JONATHAN Y JYL1507 Hollis 3 Light 24 Wide LED Vanity Light Set Instruction Manual

JONATHAN Y JYL1507 Hollis 3 Light 24 Wide LED Vanity Light Set

Product Usage Instructions

• Preparation:
  • Before beginning assembly of the product, ensure all parts are represented. Compare with the part list and hardware list provided. Do not attempt assembly if any part is missing or damaged.
• Estimated Assembly Time: 20 minutes
  • If you have any questions or issues, please contact cs@jonathany.com.
• Installation Steps:
  • Separate the mounting plate (B) from the lamp body (F) by removing the screwed ball (E) anti-clockwise. Fix the mounting plate (B) to the outlet box with machine screw (D).
  • Make wire connections using wire connectors (A) as per the reference chart provided in the manual.
  • Secure the lamp body (F) to the mounting plate (B) with the provided screws (E).
  • Attach the glass (H) to the socket cap and secure it with the ball screw (G).
  • Install the bulb (I) following the specified wattage guidelines. Ensure the electrical current is turned off before changing bulbs.
• Specifications for Bulb Usage:
  • Please use an on/off type A bulb max 40-watt or LED bulb max 9 watts. There are 3 pieces of 4-watt LED bulbs included in the box.

FAQs

• Q: Can I return the item if it has been installed?
  • A: No, the item may not be returned once it has been installed.
• Q: What should I do if I find any damage or defect in the product?
  • A: Do not attempt to install the product if there is any damage or obvious defect. Contact customer service for further assistance.
• Q: How should I handle grounding during installation?
  • A: Follow the grounding instructions provided in the manual based on your location (US or Canada)

SPECIFICATION

• Model#: JYL1507
• Product Dimensions: 23.75″W X 6.5″EX 11.5″H

WARNING

• WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN.
• WARNING SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION.
• INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT, DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED.

CARE AND MAINTENANCE

• To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
• To clean the inside of the fixture, first disconnect the power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box.
• Next, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the interior surface of the fixture.
• Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

IMPORTANT SAFETY INSTRUCTIONS

NOTICE & IMPORTANT SAFETY INSTRUCTIONS

• Please make sure that you have all parts indicated before you begin assembly of this item
• This item should be assembled on a soft surface to prevent scratching the finish during assembly
• To reduce the risk of fire, electrical shock or injury to persons or property, please follow the guidelines below for safe use and installation
• The external flexible cable or cord of this luminaire cannot be replaced
• If the cord is damaged, the luminaire shall be destroyed.

Part List and Hardware List

PREPARATION

Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 20 minutes. If there are any questions relating to defects, missing parts, assembly issues, replacements, or device connectivity issues, please send a detailed email to cs@jonathany.com.

1. Separate the mounting plate (B) from the lamp body (F) by removing the screwed ball (E) anti-clockwise. then fix the mounting plate (B) to the outlet box with machine screw (D).
2. Make wire connections, with wire connectors(A), following the reference chart listed below.
   Connect, Hot, Black or Red Outlet Supply Wire to:| Connect, Neutral, White Outlet Supply Wire to:
   ---|---
   Black| White

• Parallel Cord (round & smooth)| Parallel Cord (square & ridged)
  Clear, Brown, Gold or Black without Tracer (coloured stripes)| Clear, Brown, Gold or Black with Tracer (coloured stripes)
  Insulated Wire (not green) with copper metal conductor| Insulated Wire (not green) with Silver metal conductor.
  • Note: When parallel wire ( SPT I & SPT II ) is used. The neutral wire is square shaped and ridged and the hot wire will be round in shape and smooth. ( See Illustration on left. )
  • Grounding Instructions:
  • a) For installation in the United States: Wrap ground wire from the outlet box around green ground screw (C) on the mounting plate, no less than 2″ from the wire end. Tighten the ground screw. If the fixture is supplied with a ground wire, connect it to the outlet ground wire with a wire connector.
  • b) For installation in Canada: If the fixture is supplied with ground wire, wrap ground wire around the green grounding screw on the mounting plate. Tighten the ground screw.
  3. Orient the ceiling canopy of the lamp body (F) so that the mounting screws protruding from the mounting plate (B) go into the holes in the canopy of the lamp body (F), then secure it with the provided screwed balls (E).
  4. Attach the glass (H) to the socket cap and then fixed using the ball screw (G).
  5. Install bulb (I). Be sure to use light bulb(s) with wattage no greater than specified on this fixture. Always make sure that the electrical current is turned off before changing bulbs.

INSTALLATION

Installing the towel ring

1. Determine the location for the towel ring (P). Using the short mounting bracket (K) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, allowing for the wood screws (M) to protrude through the hole on the short mounting bracket (K), then screw the wood screw (M) to the wall anchors (J).
2. Place the towel ring (P) over the short mounting bracket (K) and use the hex key (O) to secure it in place by using a screw (N).

Installing the robe hook

1. Determine the location for the robe hook (Q). Using the short mounting bracket (K) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, allowing for the wood screws (M) to protrude through the hole on the short mounting bracket (K), then screw the wood screw (M) to the wall anchors (J).
2. Place the robe hook (Q) over the short mounting bracket (K) and use the hex key (O) to secure it in place by using a screw (N).

Installing the toilet paper holder

1. Determine the location of the toilet paper holder (R). Using the long mounting bracket (L) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, allowing for the wood screws (M) to protrude through the hole on the long mounting bracket (L), then screw the wood screw (M) to the wall anchors (J).
2. Place the toilet paper holder (R) over the long mounting bracket (L) and use the hex key (O) to secure it in place by using a screw (N).
   • NOTE: The toilet paper holder Can be installed in left and right instal.

Installing the towel bar

1. Place the towel bar (T) to the body of the towel bar (S).
2. Determine the location of the body of the towel bar (S). Using the long mounting bracket (L) as a template, mark the location of the holes for the wall anchors (J). Drill the appropriate size holes for the wall anchors (J). (the holes should be slightly smaller than the size of the wall anchors (J). ). The wall anchors (J) are then punched into the drilled holes, allowing for the wood screws (M) to protrude through the hole on the long mounting bracket (L), then screw the wood screw (M) to the wall anchors (J).
3. Place the body of the towel bar (S) over the long mounting bracket (L) and use the hex key (O) to secure it in place by using a screw (N).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>