KSP 82303 Torsion Bar Key Forged Torsion Bar Keys Lift Kit Installation Guide

KSP 82303 Torsion Bar Key Forged Torsion Bar Keys Lift Kit

Product Information

Specifications:

• Kit No.: 82303
• Product Name: Torsion Key Leveling Key Kit
• Vehicle Application: Chevy, GMC (Refer to vehicle list in the manual)

Product Usage Instructions

1. Block the rear tyres of the vehicle and place a jack stand on both sides.
2. Remove the front tyre and wheel assembly.
3. Remove the lower shock bracket and shock from the factory.
4. Install the Extender shock bracket to the lower control arm.
5. Install the lower shock and hardware to the new mount and torque to spec.
6. Repeat the lower shock bracket installation on the other side.
7. Locate the torsion bar cross member and measure or mark the adjuster bolt length for reference.
8. Remove adjuster bolts from the torsion key using the unloading tool.
9. Install the new torsion key, and reinstall bar pin and torsion bolt with proper orientation.
10. Torque all bolts to factory specs.
11. Have an alignment professional check and adjust the alignment to factory specifications.
12. Re-torque lug nuts after 25 miles of driving and all hardware after 500 miles.

FAQ:

• Q: Do I need to perform a front-end alignment after installing this kit?
  A: Yes, it is recommended to have a front-end alignment immediately after installing this kit to ensure proper vehicle handling and tire wear.

• Q: How can I contact the seller for support or inquiries?
  A: You can contact the seller via email at E-mailspeed@nbgoldenlion.com or through Amazon and eBay platforms using the provided instructions in the manual.

(if you want to buy a shock bracket, please contact us )

Vehicle application

Chevy:

• Avalanche 2500 02-06 2WD 4WD 8-Lug
• Silverado 1500HD 01-07 2/4WD 8Lug (unfit 03 year)
• Silverado 2500 99-04 2WD 4WD 8-Lug
• Silverado 2500HD 01-10 2WD 4WD 8-Lug
• Silverado 3500 01-07 2WD 4WD 8-Lug
• Silverado 3500HD 07-10 2WD 4WD 8-Lug
• Suburban 2500 00-13 2WD 4WD 8-Lug (Except 2000 Suburban 2500 4 wheel drive 8 lug)

GMC:

• Yukon XL 2500 00-13 2WD 4WD 8-Lug
• Sierra 1500HD 01-07 2WD 4WD 8-Lug
• Sierra 2500 99-04 2WD 4WD 8-Lug
• Sierra 2500HD 01-10 2/4WD 8Lug (unfit 02, 06 year)
• Sierra 3500 01-07 2WD 4WD 8-Lug
• Sierra 3500HD 07-10 2WD 4WD 8-Lug

1. To begin the installation, block the rear tires of the vehicle. Place a jack stand on both the driver and passenger side.

2. Remove the front tire and wheel assembly.

3. Remove the lower shock bracket and remove the shock from the factory. Remove the factory lower shock bracket and discard.

4. Install the Extender shock bracket to the lower control arm with the angle on the bracket going toward the centre of the vehicle. (If you don’t have an extender shock bracket, you need to buy it.)

5. Install the lower shock and shock hardware to the new mount and torque to spec.

6. Repeat the lower shock bracket installation to the other side of the vehicle.

7. Locate the torsion bar cross member. There is a bolt on each side of the cross member that adjusts the torsion bar preload. Measure or mark the exposed length of the adjuster bolt for reference during re-assembly.

8. Working on the driver side, Remove the adjuster bolts from the torsion key.
   Using the torsion key unload tool carefully unload the torsion key and remove the keeper. Note the  orientation of the torsion bar key about the end of the torsion bar

9. Install the new torsion key, and reinstall the bar pin and torsion bolt.
   Using the same precautions and procedures that were used during the removal

10. Torque all bolts in the installation torsion key to factory specs.

11. You have an alignment professional check and adjust the alignment to factory specifications.

12. After 25 miles of driving re-torque the lug nuts, and after 500 miles of driving re-torque all of the hardware associated with the levelling spacer installation to factory specifications. Repeat the torquing procedure as required.
    The Vehicle Needs To Have A Front End Alignment Performed Immediately After The Installation Of This Kit.

Thank you for the purchases!
It is our honour to help you. So please write to us about what you think and what you need. We will reply to you ASAP and try our overwhelming best to help you solve the problem. Please feel free to contact us via eBay message or Amazon tools.
E-mail：speed@nbgoldenlion.com

Amazon:

1. Visit www.amazon.com/your-orders
2. Find your product
3. Click on “Contact Seller”
4. Include your order #

eBay:

1. Visit www.ebay.com
2. Click on ”My eBay”
3. Find your product
4. Click on “More actions”
5. Click on “Contact seller”

References

• Amazon Sign-In

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>