KSP 2-4 Front Shock Extenders Installation Guide
- June 1, 2024
- KSP
Table of Contents
KSP 2-4 Front Shock Extenders
INSTALLATION INSTRUCTION
| Kit Contents: | Quantity: |
|---|---|
| SHOCK EXTENSION (L/R) | 2 PCS. |
| M12x1.75-65MM Bolts | 2 PCS. |
| M12x1.75 Nylon Insert Lock Nuts | 2 PCS. |
| M12 Washers | 4 PCS. |
| M10x1.5-20MM Bolts | 2 PCS. |
| M10x1.5 Nylon Insert Lock Nuts | 2 PCS. |
| M10 Washers | 2 PCS. |
- Confirm that all the hardware in the parts list is in the kit.
- Do not begin this installation if any part is missing.
- Read the instructions thoroughly before beginning this installation.
- Note: Shock absorber extensions are designed to be used with factory shocks on the vehicle with a 2-4″ front lift to reduce the over-extended pistons so that your factory shocks can be reused without compromising ride quality.
- Warning: DO NOT drive the vehicle until all work has been completed and checked.
- Raise the vehicle and remove the wheels. Always ensure proper safety procedure is followed when working underneath your car, including the use of using jack stands or other equipment.
- Remove the front shock absorber from the vehicle. Keep the factory hardware for use during reassembly.
- Place shock extension over shock mount facing towards within of vehicle as shown. Insert spacer tube into factory shock mount. Insert the spacer tube and one M12 washer into the shock extension.
- Insert the factory bolts with the washer, from outside, through the hole in the factory shock mount, shock extension, spacer tube,M12 washer, and out the other side. Secure with washer a factory nuts.
- Re-mount the bottom of the shock into the new shock extension.
- Repeat steps 2-5 on the opposite side of the vehicle.
In the end, check all hardware is mounted at correct torque settings. Recheck all work. Re-tighten Shock Extension mounting bolts. Test drive, then have a trained technician perform an alignment.
Thank you for your purchases!
It is our honor to help you. So please write us about what you think and what
you need. We will reply you ASAP and try our overwhelming best to help you
solve the problem. Please feel free to contact us via eBay messages or Amazon
tools.
Amazon
- Visit www.amazon.com/your-orders
- Find your product
- Click on “contact seller”
- Include your order #
eBay
- Visit www.ebay.com
- Click on “My eBay”
- Find your product
- Click on “More actions”
- Click on “Contact Seller”
Specifications
- Model: 9F723P2
- Kit Contents:
- SHOCK EXTENSION (L/R)
- M12x1.75-65MM Bolts – 2 PCS.
- M12x1.75 Nylon Insert Lock Nuts – 2 PCS.
- M12 Washers – 2 PCS.
- M10x1.5-20MM Bolts – 4 PCS.
- M10x1.5 Nylon Insert Lock Nuts – 2 PCS.
- M10 Washers – 2 PCS.
Final Steps
- Check that all hardware is mounted at the correct torque settings.
- Recheck all work and re-tighten the Shock Extension mounting bolts.
- Test drive the vehicle and then have a trained technician perform an alignment.
FAQ
Q: Can these shock extensions be used with any vehicle?
A: The shock extensions are designed to be used with factory shocks on
vehicles with 2-4 inches of front lift to reduce over-extension of pistons.
Ensure compatibility before installation.
Q: How do I contact the seller for assistance?
A: You can contact us via eBay messages or Amazon tools. For Amazon, visit
www.amazon.com/your-orders, find your
product, click on contact seller, and include your order #. For eBay, visit
www.ebay.com, click on My eBay, find your product,
click on More Actions, and then click on Contact Seller.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>