BEGA ISM-PRO-06 Office Desk Pronto Installation Guide

Table of Contents

BEGA-ISM-PRO-06-Office-Desk-Pronto-product

Product Usage Instructions

Ensure the product is placed on a stable surface.
Connect the product to the correct power supply within the specified input voltage range.
Make sure all accessories connected to the control box meet the required specifications.
Press the designated buttons on the control panel to operate the desk frame.
Use the Up and Down keys on the display screen to adjust the desk height.
To save specific heights, use the Memory keys.
Follow the safety instructions provided in the manual for optimal usage.

Q: What should I do if the product encounters an error code?
A: Refer to the error code list in the manual to identify the issue. If needed, contact the manufacturer or service agent for assistance.
Q: How do I adjust the sensitivity settings on the product?
A: Navigate to the settings menu using the designated buttons on the control panel. Follow the instructions provided in the manual to adjust sensitivity settings as required.

BEGA-ISM-PRO-06-Office-Desk-Pronto-fig-1 BEGA-
ISM-PRO-06-Office-Desk-Pronto-fig-2

Safety warning

Please read this manual carefully before use.
The product must be connected to the correct power supply.
For any accessories connected to the control box, the plug type and electrical characteristics must conform to its specifications.
Indoor use only.
If the transformer’s external cable is damaged and needs to be replaced,new accessory will be provided by the manufacturer or its service agent.

TOOLS INCLUDED

TOOLS REQUIRED

BEGA-ISM-PRO-06-Office-Desk-Pronto-fig-12 BEGA-
ISM-PRO-06-Office-Desk-Pronto-fig-13

BEGA-ISM-PRO-06-Office-Desk-Pronto-fig-17

The whole handset surface is a button panel.
If there is no press within 30 seconds, the screen is locked and 1/2/3/4/S keys are locked correspondingly, you should press the Up or Down key first, it can be used when the display screen lights up.

Display Screen

Up & Down Keys

Please keep pressing the UP/DOWN key to adjust the desk height until you get an optimum height.

Memory Key （1/2/3/4）

How to set memory mode

Click the “S” key when running to a specific point. The display screen displays “S-” and “-” flashes.
At this time, press the “1-4” button to store the position to the corresponding label. the memory height is successfully saved, Then light press 1/2/3/4, and the desk moves to memory height automatically.

Set Key(S)

Initialization

When”RST” is on the display screen, press the” “button until the desk frame reaches its lowest point. After hearing the “di” sound and desk frame rebounds, initialization is completed. (P.S. The button cannot be released during this operation, otherwise, the initialization will fail)
Forced initialization: Press the” “button until the desk frame reaches its lowest point, then release the button and press it again for about 5 seconds until hear the “di” sound the desk frame rebounds, and the initialization is completed.
Restore the factory settings: When the new controller is changed or the parameters need to be restored to the factory settings, press the” “and” “buttons simultaneously, you will hear the first “di” sound after about 5 seconds and the second “di” sound after 10 seconds. When the display screen shows “RST”, please operate and refer to the No.1 item.

When the desktop is on the rise or down, and encounters reverse resistance, the desk will rebound.

Error code	Fault cause	Solution
E1,E6,E7	power fault	change power
E2	nsynchronous height over 1cm	Implement the initialization operation 1
E4	handset fault	Unplug and replug the cable of the handset
E5	Anticollision alert	Rebound reminder, normal condition
E8	desktop sloping	check the desktop
E11,E21	Motor defect	inspect the motor wire
E12,E22	controller fault	Exchange the controller
E14~E17,E24~E27	motor fault	change motor
E18,E28	overloading	reduce the loading
HOT	overtime operation	Automatic recovery after stopping use for 20 minutes

Reset original status: Press” “and” “in 10 seconds till hear a bee sound, now the system into factory default data.
Limited height setting:Press” “and” “key for 5 seconds till hear a bee sound, limited height setting success. (minimum limited height＜96， maximum limited height＞97).
Lock and unlock:Press” “and ” S ” key for 5 seconds, Screen displays “LOC”, system locked up, Press” “and ” S ” key for 5 seconds, screen displays “LOC” turns to a number, and system unlocked.

BEGA-ISM-PRO-06-Office-Desk-Pronto-fig-21