BEGA 84760 Bollard Tube with PIR and Light Sensor Instruction Manual

: June 1, 2024
: BEGA

Table of Contents

BEGA 84760 Bollard Tube with PIR and Light Sensor
Product Information
Product Usage Instructions
FAQ
Dimension
Instructions for use
Product Description
Installation
Circuit variants
Commissioning
Operating modes
Reset to factory settings
Cleaning Maintenance
Accessories
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BEGA 84760 Bollard Tube with PIR and Light Sensor

BEGA-84760-Bollard-Tube-with-PIR-and-Light-Sensor-
product

Product Information

Specifications:

Product Name: Mounting Plate Luminaire
Model Number: 84 760
Manufacturer: BEGA Gantenbrink-Leuchten KG
Compliance: Directive 2014/53/EU (RED)

Product Usage Instructions

Safety:

The installation and operation of this luminaire must comply with national safety regulations. Only a qualified electrician should carry out the installation and commissioning to prevent any damage due to improper use or installation. Any modifications made to the luminaire should be done by authorized personnel.

Installation:

Open the connection box and lead the mains supply cable into it.
Connect the phase wire to the marked L1, the neutral wire to the N marked, and the earth conductor to the PE marked connecting terminal.

Circuit Configuration:

The luminaire can be configured and controlled individually. It is possible to forward the switching signal to additional luminaires via the relay contact L’. Refer to the circuit diagrams for proper configuration.

Commissioning:

Connect the power supply to commission the luminaire. The brightness sensor may take up to 10 minutes to calibrate after activation. The factory settings include Mode: PIR and light, PIR sensitivity: 100%, Shut-down delay: 5 minutes, and Brightness threshold: 32.

Control:

The luminaire can be controlled for on/off functionality.

FAQ

Q: Can the luminaire settings be adjusted via smartphone?
- A: Yes, the integrated PIR motion and light sensor settings can be configured using the free BEGA Tool app on a smartphone or tablet.
Q: What is the purpose of the time delay in the light sensor’s operation?
- A: The time delay prevents immediate responses to short-term brightness fluctuations in the environment. It typically ranges from 1 to 3 minutes.

Bollard tube with PIR and light sensor

Dimension

BEGA-84760-Bollard-Tube-with-PIR-and-Light-Sensor-
fig-1

Instructions for use

Application

Bollard tube ø 190 mm with integral passive infrared motion sensor and light sensor. For usage in the modular system bollard range. The integrated passive infrared motion and light sensor responds to heat emission in the dark and therefore activates in case of human or animal movement in the vicinity of the luminaire. Programming can be carried out using a smartphone or tablet via the free BEGA Tool app.

Safety

The installation and operation of this luminaire are subject to national safety regulations. Installation and commissioning may only be carried out by a qualified electrician. The manufacturer accepts no liability for damage caused by improper use or installation. If subsequent modifications are made to the luminaire, the person responsible for these modifications shall be considered the manufacturer.

EU Declaration of Conformity

BEGA Gantenbrink-Leuchten KG hereby declares that the radio system type 84 760 complies with Directive 2014/53/EU (RED). The complete text of the EU Declaration of Conformity is available at the following Internet address:

https://www.bega.com/conf/de/84760

Product Description

Bollard tube made of aluminium BEGA Unidure® coating technology Mounting plate made of cast aluminium for bolting onto a foundation or an anchorage unit

Mounting plate with two pitch circles:

ø 100 mm, 3 elongated holes 9 mm wide
ø 132 mm, 3 elongated holes 9 mm wide

Passive infrared motion sensor (PIR)

Range up to 12 m
Opening angle 120°-150°
Decals for reducing the detection range are provided
The minimum temperature difference between a moving object and the environment 4 °C
Object speed ideally 1 m/s
Adjustable sensitivity of the motion sensor (inertia)
Shut-down delay is adjustable between 5 s and 240 min
Light sensor: adjustable value range from darkness to approaching dusk (approx. 150 lx)
Fixed pre-set time hysteresis for suppression of undesired switching operations in luminaires during rapid brightness fluctuations Transmission frequency range: 2400-2483.5 MHz
Maximum transmission output: 10 mW
Connection box 71 084 for through-wiring – for 2 cables up to 7 × 6@
Fuse terminal with micro fuse 6,3 A slow ø 5 × 20 mm
Luminaire switchable via relay output (on/off) integrated in the sensor module
Relay contact with a switching capacity of 2300 W · 10 A
Please note the starting current of the switching loads (max. 100 A)
Ambient temperature: -25°C to +55°C 220-240 V 50-60 Hz
Safety class I
Protection class IP 65 dust-tight and protected against water jets only in combination with mounted bollard head or closing head Impact strength IK05 Protection against mechanical
impacts < 0.7 joule
Conformity mark
Weight: 6.4 kg

Installation

The luminaire foot must not be below the upper edge of the floor covering. Approximately 500 mm of cable above the mounting surface will suffice for connecting the luminaire to the power supply. Undo the screw at the base. Rotate and remove the mounting plate. In case of installation on a foundation, please observe the following: Wet concrete can be highly alkaline and must not come into contact with the luminaire permanently. We recommend draining the installation area and painting it with insulating paint. Using the provided mounting materials or other suitable mounting materials, screw-fit the mounting plate to a foundation or anchorage unit 70 896. Open the connection box. Lead the mains supply cable into the connection box. Make a connection of the phase with the L1 marked, the neutral wire at the N marked and earth conductor at the PE marked connecting terminal.

