JONATHAN Y JYL6304B Black Nelle 3 Light 18 Wide LED Antler Candle Style Chandelier Installation Guide

JONATHAN Y JYL6304B Black Nelle 3 Light 18 Wide LED Antler Candle Style

Chandelier

Product Specifications:

• Item Number: JYL6304
• Parts Included: Plastic wire connector (3), Hex nut (2), Green ground screw (1), Mounting plate (1), Mounting screw (2), Threaded nipple (1), Canopy (1), Screw collar loop (1), Quick link (2),Threaded ring (1), Chain (1), Loop (1), Antler chandelier main body (1), Bulb (3)

Product Usage Instructions

Assembly & Installation Instructions:

1. Check Parts: Carefully remove the fixture from the carton and ensure all parts are included.
2. Assemble Parts:
3. Fix threaded nipple into the screw collar loop.
4. Thread the mounting plate over the other end of the threaded nipple.
5. Secure the mounting plate in place by tightening the hex nut,ensuring the side marked GND faces the screw collar loop.
6. Pre-Installation:
7. Connect loops on the antler chandelier main body using quick links.
8. Determine correct chain length needed and attach it to the chandelier.
9. Installation:
10. Attach mounting plate to the outlet box with mounting screws.
11. Raise the canopy through the screw collar loop and position it correctly.
12. Attach the threaded ring and canopy to the chain.
13. Connect wires according to the provided instructions, ensuring correct wire connections.

Frequently Asked Questions (FAQ):

Q: Do I need a licensed electrician for installation?
A: It is suggested to have the installation done by a licensed electrician for safety reasons.

Q: Can I connect wires to ground wires?
A: Never connect wires to ground wires. Follow the provided chart for proper wire connections.

Item Number: JYL6304

WARNING (To reduce the risk of fire, electric shock, or injury to persons):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. A). Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. B). Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before fixture.

6. Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
   Please use Type “B” Bulb max 40-watt or CFL Bulb max 13-watt or LED Bulb max 9-watt there is LED 3pcs 4-watt Bulb in the Box.

7. Keep the lamp away from acidic and basic objects in case of damaging the surface of the lamp.

8. When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
   If there are any questions relating to defects, missing parts, assembly issues, replacements, or device connectivity issues, please send a detailed email to cs@jonathany.com

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED):
Before doing assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

• (A) Plastic wire connector (3)
• (B) Hex nut (2)
• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Mounting screw (2)
• (F) Threaded nipple (1)
• (G) Canopy (1)
• (H) Screw collar loop (1)
• (I) Quick link (2)
• (J) Threaded ring (1)
• (K) Chain (1)
• (L) Loop (1)
• (M) Antler chandelier main body (1)
• (N) Bulb (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration
2. Make assembly
   If the group of parts are not already assembled:

Step A1: Fix the threaded nipple(F) into the screw collar loop(H)

Step A2: Thread the mounting plate(D) over the another end of threaded nipple(F) ,

Step A3 :Place and tighten the hex nut(B) to secure the mounting plate(D) in place.At this point, the side of mounting plate marked “GND” must face to the screw collar loop(H).

Make pre‐installation

Step B1: Open the quick links (I) to connect the loops (L) on the antler chandelier main body(M),and to connect the loop(L) Close the quick links(I)

Step C1: By measuring,determine the correct length of links needed. Use the chain pliers,open and discard the remaining chain.

Step C2: Attach a quick link(I) to the loop(L) above the antler chandelier main body(M) and to connect the end of chain(K).

Step C3: Gently lace wires through chain(K) to the top of the another quick link(I) and pull tillsung

Turn off power

Make installation

Step C1: Attach Mounting plate(D) to outlet box with mounting screws(E). The side of single bar marked “GND” must face out

Step C2: Raise the canopy(G) through screw collar loop(H) and screw the collar loop(J) to a proper position by measuring.Unscrew threaded ring(J) from screw collar loop(J) and remove the canopy(G).In this way, you would know the proper position on which collar loop it should be located.

Step C3: Slip threaded ring(J) over the chain(K), then do the same with the canopy(G)

Step C4: Open the quick link(I) then attach to the collar loop(H). Close the quick link(I)
Pass the wires through collar loop(H) to the mounting plate, gently pull the tillsung

Step C5: Make wire connections
Connect wires as below wires connecting shown. TAKE NOTE OF YOUR COLOR OF FIXTURE,NEVER

CONNECT WIRES TO GROUND WIRES

Connect ground wire according to below chart Connect ground wire according to below chart

Twist plastic wire connector(A) until wires are tightly joined together, wrap each connector with approved electrical tape for more secure connection and carefully stuff all wires into the outlet box

Step C6: Raise canopy(G) to ceiling and secure canopy(G) in place by tightening threaded ring(J) onto screw collar loop(H)

Step C7: Install bulb (N) (Please do not exceed the maximum capacity recommended on the socket.)

Check everything is already installed properly, then you could turn on the light.

CLEANING

To clean, wipe fixture with a soft cloth,Do not use abrasive materials such as scouring pads or powders,steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to order replacement parts.
All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>