Solar Lighting DIRECT SLDPL0007A-PIR Solar Powered Post Light with Motion Sensor Instructions

June 1, 2024
Solar Lighting DIRECT

INSTRUCTION GUIDE
Residential Single Head Post Light

Model No. SLDPL0007A-PIR, SLDPL0008A-PIR, SLDPL0009A-PIR, SLDPL0012A-PIR, SLDPL0018A-PIR

SLDPL0007A-PIR Solar Powered Post Light with Motion Sensor

IMPORTANT NOTES

  • Please ensure you place your solar panel in a location here it can achieve a minimum of 6HRS DIRECT SUNLIGHT
  • Be aware that on overcast/cloudy days, the solar panel will still charge. However, not as efficiently as a sunny day, so the battery may not reach full capacity. Therefore, your light may turn off earlier than specified
  • It’s best not to install the fitting underneath a street light, porch light etc. because this may stop the automatic daynight sensor triggering and result in your lights not turning on

TROUBLE SHOOTING

Phenomenon Cause Inspection Method Solution
Light won’t turn on Switch hasn’t been
turned on Determine what position the switch is in Turn the switch on
Battery has run flat Period of rainy or cloudy weather or installation site
doesn’t provide enough direct sunlight Charge the light in direct sunlight

for 1-2 days then check again
The light only stays on for a short amount of time| Low Battery| 1.Bad installation site for the solar panel
2.Dust or leaves are covering the panel
3.Long period of overcast weather| 1. Charge the battery in direct sunlight for 1-2
days with the switch off, then check again
2. Clean the solar panel
Battery Failure| 1. Access the light and & replace battery
2. Battery has matured| Contact SLD Customer Service to buy new batteries

LIGHT MODES

ON – PIR Sensor Override Mode
This setting overrides the built in sensor and your light will automatically turn on at dusk at 70% total brightness until the battery either runs flat or daylight is sensed
P – PIR Sensor Mode
This setting puts your light into sensor mode where by any movement detected will trigger the light toperform at 100% for approx. 1 minute. At all other times an ambient soft glow is emitted
OFF – Light is manually switched off and will not operate but will still charge – Do not leave in this setting for any extended period of time, 72hrs maximum

INSTALLATION METHOD

  1. Remove contents from packaging
    NOTE: Before continuing, we recommend you place your light direct sunlight (with the switch in the “OFF” position) for 2 days before installation

  2. Make sure to switch your light head to the mode you wish to operate in before installation (FIGURE 3)

  3. Using the supplied Nuts & Bolts, fix the post base mount in your desired location

  4. To connect the 4 part post – start with the bigger pieces on the bottom. Twist them into each other clockwise to tighten. Work towards the smaller pieces at the top (FIGURE 1)

  5. To connect light head to the post top, twist the light head into the adapter (FIGURE 2)

Solar Lighting DIRECT SLDPL0007A-PIR Solar Powered Post Light with Motion
Sensor - light head

Customer Service Number: 1300 135 91
www.solarlightingdirect.com.au

Documents / Resources

| Solar Lighting DIRECT SLDPL0007A-PIR Solar Powered Post Light with Motion Sensor [pdf] Instructions
SLDPL0007A-PIR, SLDPL0008A-PIR, SLDPL0009A-PIR, SLDPL0012A-PIR, SLDPL0018A- PIR, SLDPL0007A-PIR Solar Powered Post Light with Motion Sensor, Solar Powered Post Light with Motion Sensor, Powered Post Light with Motion Sensor, Light with Motion Sensor, Motion Sensor, Sensor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Solar Lighting DIRECT User Manuals

Related Manuals