BEGA-84760-Bollard-Tube-with-PIR-and-Light-Sensor-
fig-2

Insert the bollard head into bollard tube and turn it clockwise as far as it will go, adjust if necessary and fix with lateral hexagon socket head screw. Pass the luminaire power supply cable through the top cable entry into the connection box. Make the earth conductor connection and the electrical connection. Make sure that the connection cable is correctly assigned. Connection of the brown wire from the bollard head to the loose terminal (L’). Close the connection box. Place luminaire onto the mounting plate, align and fix with screw.

Circuit variants

The luminaire can only be configured and controlled individually. Forwarding of the switching signal to additional luminaires can be achieved via the relay contact L’ (see circuit diagram 1).

Circuit diagram 1:

The first sensor of a luminaire controls a group of luminaires, while the second luminaire sensor controls another group. BEGA-84760-Bollard-Tube-with-
PIR-and-Light-Sensor-fig-3

Circuit diagram 2:

Sensors of multiple luminaires control the same luminaire group. All luminaires in the group will be switched on as soon as one of the sensors detects movement. It is important to note that all sensors within one group are fed via the same phase. BEGA-84760-Bollard-Tube-with-PIR-and-Light-
Sensor-fig-5

Commissioning

The power supply must be connected for the commissioning of the luminaire. The brightness sensor will need up to 10 minutes after activation of the power supply to correctly calibrate the brightness value. Once installed, the luminaire can be operated immediately in its factory settings; configuration via smartphone will not be required. The factory settings as are follows: Mode: PIR and light PIR sensitivity: 100 % (high sensitivity) Shut-down delay: 5 minutes Brightness threshold: 32 (approx. 50 lx) Alternatively, the integrated PIR motion and light sensor can be configured via smartphone or tablet using the free BEGA Tool app. The default values can be reinstated at any time via the BEGA Tool app.

Download app

Download the app for Android or iOS and add the luminaire as your starting point. The individual QR code required for set-up can be found in the enclosed set with decals for reducing the detection area. Store the QR code with your documentation (e.g. at the top of Page 1 in the instructions for use). Select the “Share Access” function in the BEGA Tool app if you want to use a different or additional smartphone for the configuration of the integrated sensor module or controlling the luminaire head. Alternatively, the luminaire will have to be reset to factory settings. Follow the in-app instructions.

Please note:

The integrated light sensor operates with a time delay to prevent responses to short-term brightness fluctuations in the environment of the luminaire. Time delay approx. 1 to 3 minutes. A manual darkening of the sensor will therefore not result in an immediate response.

Once commissioned successfully, you can choose between three operating modes and one manual control mode.

Operating modes

PIR motion and light sensor
PIR motion sensor only
Light sensor only

Manual switching:

Sensor deactivation and manual control of the luminaire (on/off)

Range / Detection area

The specifications for the range and detection area of the PIR motion sensor are reference values. The detection range is 120° to 150° at a depth of 5 m up to max. 12 m, depending on motion direction (see illustration). Too minor a temperature difference between the moving object and the ambient temperature can influence the detection range. Local conditions and external heat sources may affect both the range and the detection area BEGA-84760-Bollard-Tube-
with-PIR-and-Light-Sensor-fig-8

Reducing the detection range

Use the decals provided to reduce the vertical detection area of the sensor. The smaller decals reduce the detection area by around one-third, the larger ones by around one half (see sketch). Clean the sensor with a soft cloth soaked in alcohol before applying the decals. Ensure exact positioning when attaching the decals BEGA-84760-Bollard-Tube-with-PIR-and-Light-Sensor-
fig-9

Reset to factory settings

The luminaire must be switched off five times within 30 seconds for at least 2 seconds each time to manually reset it to factory settings (see sketch). The luminaire can furthermore be reset to the factory settings via the BEGA Tool app. The reset is confirmed with five flashes of the luminaire. The smartphone will be disconnected. BEGA-84760-Bollard-Tube-with-PIR-and-Light-Sensor-
fig-10

Status display

Status LED lights up green: The status LED lights up green if the motion sensor registers movement in test mode. When the power supply returns, the status LED flashes green 3 times. Status LED lights up blue: The status LED lights up blue if a direct Bluetooth connection to the sensor module was established. The LED will no longer light up if the Bluetooth connection is interrupted or test mode is activated.

Test mode

Test mode allows the user to test the motion sensor and simplifies sensor configuration in daylight. The test mode can be activated via the App BEGA Tool. In test mode, the status LED will light up green, once movement is detected in the detection range. The LED will no longer light up when no further movement is detected. Test mode is ended automatically when the relevant in-app configuration screen is exited or the Bluetooth connection is interrupted.

Please note:

Motion detection in test mode depends on the set motion sensitivity.

Cleaning Maintenance

Clean the luminaire regularly with solvent-free cleansers from dirt and deposits. Do not use high-pressure cleaners

Accessories

70 896 Anchorage unit with a mounting flange made of hot-dip galvanised steel. Overall length 500 mm.3 stainless steel M8 mounting screws. Pitch circle ø 132 mm.

Spares