Luminii LETO-9 Recessed Fixed LED Downlight Instruction Manual

June 1, 2024
luminii

Luminii LETO-9 Recessed Fixed LED Downlight

Luminii-LETO-9-Recessed-Fixed-LED-Downlight-PRODUCT

Specifications

  • Product Name: LETO 9
  • Mounting Surface: Must hold at least 0.88lb (0.4kg)
  • Ceiling Thickness: Between 1/4″ & 1″ (6mm & 25mm)

Product Usage Instructions

Choose Installation Type

  1. Install appropriate housing between ceiling joists. Connect the driver to the line voltage and ground to the enclosure.

Retrofit & Non Fixed Driver Installation:

  1. Finish ceiling installation. Make sure the hole is cut to the appropriate size and location.
  2. Ensure the wire reaches the fixture location.
  3. Connect the driver to the line voltage and ground to the enclosure. Push the driver into the ceiling.

Installation Steps

CLICK!

  1. Insert the two ends of the springs into the pre-drilled holes on each side of the LETO 9.
  2. Once inserted, pull the coiled sections away from each other and place them over the two tabs.
  3. Ensure the power is off. Lower quick connect wire from the ceiling and connect to the fixture until you hear a click.
  4. Raise the 2 springs upward until they clear the hole in the ceiling.

Frequently Asked Questions (FAQ)

What should I do if my ceiling is thinner than 1/4″ (6mm)?

If the thickness of the ceiling is thinner than 1/4″ (6mm), use an #6-32 screw to set the fixture in place.

What should I do if I encounter unauthorized modifications or improper use of the product?

Unauthorized modifications and/or improper use void the warranty. Contact us at 403-216-7043 or info@sensolighting.com for assistance.

Overview

Luminii-LETO-9-Recessed-Fixed-LED-Downlight-FIG-1

Read and follow these instructions before installing or maintaining this product

  • This product is suitable for DRY INDOOR LOCATIONS ONLY
  • Make sure this product is NOT on the same circuit as inductive loads, (e.g. fluorescent bulbs, discharge bulbs, ventilation fans, etc…)
  • Allow air to flow freely around the fixture
  • Do not switch on line voltage until all wiring is complete
  • Incorrect wiring will result in irreparable damage to LED and power supply
  • This product should only be installed by a licensed electrician

Choose Installation Type

Housing InstallationLuminii-LETO-9-Recessed-Fixed-LED-Downlight-
FIG-2

  1. Install appropriate housing between ceiling joists. Connect the driver to the line voltage and ground to the enclosure.
  2. Finish ceiling installation. Make sure the hole is cut to the appropriate size and location.

Retrofit & Non-Fixed Driver InstallationLuminii-LETO-9-Recessed-Fixed-
LED-Downlight-FIG-3

  1. Ensure the wire reaches the fixture location.
  2. Finish ceiling installation. Make sure the hole is cut to the appropriate size and location.
  3. Connect the driver to the line voltage and ground to the enclosure. Push the driver into the ceiling.Luminii-LETO-9-Recessed-Fixed-LED-Downlight-FIG-4
  4. Insert the two ends of the springs into the two pre-drilled holes on each side of the Leto 9.
  5. Once inserted, pull the coiled sections away from each other and place them over the two tabs.
  6. Ensure the power is off. Lower quick connect wire from the ceiling and connect to the fixture until you hear a click.Luminii-LETO-9-Recessed-Fixed-LED-Downlight-FIG-5
  7. Raise the 2 springs upward until they clear the hole in the ceiling.

Dimension

Do not scale this when printing this template.

Warranty

  • This product must be installed under all applicable installation codes and ordinance
  • Limited five (5) years warranty
  • Warranty is void in the eventuality of unauthorized modifications and/or improper use

403-216-7043 info@sensolighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals