SHARPER IMAGE 1012669 SPASTUDIO Shower Speaker User Manual

: June 6, 2024
: Sharper Image

Table of Contents

GETTING STARTED
CONNECT
MOUNT
USING YOUR SPEAKER
COMPATIBLE WITH
RECHARGEABLE BATTERY WARNING:
CONTENTS
FEATURES
SAFETY WARNINGS:
ART DEPARTMENT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SHARPER IMAGE®
SPASTUDIOT” SHOWER SPEAKER

GETTING STARTED

CHARGE

Make sure the speaker and cable are completely dry.
Remove the USB protector cover from the speaker.
Attach the small end of the USB charging cable to the speaker.
Attach the other end of the cable to a computer’s USB port.
Orange LED will turn on while the speaker is charging and turn off after it is fully charged.
Cover with water-resistant USB protector cover.

CONNECT

Place your Bluetooth-enabled device within 3 feet of the speaker.
Enable Bluetooth on your device and search for new Bluetooth devices.
Press and hold the power button to turn the speaker on.
Select SI Shower Speaker from the list of Bluetooth available devices.

MOUNT

Clean and dry a flat hard surface where the mounting plate will be placed.
Peel the red sticker from the plate.
Firmly press the plate onto the area for at least 1 minute.
Connect the magnetic back of the speaker to the plate.

USING YOUR SPEAKER

Once connected, use your device to stream music to the speaker.
Connect to a new device by pressing VOL+ and VOL-.
Speaker will power off after 10 minutes of not connecting.
Charge when LED Indicator begins to flash.
Hard reset by pressing the power button for 12 seconds.

COMPATIBLE WITH

RECHARGEABLE BATTERY WARNING:

This product contains batteries that are non-replaceable.
There is a risk of fire and personal injury if the battery is punctured, damaged, or misused.
Do not dismantle, crush, incinerate or short-circuit the battery.
Never expose the battery to extreme temperatures or moisture.
Keep away from flammable materials and direct sunlight.
Only charge using the provided charger, cable, and/or adopters. A rechargeable battery is only to be charged by an adult.
Adult supervision is required while charging the battery.
Allow the battery to cool to room temperature before charging. Charge on a non-flammable surface and keep away from flammable products.
Discontinue charging if the battery becomes hot, swells, smokes, or gives off a strong odor.
Battery chargers used with the product are to be regularly
examined for damage to the cord, plug, enclosure, and other parts. In the event of such damage, chargers must not be used until the damage has been repaired.
Recycle or dispose of battery according to federal, state, and local laws.
Keep these instructions for future reference.

THE Bluetooth WORD MARK AND LOGOS ARE REGISTERED TRADEMARKS OWNED BY BLUETOOTH SIG, INC.
SHARPER IMAGES NAMES AND LOGOS (INCLUDING THE 77 LOGO AND TOMORROW’S TOMORROW) ARE TRADEMARKS OR REGISTERED TRADEMARKS. DISTRIBUTED BY AND 0 2021 MERCHSOURCE, LLC. IRVINE CA 92618. ALL RIGHTS RESERVED. PRINTED IN CHINA.
KEEP THIS INSTRUCTION MANUAL AS IT CONTAINS IMPORTANT INFORMATION FOR FUTURE REFERENCE.
DUE TO CONTINUOUS PRODUCT IMPROVEMENTS, THE PICTURES ON THIS MANUAL MAY DIFFER SLIGHTLY FROM THE ACTUAL PRODUCT.

FEATURES

IPX7 waterproofing
Rechargeable battery
Built-in magnet for mounting speaker

SAFETY WARNINGS:

PLEASE READ BEFORE USE

Not a children’s item. Keep out of reach of children.
Inspect the product before every use. If the product appears worn, frayed, cracked, or broken in any manner, discontinue use and discard immediately.
Do not submerge in water.
Do not disassemble.
Do not use it for anything other than its intended purpose.
Do not charge the speaker in the shower or when it is wet.
Do not allow moisture to enter the USB port.

ART DEPARTMENT

Job # / Filename 2021-07-26_ShowerSpeakerVVithMagneticMount SLIM

| Product Line
Sharper Image
---|---
Designer
Shane/Nick| Brand Manager
Daniel D.| Finished Size
68mm W x 70mm H
File Format
Adobe Illustrator CC (live)/CS4 (OL)| Fonts Helvetica Neue, Manila Sans, DIN Next LT Pro

| Color (Spot or 4C)
4 Color Process| # of Colors
4
Printing Process / Finishing
Matte PP Coating| Comments
OUTSIDE
All copyright, trademark, and patent rights or any other intellectual property rights or material associated with the content provided herein, and the selection, coordination, and arrangement of such content, are owned exclusively by MERCHSOURCE LLC., or any third-party licensors. The use or misuse of any copyrights, trademarks, patents, or any other intellectual property or materials, except as permitted herein, is expressly prohibited. Any infringements shall be prosecuted to the fullest extent of the law, both foreign and domestic.