luminii 0-10V Athena LED Driver 96 Watt Instruction Manual
- June 1, 2024
- luminii
Table of Contents
luminii 0-10V Athena LED Driver 96 Watt
Specifications
- Input: 120 – 277 V AC, 1.1 A, 50/60 Hz
- Output: 24 V DC, 4.0 A
- Max. Wattage: 96 W
Product Usage Instructions
1. Pre-Installation Checks:
Before installing, ensure the LED Driver has the correct input voltage, output voltage, and wattage as specified for the job. Check wire markings to match the wiring diagram provided.
2. Mounting the LED Driver:
1. The LED Driver can be mounted vertically or horizontally with a minimum of
3 inches clearance around it to ensure proper air circulation.
2. Make sure the Lutron Athena Wireless node has at least 1 inch clearance
from any metal surfaces like conduit.
3. Connecting Power:
1. Connect the 120-277V AC power into the housing from the electrical panel.
2. Connect the 24V DC low voltage conduit for the LED. No additional control
wire connections are needed as the power supply is already connected to the
Athena wireless node.
4. Finalizing Installation:
1. Insert the wire nut connections in the driver housing.
2. Close the housing cover and secure it using the eight screws provided.
FAQ
- Q: Can the LED Driver be installed in wet locations?
- A: No, the LED Driver is only suitable for dry locations and must not be installed where it may come into contact with water.
- Q: Can I adjust the output voltage of the LED Driver?
- A: No, the LED Driver provides a fixed output voltage of 24V DC.
- Q: Is it safe to install the LED Driver without the help of a qualified electrician?
- A: No, due to the hardwired nature of the LED Driver and electrical safety considerations, it should only be installed by a qualified electrician.
Please read all instructions prior to installation and keep for future reference!
This LED Driver is to be installed in accordance with Article 450 of the National Electrical Code. The LED Driver must be installed in a well- ventilated area and free from explosive gases and vapours. Proper operation requires the free flow of air as this LED Driver is hardwired, it should only be installed by a qualified electrician. Suitable For Dry Locations.
Dimension
Installation Instruction
- 1.1 LED Driver can be mounted vertically or horizontally. With a minimum of 3″ clearance around LED Driver to provide proper air circulation.
- 1.2 Ensure that the Lutron Athena Wireless node has at least 1″ clearance from any metal such as conduit.
- 2.1 Remove the cover from top of the driver housing to expose the driver wires. Screws for cover will be found inside the housing.
- 3.1 Connect the 120-277V AC power into the housing from the electrical panel, followed by connecting the 24V DC low voltage conduit for the LED. There is no control wire connections to make since the power supply is already connected to the Athena wireless node.
Factory Resetting the Lutron Athena Wireless Node using the Lutron App
Factory Resetting Lutron Node: If a node isn’t working or you aren’t able to add it to a new project, this is a troubleshooting guide to factory reset the Athena wireless node
- Step 1: Open the Lutron App
- Step 2: Make Sure your device is connected to the same WiFi as the Lutron Athena nodes
- Step 3: Select Professional
- Step 4: Sign into your myLutron Account
- Step 5: Click ‘Next’ to pass through Account screen
- Step 6: Select ‘Access an Existing System
- Step 7: Select ‘More options’
- Step 8: Click ‘Reset Device’
- Step 9: Select ‘Continue using app’
- Step 10: Follow the next directions on the app to successfully reset the Athena Wireless node To confirm the Athena node has been reset, power cycle the load connected to that Athena wireless node. The load will either dim to off or cycle through CCT’s and then turn to full brightness
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Contact
- 7777 Merrimac Ave
- Niles, IL 60714
- T 224.333.6033
- F 224.757.7557
- info@luminii.com
- www.luminii.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>