EVENT LIGHTING EL1000RGB 1000 mW RGB Mini Animation Laser User Manual

: June 13, 2024
: EVENT LIGHTING

Table of Contents

EVENT LIGHTING EL1000RGB 1000 mW RGB Mini Animation Laser
Product Information
Instructions
Safety Instructions
Product Installation
Menu
DMX Chart
Technical Specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

EVENT LIGHTING EL1000RGB 1000 mW RGB Mini Animation Laser

Product Information

Product Name: EL1000RGB
Product Type: Mini Animation Laser
Power Output: 1000 mW
Color Output: RGB (Red, Green, Blue)
Manufacturer: Event Lighting
Version: 1.0
Website: www.event-lighting.com.au

Instructions

For your safety, please read this user manual carefully before use.

Event Lighting reserves the right to revise the manual at any time. Information and specifications within this manual are subject to change without notice. Event Lighting assumes no liability or responsibility for any errors or omissions. Please consult Event Lighting for any clarification or information regarding this item.

Safety Instructions

Warning

Do not open this fixture, there are no user serviceable parts inside. Risk of electric shock.
Do not look directly at the light source.
Avoid contact with the unit during operation, as the housing may become hot. Allow the fixture to cool for at least 15 minutes after turning off before touching.
Install this fixture in a location with adequate ventilation, at least 50cm from adjacent surfaces.
Do not operate this fixture, or connect this device to power, within 50cm of any flammable material.
Use a safety chain when mounting this fixture overhead.
Do not operate this fixture outdoors where excessive dust, heat, water or humidity may affect it.
Do not operate this fixture if the housing, lenses, or cables appear damaged.
Do not connect this fixture to a dimmer or rheostat.
Do not operate this fixture at temperatures higher than 40°C (104°F).
Only connect this fixture to a grounded and protected circuit.
Only use the hanging bracket to carry this fixture.
Stop using this fixture immediately if a serious operating problem becomes apparent.

Laser Warning

Laser light can cause instant eye injury if the product is not set up and used correctly. Avoid direct eye contact with the laser light. Never intentionally expose your eyes or others to direct laser light. This laser product can potentially cause instant eye damage or blindness if laser light directly strikes the eyes. The heat from a laser cannot be felt, but it can still injure or cause blindness. This can occur even with very small amounts of exposure at a long distance.

This product contains a Class 3B Laser. It is critical to prevent the possibility of ANY direct eye exposure.

Do not operate the laser without reading and understanding the safety information contained in this manual.
Test the product before public use to ensure the lasers are functioning correctly, and that eye exposure is impossible.
Do not assume exposure to an individual laser beam is safe.
Do not assume a moving laser light is safe. Eye injury can occur instantly.
EL1000RGB must be installed at least 3 metres above ground level and 3 metres from any person. See the Product Installation section for details.
Do not point the laser at any person or animal.
Do not point the laser towards any area where people could be exposed to them.
Do not point the laser towards any reflective surfaces, such as windows, mirrors and shiny metals. Laser reflections can also cause injury.
Do not point the laser towards any area where you or the operator do not know where the beams are being directed.
Do not point the laser into the sky or towards any aircraft.
The legal requirements for operating laser products vary between jurisdictions. It is the user’s responsibility to meet the legal requirements in the location/country of use.

Product Installation

EL1000RGB can be mounted in many orientations, provided each individual device is secured by the use of the correct mounting bracket.
This device should be directed above the heads of people. Do not direct this device towards the line of sight of anyone. Refer to the diagram below.
A minimum of 3 meters vertical separation is required between the floor and the laser device.
A minimum of 3 metres horizontal separation is required between the laser light and any person or public space.
Use a safety chain when mounting EL1000RGB overhead.

Menu

| Values|

Function

---|---|---
Addr| 1-512| Set DMX address
AUTO| 0-9| Auto mode 0-9
SOUN| 0-9| Sound active mode 0-9
VERSION| Ver1.1| Software version

DMX Chart

Channel

| Function| Min DMX| Max DMX|

Description

---|---|---|---|---
1| Laser on/off| 0| 9| Laser off
10| 255| Laser on
2| Colour control| 0| 69| Static colours, white-red-blue-pink-cyan-yellow- green
70| 79| Colour change (speed controlled by Ch. 3)
80| 89| Default colour (speed controlled by Ch. 3)
90| 99| Rainbow colour (speed controlled by Ch. 3)
100| 224| Segment colour, 5 data stepping (speed controlled by Ch. 3)
225| 229| Dynamic colour 1 (speed controlled by Ch. 3)
230| 234| Dynamic colour 2 (speed controlled by Ch. 3)
235| 239| Dynamic colour 3 (speed controlled by Ch. 3)
240| 244| Dynamic colour 4 (speed controlled by Ch. 3)
245| 249| Dynamic colour 5 (speed controlled by Ch. 3)
250| 255| Dynamic colour 6 (speed controlled by Ch. 3)
3| Colour speed| 0| 9| No function
10| 127| Clockwise, slow to fast
128| 255| Anticlockwise, slow to fast
4| Pattern option| 0| 255| Pattern option
5| Patterns group optoin| 0| 50| Inner patterns group 1
51| 101| Inner patterns group 2
102| 152| Inner patterns group 3
153| 203| Inner patterns group 4
204| 255| Inner patterns group 5
6| Pattern size| 0| 255| Manual pattern size option
7| Pattern auto zoom| 0| 15| Manual zoom
16| 55| Zoom, small to large, speed slow to fast
56| 95| Zoom, large to small, speed slow to fast
96| 135| Cycle zoom large to small, speed slow to fast
| | 136| 175| Cycle zoom 1, speed slow to fast
---|---|---|---|---
176| 215| Cycle zoom 2, speed slow to fast
216| 255| Cycle zoom 3, speed slow to fast
8| Centre rotation| 0| 127| Rotation angle
128| 191| Clockwise rotation speed
192| 255| Anticlockwise rotation speed
9| Horizontal rotation| 0| 127| Flip horizontal location
128| 255| Flip horizontal speed
10| Vertical rotation| 0| 127| Flip vertical location
128| 255| Flip vertical speed
11| Horizontal remove| 0| 127| Horizontal location
128| 255| Horizontal auto location, speed slow to fast
12| Verical remove| 0| 127| Vertical rotation
128| 255| Vertical auto location, speed slow to fast
13| Wave| 0| 9| No function
10| 255| Wave range and speed (range small to large, speed slow to fast)
14| Patterns drawing| 0| 1| No function
2| 63| Drawing by manual adjustment 1
64| 127| Drawing by manual adjustment 2
128| 153| Automatic drawing (increasing)
154| 179| Automatic drawing (decreasing)
180| 205| Automatic drawing (increasing to decreasing, reverse)
206| 255| Automatic drawing (increasing to decreasing)
15| Inner dynamic effect| 0| 2| No function
3| 229| Single group dynamic effect, speed and colour controlled by Ch. 16
230| 249| Random auto effect, speed and colour controlled by Ch. 16
16| Inner dynamic effect speed| 0| 127| Inner effect speed, fast to slow, colour determined by inner program
128| 255| Inner effect speed, fast to slow, colour determined by DMX