EAE XD100 Presence Motion Brightness Sensor Instruction Manual

: June 1, 2024
: EAE

Table of Contents

Connection
Description of Devices
Technical Data
Operation and Display
Installation
Commissioning
Cleaning
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EAE XD100 Presence Motion Brightness Sensor Instruction Manual

Installation Manual XD100 Flush Mount (PD100, MD100)

EAE KNX Presence/Motion & Brightness Sensor

Connection

KNX connection terminal
KNX programming button
Programming LED
Blue movement LED

Description of Devices

XD100 KNX Presence/Motion Sensors are ideal for interior rooms such as medium to large-size offices, classrooms, conference and meeting rooms, parking buildings, warehouses and sport halls. Detector is available in two models; “Presence Brightness Sensor PD100” and “Motion Brightness Sensor MD100”. Presence Sensor PD100 is suitable in order- to detect minor movements in a smaller detection range. On the other hand Motion Sensor MD100 is suitable to detect larger movements. Both models provide the following functions;

Constant light function
Corridor function
Independent presence channel
HVAC channel
Master/Slave operation
Fully automatic-semi automatic operating mode
Test and calibration mode

Technical Data

Type of protection	IP 20	EN 60 529

Operation and Display

Programming Led (3)
Red led lights up after the programming button is pressed.
Movement Led (4)
Blue led lights up when a motion is detected.

Installation

Use a hole saw with diameter of 76 mm in order to install the box of sensor on the ceiling. KNX connector must be connected to the KNX connection terminal. Ensure that coloured cables are connected to terminals accurate.

Detection range depends on movement types. These types are divided as follows;
A) Sitting position in working desk height (0,8m)
B) Walking straight to the detector
C) Walking across the detector
D) Area of the brightness measuring in working desk height (0,8m)

Table 1 – MD100

M| A| B| C| D
5.0m| –| 9 m| 15 m| Ø3.0
4.0m| –| 8 m| 13 m| Ø2.3
3.5m| –| 7,5 m| 12 m| Ø2.0
3.0m| –| 7 m| 10,5 m| Ø1.6
2.5m| –| 6,5 m| 9m| Ø1.2
5.5m| –| 12m| 18m| Ø3.3
Table 2 – PD100

M| A| B| C| D
4.0m| 7,8 m| 7 m| 12 m| Ø2.3
3.5m| 7,3 m| 6,5 m| 10 m| Ø2.0
3.0 m| 6 m| 6 m| 8 m| Ø1.6
2.5m| 5 m| 5 m| 6 m| Ø1.2

Detection Range

Commissioning

Determination of the physical address and setting of parameters are actualized with Engineering Tool Software (ETS5 or higher). “.knxprod” file must be imported to the ETS. Please check website for latest “.knxprod” file. www.eaetechnology.com A detailed information about parameter configuration can be found in
Product Manual of device.
Installation and commissioning of device may only be implemented by trained electricians. The relevant standards, directives, regulations and instructions must be observed when planning and implementing the electrical installation.

When connecting the device make sure that the device is isolated!
Protect the device against moisture, dirt and damage during transport, storage and operation!
Do not operate the device out of the specified technical data which is stated.
The device may only be operated in closed enclosures (Distribution boards etc.)

Cleaning

If device becomes dirty, only a dry cloth can be used for cleaning. It is not suitable to use wet cloths, caustics and solvents.

© EAE Technology
Ikitelli Org. San. Bolg. Ziya Gokalp Mah. Eski Turgut Ozal Cad.
No: 20, Zip Code: 34490 Basaksehir/Istanbul Tel: +90 212 549 97 13
www.eaetechnology.com