Luminii 0-10V Warm Dim 96 Watt LED Driver Installation Guide
- June 1, 2024
- luminii
Table of Contents
Luminii 0-10V Warm Dim 96 Watt LED Driver
Specifications
- Input: 120 – 277 V AC, 1.1 A, 50/60 Hz
- Output: 24 V DC, 4.0 A
- Max. Wattage: 96 W
Product Usage Instructions
1. Pre-Installation Checks:
- Before installing, verify that the LED Driver has the correct input voltage, output voltage, and wattage as labeled.
- Check wire markings to ensure they match the provided wiring diagram and maximum load specifications.
2. Mounting and Placement:
- LED Driver can be mounted vertically or horizontally with a minimum clearance of 3 inches for proper air circulation.
- Ensure the Lutron Athena Wireless node has at least a 1-inch clearance from any metal surfaces like conduit.
3. Installation Steps:
- Remove the cover from the top of the driver housing to access the driver wires.
- Connect the 120-277V AC power from the electrical panel followed by connecting the 24V DC low voltage conduit for the LED.
- No additional control wire connections are needed if the power supply is already connected to the Athena wireless node.
4. Final Steps:
- Insert wire nut connections in the driver housing.
- Close the housing cover and securely fasten it using the eight screws provided.
FAQ
- Q: Can this LED driver be used in damp or wet locations?
- A: No, this LED driver is suitable for dry locations only.
- Q: What is the recommended clearance around the LED Driver for proper air circulation?
- A: A minimum clearance of 3 inches is recommended around the LED Driver for adequate air circulation.
- Q: Is it necessary to hire a qualified electrician for installation?
- A: Yes, as this LED driver is hardwired, it should only be installed by a qualified electrician for safety and proper functioning.
Please read all instructions prior to installation and keep for future reference!
THIS LED DRIVER IS TO BE INSTALLED IN ACCORDANCE WITH ARTICLE 450 OF THE NATIONAL ELECTRICAL CODE. THE LED DRIVER MUST BE INSTALLED IN A WELL- VENTILATED AREA AND FREE FROM EXPLOSIVE GASES AND VAPORS. PROPER OPERATION REQUIRES THE FREE FLOW OF AIR. AS THIS LED DRIVER IS HARDWIRED, IT SHOULD ONLY BE INSTALLED BY A QUALIFIED ELECTRICIAN. SUITABLE FOR DRY LOCATION.
Dimension
Installation Instruction
- 1.1 LED Driver can be mounted vertically or horizontally. With a minimum of 3″ clearance around LED Driver to provide proper air circulation.
- 1.2 Ensure that the Lutron Athena Wireless node has at least 1″ clearance from any metal such as conduit.
- 2.1 Remove the cover from top of the driver housing to expose the driver wires. Screws for cover will be found inside the housing.
- 3.1 Connect the 120-277V AC power into the housing from the electrical panel, followed by connecting the 24V DC low voltage conduit for the LED. There is no control wire connections to make since the power supply is already connected to the Athena wireless node.
Please read all instructions prior to installation and keep for future reference!
THIS LED DRIVER IS TO BE INSTALLED IN ACCORDANCE WITH ARTICLE 450 OF THE NATIONAL ELECTRICAL CODE. THE LED DRIVER MUST BE INSTALLED IN A WELL VENTILATED AREA AND FREE FROM EXPLOSIVE GASES AND VAPORS. PROPER OPERATION REQUIRES THE FREE FLOW OF AIR. AS THIS LED DRIVER IS HARDWIRED, IT SHOULD ONLY BE INSTALLED BY A QUALIFIED ELECTRICIAN. SUITABLE FOR DRY LOCATION.
User Guide Instructions
2.1 Open the App and choose one of the factory pre-build presets.
- VintageDim® Warm Dim
Using the App
Place phone directly on the VintageDim® module. Phone i may when you frog a
single beging. see ming “Programming Successful” screen. If the driver was off
during programming, simply power on and the driver will work according to the
new program. If the driver was on during programming, it will need to be power
cycled for new programming to become active.
- 4.2 Place phone directly on the VintageDim® module. Reading is complete when you see the following confirmation on screen.
- 4.3 After successful reading you will see new user preset created with corresponding name and description.
Contact
- 7777 Merrimac Ave
- Niles, IL 60714
- T 224.333.6033
- F 224.757.7557
- info@luminii.com
- www.luminii.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>