ET2 E21180 LED Wall Sconce Highball Instruction Manual

August 8, 2024
ET2

ET2 E21180 LED Wall Sconce Highball

Specifications

  • Item/Model Number: E21180 Highball LED Wall Sconce
  • 1 x LED 10W (Included)

Product Usage Instructions

Assembly

  1. Read the instructions carefully before assembling the product.
  2. Open the package with care to avoid damaging components.
  3. Remove all packaging materials and keep them for future use.
  4. Choose a clean, level assembly area away from hard surfaces.
  5. Ensure you have all necessary contents for assembly.

Installation

  • Assemble the product close to the installation location.
  • Do not overtighten screws and bolts to prevent damage.
  • Disconnect from the power source before assembling or cleaning.
  • Switch off, unplug, and allow the bulb to cool before replacing or cleaning.

Maintenance

  • Check product cord for any damage before use.
  • Clean with a mild detergent and cloth, avoiding harsh cleaners.
  • Use appropriate cleansers for specific shade surfaces.

Safety

  • Keep hardware parts and packaging away from children.
  • Avoid letting children play with the product.
  • Do not connect wires directly to live wires to prevent short circuits.
  • Avoid prolonged exposure to heat sources to prevent damage.

Before Getting Started

  1. Read the instruc ons carefully prior to assembling the product.
  2. When you open the package with a sharp tool like a box knife, be careful not to damage the components inside.
  3. Carefully remove all packaging materials and retain for future use.
  4. Keep all hardware parts and packaging out of reach of small children.
  5. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the product.
  6. Ensure that you have all required contents for complete assembly.
  7. Take care when lifting Assemble the product in close proximity to where you intend to install it.
  8. Do not over the tighten screws and bolts as this may damage the threads.
  9. Do not let children play with this product.

Risk of Suffocation : Keep packaging materials away from children.

Lamp Care Instructions

  1. Carefully read through the instruction sheet before assembly and using the product.
    Caution there is a risk of shock!

  2. Disconnect from power source before assembling or cleaning.

  3. Switch off, unplug and allow bulb to cool before replacing bulb or cleaning.

  4. Only use the recommended bulb type and do not exceed the maximum wattage as it could cause fire

  5. Check the product cord to be sure is free torn or frayed.
    WARNING : Wires must to be connected to low voltage driver and should not be connected directly to live wire or a short may occur.

Cleaning & Maintenance

  1. On polished finishes, often using talc powder can reduce the appearance of fingerprints and other smudges.
  2. For respective shade surfaces, use the appropriate cleansers, i.e. glass cleaner, stone polish, & wood polish.
  3. Clean with soft cloth and a mild detergent. Do not use abrasive or harsh cleaners.
  4. Periodically (every 90-180 days) make sure that the screws are fully tightened.
  5. Prolonged exposure to heat sources may cause glazing, melting and scorching, or even cause color to fade.

PARTS

Before getting,started, ensure the package contains the following components:

This fixture is equipped with an LED driver, please refer to the Wiring Diagram for more details

Installation

WIRING DIAGRAM

DIMMER COMPATIBILITY

MUST be installed by an experienced professional CRITICAL KNOWLEDGE of electronic lighting systems required

IMPROPER WIRING and/or INCORRECT DIMMER use can cause CATASTROPHIC DAMAGE! THIS FIXTURE MUST BE INSTALLED with a COMPATIBLE DIMMER SWITCH DO NOT CUT FACTORY-MADE CONNECTIONS.

AC:120-277V~50/60HZ

LED DRIVER DIAGRAM

SCHEMATIC FOR GENERAL REFERENCE ONLY

VERIFIED LIST OF TESTED DIMMERS

  • Lutron Diva DVCL-153P
  • Lutron Diva DVELV-300P
  • Lutron Diva Caseta PD-6WCL
  • Lutron Maestro MACL-153M
  • DEAKO-Smart Dimmer
  • DEAKO-Single Dimmer
  • LEVITON 6672-L
  • LEVITON DSL06

GENERAL COMPATIBILITY
TRIAC / FORWARD PHASE
ELV / REVERSE PHASE
Only at 120VAC
Due to inrush current, wattage should not exceeed 150W on a 600W dimmer

IMPORTANT!
If the control is not paired properly to LED fixtures, irreparable damage may occur. If the dimmer you are using is not listed here, consult a lighting professional or view our Dimming Compatibility Chart online: www.et2online.com/led-dimmer

MUST be installed by an experienced professional CRITICAL KNOWLEDGE of electronic lighting systems required © 2024 ET2 CONTEMPORARY LIGHTING

FAQ

Q: How often should I check the screws?
A: It is recommended to check the screws every 90-180 days to ensure they are fully tightened.

Q: What type of bulb should I use?
A: Only use the specified bulb type and make sure it is compatible with the fixture.

Q: How should I clean the product?
A: Clean with a mild detergent and cloth, avoiding abrasive cleaners. Use appropriate cleansers for different surfaces.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ET2 User Manuals

Related Manuals