VISUAL COMFORT CHC 5872 Medium Wrapped Ring Chandelier Instruction Manual

VISUAL COMFORT CHC 5872 Medium Wrapped Ring Chandelier

Product Information

Item # CHC 5872

This Darlana Medium Wrapped Ring Chandelier is a stylish and elegant lighting fixture that adds a touch of sophistication to any space. It is designed to be installed in accordance with all applicable local installation codes and should be handled by a person familiar with its construction and operation. Please inspect the item and its contents carefully before installation. If any damage or defect is found, do not proceed with the installation. Retain all packaging material until the installation is complete and approved.

Tools Required (Not Included):

• Phillips Screwdriver
• Slip Joint Pliers
• Wire Strippers
• Slotted Screwdriver
• Measuring Tape
• Chain Pliers
• Wire Cutters

Product Usage Instructions

1. Carefully remove all parts from the box and place them on a clean, soft surface.
2. Install the mounting plate (B) to the junction box using the provided mounting screws (C).
3. Secure the collar loop (D) to the mounting plate (B) by tightening the locknut with pliers.
4. Attach the canopy (E) to the collar loop (D) and secure it with the collar ring (F).
5. Determine the desired overall length and the amount of chain (H) needed. Use chain pliers to shorten the chain as required, keeping any extra chain for future use.
6. Attach the chain (H) to the collar loop (D) and the fixture loop (I) using quick links (G). Make sure to secure the quick links.
7. Attach the chains (J) to the fixture loop (I) and the fixture frame (M) using hooks (K).
8. Thread the fixture wire and ground wire through the chains (J & H). When reaching the collar loop (D), ensure there is no tension on the wires. Cut any excess wires, leaving enough length to reach the junction box.
9. Separate the two sides of the molded wire and strip insulation on each side by 5/8 inch.
10. Loosen the collar ring (F) and carefully let the canopy (E) slip down the chain (H).
11. Twist all fixture wires together and slip them through the center hole of the collar loop (D). Untwist the wires and separate them in preparation for connection.
12. Wrap the fixture ground wire (bare copper) around the green grounding screw as shown in Diagram 1 and tighten it. Connect the fixture ground wire to the supply ground wire using a wire nut (A). Note that proper grounding of the fixture is essential.
13. Connect the fixture neutral wire (ribbed) to the supply neutral wire (usually white) using a wire nut (A).
14. Connect the fixture hot wire (smooth with markings) to the supply hot wire (usually black) using a wire nut (A). Be cautious not to reverse the hot and neutral connections.
15. Ensure all wire connections are tight and carefully tuck them into the junction box.
16. Install the canopy (E) to the collar loop (D) and secure it with the collar ring (F).
17. Finally, install the light bulbs into the sockets.

Care Instructions: Clean the chandelier only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.

Item # CHC 5872

NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED)

• Phillips Screwdriver
• Slip Joint Pliers
• Wire Strippers
• Slotted Screwdriver
• Measuring Tape
• Chain Pliers
• Wire Cutters

ASSEMBLY INSTRUCTIONS

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Install mounting plate (B) to the junction box and secure with mounting screws (C).

3. Secure collar loop (D) to mounting plate (B) using pliers to tighten locknut.

4. Install canopy (E) to collar loop (D) and secure with collar ring (F).

5. Determine desired overall length, and amount of chain (H) needed. Shorten chain using chain pliers. (Keep extra chain)

6. Attach chain (H) to collar loop (D) and fixture loop (I) using quick links (G). Secure quick links (G).

7. Attach chains (J) to fixture loop (I) and fixture frame (M) using hooks (K).

8. Thread fixture wire and ground wire through chains (J & H).
   NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box.

9. Separate two sides of molded wire, and strip insulation on each 5/8″.

10. Loosen collar ring (F) and let canopy (E) slip down chain (H) carefully.

11. Twist all fixture wires together, and slip through center hole of collar loop (D).
    NOTE: Untwist wires and separate to prepare for connection.

12. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A).
    NOTE: It is imperative that the fixture is grounded.

13. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).

14. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A).
    CAUTION: Do not reverse the hot and neutral connections.

15. Make sure all wire connections are tight, then carefully tuck into the junction box.

16. Install canopy (E) to collar loop (D) and secure with collar ring (F).

17. Install light bulbs into the sockets.

Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>