Apevia ATX-PR800W Prestige Power Supply User’s Manual
- August 20, 2024
- APEVIA
Table of Contents
Apevia ATX-PR800W Prestige Power Supply
Product Features
- Stable and reliable
- Cosmic black casing
- Supports single 12v output for higher power usage
- Supports Dual / Quad / Multi-Core CPUs
- Ample +12 V Output, and enhanced +12 V current capability broaden utilization possibilities.
- Multi-GPU technologies supported, 6-Pin and 8-Pin PCI-E connectors to support all GPU platforms
- Built-in 1 x 135mm silent automatic thermal fan speed-controlled black fan.
- Dimensions : 150mm x 86mm x 158mm (5.9″ x 3.4″ x 6.2″) W x L x H
- Heavy-duty protections, including OVP (Over Voltage Protection), OPP (Over Power Protection), SCP (Short Circuit Protection)
- Universal AC input by active PFC (99%RF Typical)
- DC to DC converter design, provides superior dynamic response, greater system stability, and maximizes the 12 V DC rail output.
Product Specifications
- AC input voltage: 115-230V
- AC input frequency: 60Hz/50Hz
- Operating temperature: The power supply should be operated in an ambient temperature of 0°C to 40°C
- DC output:
| Model | 600W Prestige Power |
|---|---|
| AC Input | 115-230VAC , 8A/4A , 50-60HZ |
| DC Output Voltage | +3.3V |
| Max Output Current | 20A |
| Combined Power | 100W |
| Total Power | 600W |
| Model | 800W Prestige Power |
| AC Input | 115-230VAC , 8A/4A , 50-60HZ |
| DC Output Voltage | +3.3V |
| Max Output Current | 20A |
| Combined Power | 100W |
| Total Power | 800W |
| Model | 1000W Prestige Power |
| AC Input | 115-230VAC , 8A/4A , 50-60HZ |
| DC Output Voltage | +3.3V |
| Max Output Current | 20A |
| Combined Power | 100W |
| Total Power | 1000W |
Overall Performance:
- Hold up time: 14ms at full load normal line input voltage.
- Switching frequency: 50KHz at normal line input.
- Stability: +/- 5% for 24KHR after warm-up.
Protections:
-
Under voltage protection. If an under-voltage fault occurs, the supply will latch all DC outputs into a shutdown state when +12V,+5V & +3.3V outputs under 60% of its maximum value.
-
Over-voltage protection
Output| Minimum| Nominal| Maximum| Unit
---|---|---|---|---
+12 VDC| 13.4| 15.0| 17| Volts
+5 VDC| 5.70| 6.3| 7.0| Volts
+3.3 VDC| 3.70| 4.2| 4.8| Volts -
Short circuit
An output short circuit is defined as any output impedance less than 0.1 ohms. The power supply shall shut down and latch off for shorting the +3.3 VDC,+5 VDCor+12 VDC rails. Shorts between main output rails and +5VSB shall not cause any damage to the power supply. The power supply shall either shut down and latch off or fold back for shorting the negative rails.+5VSB must be capable of being shorted indefinitely, but when the short is removed, the power supply shall recover automatically or by cycling PS_ON#. The power supply shall be capable of withstanding a continuous short-circuit to the output without damage or overstress to the unit. -
Over-power protection
The power supply will be shut down and latch off when the output power is 110%~150%
Dimensions: 150mm x 86mm x 158mm (5.9″ x 3.4″ x 6.2″) W x L x H
Description of Connectors
Precautions
Warning! To avoid the risk of electrical shock, unauthorized persons need the following precautions:
- Do not open the power supply case!
- Before turning on, please make sure that the input voltage of the red RMS side switch on the power supply corresponds to the power voltage given in your environment. (USA & Canada: 115V; Europe, Central and South America: 230V).
- Avoid exposure to humidity.
Information
Thank you for purchasing a high-quality Apevia product! Please visit our website at http://www.apevia.com for complete warranty information and future support for your product. For the latest release information, or should you have any questions, please visit our website, or contact us at:
- Support Phone Number: 1-909-718-0789
- Support E-mail: support@apevia.com
Installation
- Plug the 24-pin connector onto the motherboard.
- 4-pin or 8-pin (4+4pin) + 12V connector used for CPU only.
- PCI Express connector for video card only.
- 4-pin Molex connectors used for hard drive, CD-ROM, and cooling fans.
- 4-pin floppy connector used for floppy disk or zip drives.
- SATA connectors are used for SATA hard drives.
Troubleshooting
If the power supply fails to operate properly, please check the following before requesting an RMA:
- Please make sure the power supply and power cord is connected properly.
- Please make sure the power cord is plugged into the power socket.
- Please make sure the power supply 1/0 button is switched to the ” !” position.
- Please check if all the connectors (motherboard, floppy, and peripherals) are connected properly.
Please allow 5 seconds interval before turning the power on again when the power supply is switched off manually (setting the 1/0 switch to the ” O” position)
PRESTIGE Power Supply
- 600W Prestige Power
- 800W Prestige Power
- 1000W Prestige Power
FREQUENTLY ASKED QUESTIONS
What is the model number of the Apevia Power Supply?
The model number of the Apevia Power Supply is ATX-RP800W.
What is the output wattage of the Apevia ATX-RP800W Power Supply?
The output wattage of the Apevia ATX-RP800W Power Supply is 800 watts.
What cooling method does the Apevia ATX-RP800W Power Supply use?
The Apevia ATX-RP800W Power Supply uses air cooling.
What are the dimensions of the Apevia ATX-RP800W Power Supply?
The dimensions of the Apevia ATX-RP800W Power Supply are 6.2 x 5.9 x 3.4 inches.
How much does the Apevia ATX-RP800W Power Supply weigh?
The Apevia ATX-RP800W Power Supply weighs 4.7 pounds.
What is the price of the Apevia ATX-RP800W Power Supply?
The price of the Apevia ATX-RP800W Power Supply is $66.99.
What connector types are supported by the Apevia ATX-RP800W Power Supply?
The Apevia ATX-RP800W Power Supply supports ATX, PCI-E, and SATA connector types.
What form factor does the Apevia ATX-RP800W Power Supply have?
The Apevia ATX-RP800W Power Supply has an ATX form factor.
What is the maximum input voltage for the Apevia ATX-RP800W Power Supply?
The maximum input voltage for the Apevia ATX-RP800W Power Supply is 230 volts.
What is the minimum input voltage for the Apevia ATX-RP800W Power Supply?
The minimum input voltage for the Apevia ATX-RP800W Power Supply is 110 volts.
What system bus connectors are available on the Apevia ATX-RP800W Power Supply?
The Apevia ATX-RP800W Power Supply has 6-pin and 8-pin system bus connectors.
How many fans are included with the Apevia ATX-RP800W Power Supply?
The Apevia ATX-RP800W Power Supply includes 1 fan.
What is the cooling method used by the Apevia ATX-RP800W Power Supply?
The cooling method used by the Apevia ATX-RP800W Power Supply is air cooling.
What type of devices is the Apevia ATX-RP800W Power Supply compatible with?
The Apevia ATX-RP800W Power Supply is compatible with personal computers.
What are the benefits of the 800-watt output of the Apevia ATX-RP800W Power Supply?
The 800-watt output of the Apevia ATX-RP800W Power Supply provides ample power for high-performance components and ensures stable operation.
DOWNLOAD THE PDF LINK:Apevia ATX-PR800W Prestige Power Supply User’s Manual
REFERENCE:Apevia ATX-PR800W Prestige Power Supply User’s Manual- Device.Report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>