2’, ‘HS3’, ‘HS4’ depending on how many handsets are coded in the system.
Then use the you can select the handset you wish to call and then press to start the call.

Change Ring Volume

Press and to increase or decrease the ring volume and then press to save.

Adjusting Relay time

Press Relay 2 button for 3 seconds, scroll through menu until you see ‘ti’.
Press to select ‘ti’ and adjust your relay times. Press to select your relay time. Press to end the process. Both relays will have the same relay time.

Voicemail
When a call is not answered within 40 seconds, the visitor can leave a message. Once complete, the handset will display the symbol. The unit can store up to 16 voice messages.

Change Ring Tone
Press and the handset will ring with its currently selected tone. Then you can press the and keys to cycle through the available ring tones. Then press to select and save the tone To listen to a voicemail, press . If there is more than 1 use and to select the message required and press to play. Press once to Delete the message or press and hold to delete all.

RE-CODING/ADDING EXTRA HANDSETS

Occasionally the system may need to be re-coded once installed. If the handset does not ring when the call button is pressed, the system may need to be re- coded.

( ● = FULL RE-CODE : STEP 1-5 )
(● = ADDING A HANDSET : STEP 3-5 )

Steps

Step 1) Press and hold the CODE BUTTON inside the Transmitter Module for 5 seconds until the audible tone is heard from the Intercom speaker (On 603 Transmitter the blue LED marked Di7 should also flash.)
Step 2) Then press the CODE BUTTON 14 times and wait until the melody is heardor the LED turns off. Performing this step will remove ALL handsets currently synced (or partially synced) to the system. (Note: Doing this step will also clear ALL voicemails after reset. )
Step 3) Press and hold the CODE BUTTON inside the Transmitter Module for 5 seconds until the audible tone is heard from the Intercom speaker. (On 603 Transmitter the blue LED marked D17 should also flash.)
Step 4) Then press and hold the CODE BUTTON on the handset until the red LED at the top begins to flash, after a few seconds you will hear a melody play to let you know it has Successfully connected. (Repeat Steps 3 & 4 for each new handset. ,
Step 5) Finally you should test the kit to ensure that everything is working as expected by pressing the Call Button on the CallPoint to ensure the handset and/or wall mounted unit receives the call and that the two way speech is functioning correctly.

Wall/Desk Mounted Audio Panel (603 / 703 / 705)

Portable Video Handset

When the intercom is being called, identify the visitor on the screen.
Press the button to answer the incoming call.
Speak clearly into the top of the handset at a distance of 10-20cm.
During the call press or increase or decrease the volume.
Press the to release the door/gate and press to end the call.

CHANGING SETTINGS

The following settings can be changed on the handset at any time.

Adjusts brightness.
English, French or German.
Listen or delete Voicemail.
Change the ring tone.
Change screen colour.
Use up and down arrows to navigate, press OK to select.
Press right arrow at any time to exit or cancel change.

Brightness
Language
Messages
Bell
Colour

RE-CODING/ADDING EXTRA HANDSETS

Occasionally the system may need to be re-coded once installed. If the handset does not ring when the call button is pressed, the system may need to be re- coded.

( FULL RE-CODE: STEP 1-5)
(ADDING A HANDSET : STEP 3-5)
Step 1) Press and hold the CODE BUTTON inside the Transmitter Module for 5 seconds until the audible tone is heard from the Intercom speaker. (On 603 Transmitter the blue LED marked D17 should also flash.)
Step 2) Then press the CODE BUTTON 14 times and wait until the melody is heard or the LED turns off. Performing this step will remove ALL handsets currently synced (or partially synced) to the system. (Note: Doing this step will also clear ALL voicemails after reset.)
Step 3) Press and hold the CODE BUTTON inside the Transmitter Module for 5 seconds until the audible tone is heard from the Intercom speaker. (On 603 Transmitter the blue LED marked D17 should also flash.)
Step 4) Then press and hold the CODE BUTTON on the handset until the red LED at the top begins to flash, after a few seconds you will hear a melody play to let you know it has successfuly connected. (Repeat Steps 3 & 4 for each new handset.)
Step 5) Finally you should test the kit to ensure that everything is working as expected by pressing the Call Button on the CallPoint to ensure the handset and/or wall mounted unit receives the call and that the two way speech is functioning correctly.

( Video Handsets must be added first and 1 MAX )