NEXTECH QC3893 Wi-Fi Battery Powered Cameras Instruction Manual
- June 12, 2024
- Nextech
Table of Contents
0C3893
1080p Wi-Fi Battery
Twin Pack Cameras
Instruction Manual
Box Contents
2 x Wi-Fi Battery Powered Cameras
2 x Wall Mount Brackets
2 x USB Charging Cables
2 x Wall Mounting Hardware
| Solid red light | Setup Failure |
|---|---|
| Rod light blinking quickly | Pairing Mode |
| Green light blinking quickly | WI-Fi is connecting |
| Solid green light | Working normally |
| Yellow light blinking quickly (Red and green aght) | Device upgrade |
| Solid white light | Charging |
| White light blinking | Charging incorrectly |
Install APP
Download
APP: scan the QR code below to download and install Register and login: open
the * Smart Life” APP to register and login according to the guide in the APP.
http://smartapp.tuya.com/smartlife?from=singlemessage&isappinstalled=0
Add The Device-Scan QR code mode
Make sure Wi-iisavalable and connected to the Inernet.
Connect the camera to the power, then system startup completed.
Open “Smart Life” APP, press the’+ n the upper right comer of the main screen
(Figure 01) choose Security & Video Suveflance’, cick Smart Camera® (Figure
02) to add camera; and then dlick “Next step” (Figure 03)
If the mobile phone is not connected to Wi-Fi, please click “Connect o WiHi”
(Figure 04);
It will jump to the WLAN interface and connects Wi-Fi (Figure 05).
If the phone is connected to Wi-Fi (Figure 06), Tap “next” ;
Note: Only 2.4GHZ Wi-Fi s supported.
AR cade will prompt on phone screen and you need to scan it with the ‘Smart
Camera. (the camera is about 20-30 cm away from the mobile phone screen). Then
tap “I heard a prompt” (Figure. 07.
Gamera s “connecting’ (Figure. 08)
Connection completed Figure 09), tap “Done”” Itjumps to preview page
(Figure 10) After closing the device preview page, it eturns to the APP home
page.
Atthis time, the connected device will appear on the APP home page (Figure
11),
Then you can tap directly to the device page to monitor.
Add The Device- AP Mode
Select *AP Mode” (Figure 12)
Click Next (Figure 13)
Enter the account and password that can connect to WIFI (Figure 14) 
- Click *Go Connect” (Figure 15)
- Go to “Smart Life-XXXX “and click Connect (Figure 16)
- Connecting (Figure 17)
Click to complete the connection (Figure 18)
Video screen (Picture 1)
Reset
Press and hold the reset button for up to 10 seconds to reset the camera back to default settings.
Safety
- Do not open the case of this product to prevent the unit from damage.
- Keep the camera away from high temperatures as it may damage the device.
Specifications
| Image Sensor: | 1/2.0″ CMOS |
|---|---|
| `Resolution: | 1080p (1920 x 1080) VGA (640 x 480) |
| Frame Rate: | 15fos |
| Lens: | 4mm |
| Lens Angle: | 105° |
| Night Vision: | 6 x IR LEDs |
| Night Vision Range: | Up to 10m |
| Wi-Fi Frequency: | 2.40Hz |
| tmicroSD Card: | Up to 128GB |
| IP Rating: | IP65 |
| Battery: | 3.7V Li-ion, 5200mAh |
| Battery Life: | Up to 3 Months |
| Power: | 5VDC. 2A |
| Dimensions: | 130(L) x 78(H) x 70(W)mm |
Distributed by:
Electus Distribution Pty Ltd
46 Eastern Creek Dr,
Eastern Creek NSW 2766 Australia
Ph 1300 738 555
Int1 +61 2 8832 3200
Fax 1300 738 500
www.electusdistribution.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>