HORIZON MH50 4G LTE Mobile Hotspot User Manual

HORIZON MH50 4G LTE Mobile Hotspot

Specifications

• Model: MH04
• Network: TDD-LTE/FDD-LTE/WCDMA
• Functions: Data access, SMS, Micro SD card support (mobile USB disk)
• Features: Multi-network modes, UI support for SMS and Phone book, RNDIS mode, MODE function, firewall function, fast boot, power-saving mode

Function description

MH04 is a high-speed portable 4G router. MH04 provides data access and SMS functions such as TDD-LTE/FDD-LTE/WCDMA.At the same time, MH04 series support Micro SD card, which provides mobile USB disk function.

MH04 main features

• Support TDD-LTE/FDD-LTE /WCDMA etc, multi-network modes.
• UI support SMS and phone book function.
• Support RNDIS mode: plug into the PC and connect with the network without using modem mode dial-up.
• Support MODE function. With MODE, users can simply and securely connect to WIFI.
• Support firewall function which provides address filtering, port mapping, UPnP, DMZ, and other functions.
• Support fast boot. When it is set to the fast boot mode, the device will take a short time to boot.
• Support power-saving mode, you can set the WIFI coverage capacity to adjust the battery life.

Interface and LED status indicator description

1

|

Display screen

| Display the information of signal, network connection

type, power, etc

2| MODE button| For starting MODE function
3| Switch button| For turning on and turning off

4

|

Micro USB interface

| 1. for charging router

2. Connect the PC through the USB cable to provide USB Disk function and RNDIS Internet mode

5| SIM card slot| For installing SIM card
6| Reset hole| For factory reset

SIM card and installation
Please use the Micro SIM card, and SIM card chip into the SIM card slot down.

UI software installation and use

UI software introduction
UI software can be used to query settings network and device parameters, send and receive text messages, manage the phone book, view traffic and other operations. The initial login password for the UI software is “admin”.

UI software installation

Connect MH04 with PC ,UI software will install automatically

When installation is complete, the UI software desktop icon will be shown on the PC desktop.

Notes If the installation file does not automatically start, please find the new CD-ROM drive in the computer (as shown in Figure 4-3), click open and run the installation program to complete the first installation.

If you can not automatically install or can not find the new CD-ROM drive, there may be anti-virus software to prevent the installation of the software, please close the anti-virus software check. It is also may be a problem with the computer USB port, please replace the USB port or replace the computer and try again.

UI software use
Insert the MH04 into the computer where the UI software is installed and the UI software will start automatically. On the login page, enter the password and then log in, the page jumps to UI home page, the initial login password of UI software is “admin”. There are language options at the upper right corner of the UI, the user can choose Chinese or English according to need. Users can manually double-click the desktop UI software shortcuts, you can also open the browser, and enter 192.168.100.1 in the address bar to open the UI login page.

UI management page is divided into the status bar and the main interface. Status bar: network type, signal strength, network connection status, SIM card status, WLAN status, battery status and contains the Modify Login Password button, the Exit button, and the Language selection button. Main interface Home: including SMS, phone book, SD card, advanced settings, quick set entry button. All these buttons can be clicked to enter the corresponding interface; network connection bar: display network connection status, current real-time traffic, network connection time, network connection button can on and off network; network setting bar: including setting of external network connection and wireless internal network port; access Device column: Displays the number of users currently connected to the wireless terminal; Traffic Statistics column: Displays the traffic statistics information; Status Display Bar: Displays the detailed information of the device. Scan the two-dimensional code to obtain hot name, password and other information.

Note: In the settings interface, click the “question mark” icon you can open the specific menu item to use the help tips.
Users can use the computer, mobile phones, and other terminal equipment, to access MH04 WIFI hotspots, without installing the UI software can also access the UI page, open the browser, enter 192.168.100.1 in the address bar to open the UI login page after entering the password to log in to normal access.

Internet Access

1. Check if the SIM card is installed correctly.

2. Press and hold the on/off button for 3 seconds, and the indicator will flash and release the button.

3. Establish a WIFI connection between the terminal device and the MH04 device.

   • Find the WIFI hotspot on the computer, tablet, mobile phone, and other terminal devices. Find the WIFI hotspot name (ie SSID) provided by
   • MH04 : 4G MIFI_XXXX, where XXXX is the last four digits of the MH04 MAC address. Select the WIFI hotspot and connect.
   • The initial password for the WIFI connection is located on the back of the Mi-Fi label and can also be accessed through the Mi-Fi Display Menu. This can be done by pressing the mode button, where the SSID and WIFI Key information is displayed.

4. Log in to the UI software to check the 4G/3G network connection status.

5. If 4G/3G network dialing is set to “Auto” mode (factory setting), MH04 will automatically connect to 4G/3G network, users can view the network connection traffic on the home page of UI software.

