MOLD PRESS AB661033 Vacuform Machine Instruction Manual
- June 3, 2024
- MOLD PRESS
Table of Contents
MOLD PRESS AB661033 Vacuform Machine
WARNINGS
- Heating element of Mold Press’M will burn your skin if you touch it Wear Heat Resistant Gloves to protect against burns.
- Always tum off machine after use and albw to cool comp-,tely before handling.
- Never leave Mold Press”‘ unattended when in use.
- Always unplug machine when not in use.
- Use machine on an uncluttered, heat resistant, and level workspace.
- Operate Mold Press’M in a well-ventilated space. Plastic sheets, when heated, can emit fumes. If you are sensitive to fumes wear a mask.
- For best results and to avoid damage to machine, use plastic and materials sold by We R Memory Keepers
- Do not leave plastic sheets under heating element for longer than 5 minutes.
- Mold Press’M and vacuum cleaner cannot be plugged into same circuit.
- Do not immerse Mold Press’M in water or other liquid; danger of electric shock.
- Mold Press’M is not a toy and not intended for children.
- Mold Press”‘ has no customer serviceable parts.
- Use only for intended purposes.
- For household use only.
- Close supervision is required when this product is used near children.
- Place Mold Press• and connected cord so that is not likely to be overturned.
WHAT’S INCLUDED
- Mold Press1M Machine
- Magnetic Frame
- Vacuum Hose Adaptor (fits most at-home vacuums)
- 4 PETG Plastic Sheets (additional sheets sold separately)
MACHINE SPECIFICATIONS
- Recommended for plastics and materials sold by We R Memory Keepers
- Plastic sheet dimensions: 6.75 inches x 6.75 inches (17 cm x 17 cm)
- Forming area on machine: 5.5 inches x 5.5 inches (14 cm x 14 cm)
- Maximum height for molded items: Recommended not to exceed 2
- inches (5 cm)
- Machine dimensions: 9.25 inches x 8.5 inches x 10.75 inches (23.5
- cm x 21.5 cm x 27 cm)
- Standard input voltage: 120 volts
- Vacuum strength range: 5 amps to 10 amps
MOLD PRESS
ASSEMBLY
TIPS & TRICKS
- Use care any time your hands are in the machine, either placing object, removing object, handling plastic, or adding detail with tools. It is recommended to wear Heat Resistant Gloves (sold separately).
- For best results use plastic and other materials sold by We R Memory Keepers®. They have been tested and work best with machine. Other materials may damage machine.
- Heating time for PLASTIC SHEET S can vary depending on your environment and air temperature.
- Plastic objects with a smooth surface may not shape well during vacuform process. Use sandpaper to create a texture on the surface to improve air flow.
- lf placing multiple objects on VACUUM SCREEN do not place objects too close together in order allow to enough space for plastic to form around object
- For best results tightly hold MAGNETIC FRAMES together while lowering plastic.
- If plastic is sticking to object, dust object with Powder Release (sold separately).
- To remove wrinkles and form plastic into corners, use shaping tools while vacuum is still running and plastic is still warm.
- To form additional details from object, immediately use Heat Gun (sold separately) to keep plastic warm and malleable while vacuum is still running.
- If object has a lot of detail, let plastic cool up to a minute before removing from plastic.
- There are many variables in achieving the perfect mold. Shape, size, and finish of the object can impact the final result.
SAFETY INSTRUCTIONS
Undercuts, caused by a ledge around outside edge of an object, can prevent you from removing objects from form. Use Polymer Detail Clay (sold separately) to fill in any undercuts.
Objects with sharp angles may be difficult to remove from mold.v Angles less than 90 will not remove from mold.
Air pockets, caused by poor air flow around object, keep plastic from forming tightly around object. Add air holes to ensure plastic forms tightly.
WARRANTY
For a limited warranty register this product at: www.wermemorykeepers.com/warranty
STORAGE
- Mold Press’M should be completely cool before moving.
- To carry Mold Press’M lift from bottom of unit using both hands
- Cover VACUUM SCREEN when not in use to protect it from dust.
- Dust on surface of VACUUM SCREEN may impact results.
MAINTENANCE
- Clean Mold Press when cool with a clean, dry cloth. Do not use abrasive materials or liquids.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>