BEGA 85138K3 Performance Floodlight User Guide

: June 1, 2024
: BEGA

Table of Contents

BEGA 85138K3 Performance Floodlight
Performance floodlight
Instructions for use
Installation
Cleaning · Maintenance
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 85138K3 Performance Floodlight

Performance floodlight

BEGA-85138K3-Performance-Floodlight-fig-1

Instructions for use

Application

Performance floodlight with mounting box.
For a variety of interior and exterior lighting applications.

Product Description

Luminaire made of aluminium alloy, aluminium and stainless steel
BEGA Unidure coating technology
Colour graphite or silver
Clear safety glass
Silicone gasket
The reflector surface is made of pure aluminium
BEGA Hybrid Optics
The rotation range of floodlight is 350°
Swivel range -25°/+90°
Mounting box with 2 fixing holes ø 4.8mm · 67mm spacing
2 cable entries for through-wiring of mains
supply cable ø 7-10.5mm, max. 5G1.5
Connecting terminal 2.5
with plug connection
Earth conductor connection
BEGA Ultimate Driver
Complies with flicker requirements per IEEE 1789,
DIN IEC/TR 63158, DIN IEC/TR 61547-1
LED power supply unit 220-240 V x 0/50-60 Hz DC 176-264 V
DALI-controllable
Number of DALI addresses: 1
Basic insulation is provided between the mains and control cables

BEGA Thermal Control

Temporary thermal regulation to protect temperature-sensitive components without switching off the luminaire
Safety class I
Protection class IP 65
Dust-tight and protection against water jets
Impact strength IK06
Protection against mechanical impacts < 1 joule
Conformity mark
Wind catching area: 0.023 m²
This product contains light sources of energy efficiency class(es) E

Lighting technology

Symmetrical wide beam light distribution
Half beam angle 45°
For special lighting applications, an optical filter can be used to change the symmetrical

Lamp

Module connected wattage 24.1 W
Luminaire connected wattage 26.8 W
Rated temperature ta=25 °C
Ambient temperature ta max=40 °C

85 138K3

Module designation LED-0800/930
Colour temperature 3000 K
Colour rendering index CRI >90
Module luminous flux 3350 lm
Luminaire luminous flux 2472 lm
Luminaire luminous efficiency 92,2 lm/W

85 138K4

Module designation LED-0800/940
Colour temperature 4000 K
Colour rendering index CRI >90
Module luminous flux 3400 lm
Luminaire luminous flux 2509 lm
Luminaire luminous efficiency 93,6 lm/W

Safety

The installation and operation of this luminaire are subject to national safety regulations.
Installation and commissioning may only be carried out by a qualified electrician.
The manufacturer accepts no liability for damage caused by improper use or installation.
If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

Overvoltage protection

The electronic components installed in the luminaire are protected against overvoltage by DIN EN 61547.
To achieve additional protection against e.g. transients, etc. we recommend separate overvoltage protection components.
You can find them on our website at www.bega.com.
The ideal protection of all electronic components installed in the luminaires is achieved by using bounce-free switching contacts such as an electronic relay (solid-state relay), e.g. BEGA 71320.

Installation

LEDs are high-quality electronic components!
Please avoid touching the light output opening of the LED directly during installation or relamping.
Undo the hexagon socket head screw (wrench size 3mm) up to the stop and disassemble the mounting plate.
Pass the power connecting cable through the cable entry in the mounting plate.
Note the position of application of the mounting plate “arrow down”.
Fix the mounting plate with enclosed or any other suitable fixing material onto the mounting surface.
Be sure to use the gasket rings supplied.
Make an earth conductor connection.
Push silicone sleeves over the lines and make an electrical connection to the terminal (plug connection).
For digital control please use the 2-pole plug connector DA, DA.
In case this connector is not used the luminaire will be operated at full light output.
Push the plug into the coupler as far as it will go.
Connect the floodlight unit’s green and yellow protective earth conductor to the terminal marked 1 in the mounting plate.
Make sure that the gasket is positioned correctly.

Place the floodlight unit onto the mounting plate as displayed in the sketch, and align and screw together firmly.

Adjustment of beam direction

Undo the joint screw (hexagon socket head wrench size 5 mm) and set the desired beam direction.
Tighten the joint screw.
Torque = 7Nm.

Cleaning · Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high-pressure cleaners.

Maintenance
The connecting cable between the mounting box and floodlight has to be inspected for obvious damages and has to be replaced by a qualified electrician only.

Please note
Do not remove the desiccant bag from the luminaire housing. It is needed to remove residual moisture.

Replacing the LED module
The designation of the LED module is noted on a separate label in the luminaire or on the underside of the specific LED module. The light colour and light output of BEGA replacement modules correspond to those of the modules originally fitted. The module can be replaced by qualified persons using standard tools. Disconnect the system.

Open the floodlight
Undo the locking pin (hexagon socket head wrench size 2.5 mm) on the back side of the floodlight housing. Remove the trim ring along with the safety glass and reflector by twisting it counterclockwise. Replace the LED module. Please follow the installation instructions for the LED module. Inspect and, if necessary, replace the luminaire gaskets.

The defective glass must be replaced. Place the trim ring with glass and reflector on the floodlight housing in such a way that the notches in the trim ring and floodlight housing align on top of each other. Twist on the trim ring clockwise as far as the stop. Tighten the locking pin.