6. If the 4G/3G network connection mode is set to “manual” mode, the user needs to manually connect to the 4G/3G network on the home page of the UI software. If the 4G/3G network connection is successful, the management page of the home page will show the network connection traffic.
   Note: The “Auto”/ “Manual” mode is set in the “Network Settings -> Connection Mode” menu of the UI software. The default is “Auto” mode.

7. When the MH04 is successfully connected to the 4G/3G network and the terminal device is successfully connected to the WIFI hotspot of the MH04 device, the terminal devices such as mobile phones, tablets, and computers can enjoy 4G/3G access.
   Note:
   If the MH04 is plugged into the computer, the computer does not have to connect WIFI hotspots can also be connected through the MH04 external network. If it cannot connect with the network, please check the following steps:

8. Please check your PC’s Device Manager -> Network Adapter for a new network card device, similar to a “Remote NDIS-based Internet Sharing Device”,
   as shown in Figure 5-1. Different computer shows the name of the card is different, you can compare the plug through the MH04 to see if there is a new network card.

9. If you have the above new network card device, but the device icon at the “!” Marked, please re-plug the MH04.

10. If there is no new network card device, please check whether the computer has a new CD-ROM drive (UI software installation disk). If so, right-click the drive letter, select the “pop-up” menu, eject the disc, and then return to step 1) to check whether there is a new network card and its status.

Use the MODE function

1. Click the “WI-FI Setting” item on the Web UI management page to enable the MODE function after selecting the PBC and clicking Apply. After setting, you can find the WIFI hotspot provided by the MH04 device by searching the MODE-enabled wireless terminal device. Click connection can easily access WIFI hot spots.
2. Enable the MODE function by the MODE button on the device, find the WIFI hotspot on the MODE-enabled wireless terminal device, locate the WIFI hotspot name provided by the MH04 device, select the WIFI hotspot, and then press and hold (3-4 seconds) MODE button on the device, you can easily access WIFI hot spots.
3. In the WI-FI Settings item of the Web UI management page, enable the MODE function and select the PIN. On a wireless terminal device that supports the MODE PIN entry function, click Advanced option of the WLAN settings to enter the submenu and select MODE PIN code input, pop up the generated PIN code, then input the generated PIN code in the input bar of MODE option in the UI management page, and then click Apply to connect the wireless terminal device to the WIFI hotspot provided by the MH04 device

Use the USB disk function

1. Check if the TF card is installed correctly.
2. The automatically added removable disk in the computer is called the TF card

Trouble Shooting

Unable to register to the network
Maybe the network signal is poor, see the signal strength is weak (such as only one cell signal), please move to the signal good place.

Log in WEB failure

1. The browser’s cookies and local temporary files are not cleared. For the IE8 browser as an example, open the IE browser, in Tools> Internet Options> General, click the Delete button in the pop-up to delete the history of the dialog box to check the Internet temporary file option and Cookie option, click the delete button to delete it, and then reopen the browser.
2. The home agent is not closed. Open your browser, go to Tools> Internet Options> Connections> LAN settings, close the proxy server, and then reopen your browser.
3. The possible TCP/IP protocol stack setting is set to “IPV6 only”. Local Area Connection – Properties – Open IPV4 support.

Unable to browse web pages

1. (U) The SIM card is in arrears. Please consult the relevant operator.
2. The flow is exhausted. If you want to continue to use the network, you can use the “Traffic Limitation Settings” interface to modify the national, local, provincial, Province, the additional flow value, the remaining flow, so that the remaining total flow> 0, or ” Default Action Over Monthly Flow ” to “keep this connection.”

Fail to connect with the corresponding WLAN hotspot

1. The access password is incorrect. Ensure that the password is correct. If you forget the password, you can log in to the Web UI through USB to reset it.
2. The system keeps a record of the previous wireless network. Clear wireless connection records, in the view of the wireless network interface, click Change the order of preferred network, delete the corresponding hot spots in the preferred network, confirm, and then research.

USB or WLAN Internet connection rate is unstable or too low

1. The network signal is weak. Please move to a place with a good network signal.
2. The network is busy during this period. Use when the network is idle.

Users couldn’t use the network.

1. The WLAN is not connected or the connection has failed. Make sure your Wi-Fi connection is successful.
2. The computer has multiple wireless network card devices enabled. Disable redundant, enabled wireless network card devices.

Wireless devices couldn’t find the corresponding WLAN hotspot
The system Wireless Zero Configuration service is turned off. In Control Panel> Performance and Maintenance Management Tools> Services, start Wireless Zero Configuration.

Forgot the UI software login password
When the user forgets the password, use the ejector pin to insert the reset hole of the device to restore the factory settings. The default password is “admin” when the factory default settings are restored.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

FCC Warning:

• Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions to satisfy RF exposure compliance.
• The device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when hotspot (10mm) is 1.371 W/kg.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>